User Manual for SUNNY HEALTH FITNESS models including: SF-RB4936, SF-E320047, SF-E320047 Elite Interactive Series Exercise Elliptical, SF-E320047, Elite Interactive Series Exercise Elliptical, Series Exercise Elliptical, Exercise Elliptical, Elliptical
Sunny Health & Fitness Elite Interactive Series Exercise Elliptical with Exclusive SunnyFit App Enhanced Bluetooth Connectivity - SF-E320047 : Sports & Outdoors
SF-E320047 User Manual (PDF) Sunny Health & Fitness Sunny Health & Fitness Sunny,Health,&,Fitness,Legacy,Stepping,Elliptical,Machine,,Total,Body,Cross,Trainer,,Low,Impact,Exercise,Equipment,with,Optional,SunnyFit,App,Enhanced,Connectivity,B0CK54R6D8,B002R8CPRY,B09S85F3RK,B09R3WT416
File Info : application/pdf, 22 Pages, 1.57MB
DocumentDocumentELITE INTERACTIVE SERIES EXERCISE ELLIPTICAL
SF-E320047
USER MANUAL
IMPORTANT! Please retain owner's manual for maintenance and adjustment instructions. Your satisfaction is very important to us, PLEASE DO NOT RETURN UNTIL YOU HAVE CONTACTED US: support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
IMPORTANT SAFETY INFORMATION
We thank you for choosing our product. To ensure your safety and health, please use this equipment correctly. It is important to read this entire manual before assembling and using the equipment. Safe and effective use can only be achieved if the equipment is assembled, maintained, and used properly. It is your responsibility to ensure that all users of the equipment are informed of all warnings and precautions.
1. Before starting any exercise program, you should consult your physician to determine if you have any medical or physical conditions that could put your health and safety at risk or prevent you from using the equipment properly. Your physician's advice is essential if you are taking medication that affects your heart rate, blood pressure, or cholesterol level.
2. Be aware of your body's signals. Incorrect or excessive exercise can damage your health. Stop exercising if you experience any of the following symptoms: pain, tightness in your chest, irregular heartbeat, shortness of breath, lightheadedness, dizziness, or feelings of nausea. If you do experience any of these conditions, you should consult your physician before continuing with your exercise program.
3. Keep children and pets away from the equipment. The equipment is designed for adult use only. 4. Use the equipment on a solid, flat level surface with a protective cover for your floor or carpet.
To ensure safety, the equipment should have at least 2 feet (60 CM) of free space all around it. 5. Ensure that all nuts and bolts are securely tightened before using the equipment. The safety of
the equipment can only be maintained if it is regularly examined for damage and/or wear and tear. 6. Always use the equipment as indicated. If you find any defective components while assembling or checking the equipment, or if you hear any unusual noises coming from the equipment during exercise, discontinue use of the equipment immediately and do not use until the problem has been rectified. 7. Wear suitable clothing while using the equipment. Avoid wearing loose clothing that may become entangled in the equipment. 8. Do not place fingers or objects into the moving parts of the equipment. 9. The maximum weight capacity of this unit is 275 pounds (125 KG). 10. The equipment is not suitable for therapeutic use. 11. To avoid bodily injury and/or damage to the product or property, proper lifting and moving are required. 12. Your product is intended for use in cool, dry conditions. You should avoid storage in extreme cold, hot, or damp areas as this may lead to corrosion and other related problems. 13. This equipment is designed for indoor and home use only; it is not intended for commercial use.
1
PRE-ASSEMBLY CHECK LIST
Before you start to assemble, please make sure all parts are included
No.
Description
1 Main Frame
3 Rear Stabilizer
Left Swing Rod/ Left Foot Bar/ 5/7/54
U Bracket
9 Left Handlebar
11 Middle Handlebar
27/28 Left Swing Rod Cover-A/B
38/39 Left Foot Bar Cover-A/B 63/64 Left / Right Decorative Cover 48/49 Left / Right Pedal
20 Computer 74 Bottle Holder
Spec. Qty. 1 1
1SET
1 1 1SET 1SET 1SET 1SET 1 1
No.
