Hollyland - Wireless Lavalier Microphone | Video Transmitter | Intercom System
User Guide for HOLLYLAND models including: Solidcom SE Pro 4 Person Full Duplex Single Ear Noise Canceling Headset, Solidcom SE Pro, 4 Person Full Duplex Single Ear Noise Canceling Headset, Duplex Single Ear Noise Canceling Headset, Single Ear Noise Canceling Headset, Noise Canceling Headset, Canceling Headset
Download
File Info : application/pdf, 12 Pages, 3.16MB
DocumentDocumentSolidcom SE Pro Quick Guide V1.0 Foreword Thank you for choosing the Solidcom SE Pro for on-site communication. If you have never used a wireless intercom system before, then you are about to experience one of the most exciting products in the industry. This Quick Guide will show you how to get started with the product. Please read this Quick Guide carefully. We wish you a pleasant experience. To obtain Quick Guide information in other languages, please scan the QR code below. EN-2 Configuration Master Headset (Green) Remote Headset (Black) 6-Slot Charging Base 8-Slot Charging Base Number Stickers 01 USB-A to USB-C Cable Li-ion Battery Pack 770 Quick Guide & Packing List Card Warranty Card & Compliance Information Carrying Case Note: The quantity of the items depends on the product configuration detailed on the packing list card. EN-3 Overview Volume + Button (Long press for 5s to enter pairing mode) Microphone Hole (only for environ- mental sound) Volume - Button Speaker Battery Compartment Battery Compartment Button TALK/MUTE Button (Single press to switch status; long press to enable PTT function) USB-C Port (for firmware upgrade and audio output) Power Switch Battery/Connection Indicator Indicator Orange: charging Green: fully charged EN-4 Charging Contacts USB-C Port (for power supply) Overview Indicator Introduction Indicator Disconnected*: slowly flashing green light Pairing: rapidly flashing green light TALK Status: solid green light MUTE Status: solid red light Low Battery: slowly flashing red light USB-C Charging: A. Charging While Powered On: slowly flashing yellow light for 3s before returning to the former light B. Charging While Powered Off: slowly flashing yellow light USB-C Fully Charged: solid yellow light Upgrading: alternately flashing red and green light Notification Sound Introduction Low Battery: low battery level Ding: maximum volume Tick: mic boom in position of mic on or off Connected: device connected Disconnected: device disconnected Unmuted: mic on Muted: mic off * While disconnected, the remote headset shows slowly flashing green light while the master headset shows solid green light. EN-5 Operations Installing and removing the battery Place the battery into the battery compartment for installation. Press the battery compartment button to pop out the battery for removal. Turning on the device and confirming connection Headband Connection Indicator Power Switch 1. Toggle the power switch to turn on the headsets. 2. The indicator light changing from flashing green to solid green indicates successful connection. 3. The master headset has a brown headband while the remote headset has a black headband. EN-6 Operations Turning on the microphone MUTE MUTE TALK 85° TALK 85° TALK 85° TALK 85° 110° TALK Clockwise 110° TALK Counterclockwise Beginning your work Headset Pairing All remote headsets are prepaired with the master headset at the factory, so they are ready to use upon poweron. Pairing is only necessary when adding new headsets to an existing system. Ensure that the master headset and all remote headsets are powered on while pairing. 1. Long press the volume + button on both the master and remote headsets for 5s and the indicator lights will flash rapidly. 2. The indicator lights turning solid indicates successful connection. EN-7 Specifications Product Name LOS Range Operating Frequency Modulation Mode Transmit Power Receiver Sensitivity Battery Capacity Charging Time Frequency Response SNR Distortion Microphone Type Maximum Input SPL Output SPL Environmental Noise Reduction Weight Temperature Solidcom SE Pro Single-Ear Headset 1,300ft (400m) 1.9 GHz (DECT) GFSK 21dBm (125.9mW) < -90 dBm 770 mAH (2.926Wh) < 3 hours 150 Hz - 7 kHz (±10dB) 71±2dB @94dB SPL, 1 kHz < 1% @94dB SPL, 150 Hz - 7 kHz Electret > 115dB SPL 98dB SPL (@94dB SPL, 1kHz) > 20dB (from all directions) 185.2g (with battery) 0 - 45 (working) -10 - 60 (storage) Note: Due to differences in various countries and regions, there may be variations in the operating frequency and wireless transmit power of the product. EN-8 Specifications Product Name Port Dimensions Weight Charging Power Power Supply Charging Current Charging Time Temperature 6-Slot Charging Base 8-Slot Charging Base USB-C Port; Charging Contacts 119.3 × 57.6 × 34.6mm (4.7 × 2.3 × 1.4in.) 154.5 × 57.6 × 34.6mm (6.1 × 2.3 × 1.4in.) 91.1g 121.6g 10W 4.75 - 5.25V 380mA/Slot < 3 hours (6 batteries) < 4 hours (8 batteries) 0 - 45 (working) -20 - 60 (storage) The power delivered by the charger must be between min 1.5 Watts required by the radio equipment, and max 3 Watts in order to achieve the maximum charging speed. EN-9 Disclaimer Safety Precautions Do not place the device near or inside heating devices (including but not limited to microwave ovens, induction cookers, electric ovens, electric heaters, pressure cookers, water heaters, and gas stoves) to prevent the battery from overheating and exploding. Use the original charger, data cables, and batteries provided with the product. Using unauthorized or incompatible chargers, data cables, or batteries may cause electric shock, fire, explosion, or other dangers. Support If you encounter any problems in using the product or need any help, please contact Hollyland Support Team via the following ways: Hollyland User Group HollylandTech HollylandTech HollylandTech support@hollyland.com www.hollyland.com Statement: All copyrights belong to Shenzhen Hollyland Technology Co., Ltd. Without the written approval of Shenzhen Hollyland Technology Co., Ltd., no organization or individual may copy or reproduce part or all of any written or illustrative content and disseminate it in any form. Trademark Statement: All the trademarks are owned by Shenzhen Hollyland Technology Co., Ltd. Note: Due to product version upgrades or other reasons, this Quick Guide will be updated from time to time. Unless otherwise agreed, this document is provided as a guide for use only. All representations, information, and recommendations in this document do not constitute warranties of any kind, express or implied. EN-10 Manufacturer: Shenzhen Hollyland Technology Co., Ltd. Address: 8F, 5D Building, Skyworth Innovation Valley, Tangtou Road, Shiyan Street, Baoan District, Shenzhen, 518108, China MADE IN CHINA P/N:3003080664