Description
2
Front Stabilizer
4
Front Post
Right Swing Rod/ Right Foot 6/8/54
Bar/ U Bracket
10 Right Handlebar
19 Clamp Cover
29/30 Right Swing Rod Cover-A/B
40/41 Right Foot Bar Cover-A/B A Hardware Package B Thank You Card C Manual D AA Battery
Spec. Qty. 1 1
1SET
1 1 1SET 1SET 1 1 1 2
2
HARDWARE PACKAGE
Ordering Replacement Parts (U.S. and Canadian Customers only) Please provide the following information in order for us to accurately identify the part(s) needed: The model number (found on cover of manual) The product name (found on cover of manual) The part number found on the "EXPLODED DIAGRAM" and "PARTS LIST" (found near on the
page17-21) Please contact us at support@sunnyhealthfitness.com or 1- 877 - 90SUNNY (877-907-8669)
3
ASSEMBLY INSTRUCTIONS
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
STEP 1: Unscrew 4 Screws (No. 70) from Main Frame (No. 1) with Allen Wrench (No. 121). Remove 4 Plastic Washers (No. 119) and 2 Shipping Tubes (No. 120) from Main Frame (No. 1). You may save these parts Screws (No. 70), Plastic Washers (No. 119),Shipping Tubes (No. 120)in case you would like to repackage and transport this equipment in the future.
STEP 2: Attach the Front Stabilizer (No. 2) and Rear Stabilizer (No. 3) to the Main Frame (No. 1) with 4 Bolts (No. 67) and 4 Washers (No. 45). Tighten and secure with Allen Wrench (No. 121).
4
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
STEP 3:
Remove 6 Screws (No. 70), 4 Washers (No. 45), 2 Big Arc Washers (No. 25) and 6 Spring Washers (No. 17) from the Main Frame (No. 1) with Allen Wrench (No. 121).
CAUTION: Please make sure the Tension Control Knob (No. 75) is at the lowest resistance level (level 1, all the way to the left) before you connect any wires together.
Attach the Tension Control Wire (No. 75a) into the metal bracket of Tension Wire (No. 71) as shown in drawing A. Then, pull Tension Control Wire (No. 75a) upward and insert it into the slot of metal bracket of Tension Wire (No. 71) as shown in drawing B. Make sure the metal fitting on Tension Control Wire (No. 75a) is secured in the metal bracket.
Connect the Extension Sensor Wire (No. 73) with Sensor Wire (No. 72). Insert the connecting wires into Front Post (No. 4).
Attach the Front Post (No. 4) to the Main Frame (No. 1) with 6 Screws (No. 70), 4 Washers (No. 45), 2 Big Arc Washers (No. 25) and 6 Spring Washers (No. 17) that were removed. Tighten and secure with Allen Wrench (No. 121).
NOTE: Be careful not to pinch any wires when attaching Front Post (No. 4) to Main Frame (No. 1).
5
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
STEP 4: Attach the Left Decorative Cover (No. 63) and Right Decorative Cover (No. 64) to the Main Frame (No. 1) with 4 Screws (No. 42). Tighten and secure with Spanner (No. 123).
6
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
STEP 5:
Remove 2 Bolts (No. 31), 2 Spring Washers (No. 17), 2 Big Washers (No. 32) and 2 Wave Washers (No. 34) from the Front Post (No. 4) with Spanner (No. 123).
Attach the Left Swing Rod (No. 5) onto the left horizontal axis of the Front Post (No. 4) with 1 Bolt (No. 31), 1 Spring Washer (No. 17), 1 Big Washer (No. 32) and 1 Wave Washer (No. 34) that were removed. Tighten and secure with Spanner (No. 123).
Attach the U Bracket (No. 54) on the Left Foot Bar (No. 7) to the Left Crank (No. 89) with 1 Left Pedal Bolt (No. 57), 1 Wave Washer (No. 58). Turn the Left Pedal Bolt (No. 57) counter-clockwise as tightly as you can with your hand. Secure by tightening 1 Spring Washer (No. 59) and 1 Left Nylon Nut (No. 60) clockwise. Then use Allen Wrench (No. 122) and Spanner (No. 124) to tighten securely.
Attach the Right Swing Rod (No. 6) onto the right horizontal axis of the Front Post (No. 4) with 1 Bolt (No. 31), 1 Spring Washer (No. 17), 1 Big Washer (No. 32) and 1 Wave Washer (No. 34) that were removed. Tighten and secure with Spanner (No. 123).
Attach the U Bracket (No. 54) on the Right Foot Bar (No. 8) to the Right Crank (No. 90) with 1 Right Pedal Bolt (No. 61), 1 Wave Washer (No. 58). Turn the Right Pedal Bolt (No. 61) clockwise as tightly as you can with your hand. Secure by tightening 1 Spring Washer (No. 59) and 1 Right Nylon Nut (No. 62) counter-clockwise. Then use Allen Wrench (No. 122) and Spanner (No. 124) to tighten securely.
7
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
STEP 6:
Attach the Left Pedal (No. 48) to the Left Foot Bar (No. 7) with 2 Bolts (No. 47), 2 Washers (No. 45) and 2 Nuts (No. 26). Tighten and secure with Spanner (No. 123).
Attach the Right Pedal (No. 49) to the Right Foot Bar (No. 8) with 2 Bolts (No. 47), 2 Washers (No. 45) and 2 Nuts (No. 26). Tighten and secure with Spanner (No. 123).
Attach the Left Foot Bar Cover-A (No. 38) and Left Foot Bar Cover-B (No. 39) to the Left Foot Bar (No. 7) with 3 Screws (No. 42). Tighten and secure with Spanner (No. 123).
Attach the Right Foot Bar Cover-A (No. 40) and Right Foot Bar Cover-B (No. 41) to the Right Foot Bar (No. 8) with 3 Screws (No. 42). Tighten and secure with Spanner (No. 123).
STEP 7:
Attach the Left Handlebar (No. 9) to the Left Swing Rod (No. 5) with 2 Bolts (No. 24), 2 Big Arc Washers (No. 25) and 2 Nuts (No. 26). Tighten and secure with Spanner (No. 123).
Attach the Right Handlebar (No. 10) to the Right Swing Rod (No. 6) with 2 Bolts (No. 24), 2 Big Arc Washers (No. 25) and 2 Nuts (No. 26). Tighten and secure with Spanner (No. 123).
8
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
STEP 8: Attach the Left Swing Rod Cover-A (No. 27) and Left Swing Rod Cover-B (No. 28) to the Left Swing Rod (No. 5) by hand. Attach the Right Swing Rod Cover-A (No. 29) and Right Swing Rod Cover-B (No. 30) to the Right Swing Rod (No. 6) by hand.
STEP 9: Attach the Middle Handlebar (No. 11) to the Front Post (No. 4) with 2 Bolts (No. 18) and 2 Spring Washers (No. 17). Tighten and secure with Allen Wrench (No. 121). Attach Clamp Cover (No. 19) to the Middle Handlebar (No. 11) by hand.
9
We value your experience using Sunny Health and Fitness products. For assistance with parts or troubleshooting, please contact us at support@sunnyhealthfitness.com or 1-877-90SUNNY (877-907-8669).
STEP 10: Remove 4 Screws (No. 21) from the back of the Computer (No. 20) with the Spanner (No. 123). Connect the Extension Sensor Wire (No. 73) with Computer Wire (No. 20a). Then insert them into the Front Post (No. 4). Insert the Handle Pulse Wire (No. 14a) into the Pulse Input jack on the back of Computer (No. 20). Attach Computer (No. 20) to the top end of the Front Post (No. 4) with 4 Screws (No. 21) that were removed. Tighten and secure with Spanner (No. 123).
STEP 11: Attach Bottle Holder (No. 74) to the Front Post (No. 4) with 2 Screws (No. 21). Tighten and secure with Spanner (No. 123). The assembly is complete!
10
BATTERY INSTALLATION & REPLACEMENT
BATTERY INSTALLATION 1. Take out 2 AA batteries from computer box. 2. Press the buckle of battery cover on the Computer (No. 20), then remove battery cover. 3. Install 2 AA batteries into the battery case on the back of the Computer (No. 20). Pay attention
to the battery + and poles before installing. 4. Press the buckle of battery cover, then put the battery cover back to the back of the Computer
(No. 20). The installation is complete! BATTERY REPLACEMENT 1. Press the buckle of battery cover on the back of the Computer (No. 20), then remove battery
cover. 2. Remove the 2 old AA batteries in the battery case and install 2 new AA batteries into the battery
case on the back of the Computer (No. 20). Pay attention to the battery + and poles before installing. 3. Press the buckle of battery cover, then put the battery cover back to the back of the Computer (No. 20). The replacement is complete! BATTERY DISPOSAL Dispose the batteries according to the laws and regulations of your local region. Some batteries may be recycled. When disposing or recycling, do not mix battery types.
11
ADJUSTMENTS GUIDE
MOVING THE ELLIPTICAL BIKE
Press the Middle Handlebar (No. 11) and tilt the elliptical bike until the Transportation Wheels (No. 69) touch the ground. Now you can transport the elliptical bike to the desired location with ease.
ADJUSTING THE BALANCE
In order to achieve a smooth and comfortable ride, you must ensure that the elliptical bike is stabled and secured. If you notice that the elliptical bike is unbalanced during use, you should adjust the Adjustable End Caps (No. 65) located on the front and rear stabilizers until the elliptical bike becomes levelled with the floor surface. ADJUSTING THE TENSION
Adjust the tension by rotating the Tension Control Knob (No. 75) clockwise to increase the level of resistance. Rotate the Tension Control Knob (No. 75) counter-clockwise to decrease the level of resistance. Tension levels are set at Level 1 being the lowest and Level 12 being the highest. CLEANING The elliptical bike can be cleaned with a soft, clean, damp cloth. Do not use abrasives or solvents on plastic parts. Please wipe your perspiration off the elliptical bike after each use. Be careful not to get excessive moisture on the computer display panel as this might cause electrical hazard or electronics to fail. Please keep the elliptical bike, especially the computer, out of direct sunlight to prevent screen damage. Please inspect all assembly bolts and pedals on the elliptical bike for proper tightness every week. STORAGE Store the elliptical bike in a clean and dry environment, away from children.
12
EXERCISE COMPUTER
FUNCTION BUTTONS
MODE 1. Press the button to select hour, minute, year, month and date for setting. 2. Press the button to select TIME, DISTANCE, CALORIES and PULSE to preset. 3. Press the button for selection function display on main LCD, or enter after setting. 4. Press the button to confirm setting value of gender, age, height and weight. 5. Press the button and hold for 2 seconds to reset all value to zero. (When the user replace batteries, all the values will reset to ZERO automatically.) SET 1. To set up the hour, minute, year, month and date. 2. To set up the target value of Time, Distance, Calories and Pulse. You can hold the button to
increase the value fast. (The computer has to be in stop condition.) 3. To set up the personal data of gender, age, height and weight for Body fat test. RESET Press the button to reset function value when setting. (When the user replace batteries, all the values will reset to ZERO automatically.) BODY FAT Press this button to enter Body Fat measure function, then press MODE key to enter the setting Mode of your personal data of Gender, Age, Height and Weight. After finished setting, press it again to measure your Body fat ration (FAT%) and BMI. RECOVERY To act the heart rate recovery function after pulse signal in. Press any button to return to the main display. FUNCTIONS SCAN Automatically scan through each mode in sequence every 6 seconds. The display loop is RPM Speed Time Distance Calorie - Pulse on the main screen. TIME
Accumulates total time from 00:00 up to 99:59. The user may preset target time by pressing SET &MODE button. Each increase is 1 minute. RPM Displays the Rotation per Minute (RPM). The RPM and SPEED will switch to another display in every 6 seconds after exercise starts. SPEED Displays current training speed. Maximum speed is 99.9 km/h or mile/h. DISTANCE Accumulates total distance from 0.00 up to 99.99 km or mile. The user may preset target Distance data by pressing SET & MODE button. Each increase setting is 0.5 km or mile.
13
CALORIES Accumulates calories consumption during training from 0 to max. 999 calories. The user may also preset the target calorie before training by press SET & MODE button. Each setting increase is10 cal. Note : This data is a rough guide for comparison of different exercise sessions which can not be used in medical treatment.
PULSE The monitor will display the user's heart rate in beats per minute during training. You may set the target heart rate by press the SET & MODE button. CALENDAR
The monitor will display date, month, and year when the monitor is in sleep mode. CLOCK
The monitor will display current clock time when the monitor is in sleep mode. TEMPERATURE Displays current room temperature from 10 to 60when the monitor is in sleep mode.
OPERATION ORDER:
1. Power on Installs 2 pieces of 1.5V UM-3 or AA batteries. The monitor start to segment test with a long beep sound. (Whenever batteries are removed, all the functions values will be reset to zero or default value.)
2. Set current data Press the SET and MODE buttons to set up current clock time, year, month, and date. After the first setting till batteries be replaced next time, those preset data will be updated automatically.
3. Select and preset target value Get access to the setting function of Time, Distance, Calories and Target Pulse. When you are in each setting mode. For instance the Time setting, when the time value is glitter, you can press the SET button to adjust the value. Press the MODE button for confirmation and skip to next setting. The setting of Distance & Calories is the same as Time setting.
4. After entering speed signal, each function of SPEED-RPMTIME-DISTANCE-CALORIESPULSE will skip to display in every 6 seconds.
5. You can also press the MODE button to select single function display on the main screen except RPM & SPEED. The RPM & SPEED function will switch display in 6 seconds.
6. If you have preset any function target before, the function starts to count down from the target when the training starts. Once the target is achieved, the monitor will beep and the function will count up from zero automatically if the training is still going.
7. Pulse measurement After you hold on two handgrip sensors in a few seconds, the monitor will show up your current heart rate in beats per minute. To ensure the heart rate readout precisely, please do not hold one hand only. You may preset target pulse before training starts. Once your current heart rate is achieved to the target, the value of pulse will beep to remind you.
14
8. Recovery When the PULSE is working, you can press "RECOVERY" button to start the recovery test function. The monitor will count down from 0:60 second to 0:00 and the heart beat symbol will be glitter till counting down to "0:00". During 60 seconds counting period, please keep heart rate sensor is attached. Then the screen will display "F1 to F6" to show your recovery status. F1 is the best, and the F6 is the worst. You may keep exercising to improve your heart rate recovery status, and check it by using Recovery function.
9. Body Fat a) Press BODY FAT key to enter body fat measurement. b) Press MODE and SET buttons to input your personal data. Each personal data available setting area is described as the following: c) AGE: 10 ~ 99 years HEIGHT: 100 ~ 250 cm (or 3'03" ~ 8'02") WEIGHT: 10 ~ 200 kg (or 22 ~ 440 lb) d) After all personal data have been input, you can press BODY FAT button and hold on grip conductors to start the body fat testing. e) It takes few seconds to test the body fat. If you did not hold on the conductor during the testing procedure, the LCD will show the error sign Err after 10 seconds period. f) After the testing is finished, you will see fat advice in percentage and BMI figure (body mass Index) display on the main LCD in sequence by scan mode. g) BODY FAT % : Calculate from your personal data to show the value from 5%~50%. h) BMI : Calculate from your personal data to show the value from 1.0~99.99. i) Press any key to return to the main display.
Note 1. Stop training for 4 minutes, the screen will show up room temperature, clock, and calendar
display automatically. 2. If the computer displays abnormally, please re-install the battery and try again. 3. Battery Spec: 1.5V UM-3 or AA (2PCS).
APP CONNECTION:
1. Scan the QR code below to download the SunnyFit app onto your mobile device.
2. If this is your first time using the SunnyFit app, follow the in-app instructions to register for your free SunnyFit account and log in.
3. Ensure that the Bluetooth function is turned on from your mobile device.
15
4. To connect the equipment to the SunnyFit app: a. From the "Workout" tab, press on the "Search" button to search for your equipment. b. Once your equipment appears on the list, tap the "Select" button to confirm. c. Note: If your equipment does not appear on the "Searching for Equipment" list, check the EXERCISE COMPUTER on your equipment to ensure that it is not in sleep mode and your phone's Bluetooth function is on, then tap "Retry" to search again. d. Once your equipment shows up on the "Workout" tab as "Currently Selected", your equipment is now ready to display, track, and record your equipment's workout stats on the app!
5. If you are unable to replicate these steps, or have any other issues with the SunnyFit app, please contact SunnyFit support at support@sunnyfit.com, or use the in-app "Contact Us" form to request support ("Me" tab -> "Contact Us").
TROUBLESHOOTING
PROBLEM
There is no display on the computer.
SOLUTION
1. Remove the computer and verify that the wire from the computer is properly connected to the wire that comes from the front post.
2. Check if the batteries are correctly positioned and battery springs are in proper contact with batteries.
3. The batteries in the computer may be unresponsive. Change to new batteries.
The elliptical bike wobbles when in use.
The elliptical bike makes squeaking noise when in use.
Turn the adjustable end caps on the front and rear stabilizers as needed to level the elliptical bike. Some bolts on the elliptical bike might have become loose. Please inspect all the bolts and tighten any loosened bolts.
Version 1.1
16
EXPLODED DIAGRAM 1
17
EXPLODED DIAGRAM 2
18
PARTS LIST
No.
Description
Qt Spec.
y
1 Main Frame
1
2 Front Stabilizer
1
3 Rear Stabilizer
1
4 Front Post
1
5 Left Swing Rod
1
6 Right Swing Rod
1
7 Left Foot Bar
1
8 Right Foot Bar
1
9 Left Handlebar
1
10 Right Handlebar
1
11 Middle Handlebar
1
12 Foam Grip
24*30*500 2
13 Handrail End Cap
2
14 Handle Pulse Sensor
2
14a Handle Pulse Wire
L=750mm
1
15 Plug
12.1
1
16 Screw
ST4.2*20
2
17 Spring Washer
8
10
18 Bolt
M8*30
2
19 Clamp Cover
1
20 Computer
1
20a Computer Wire
1
21 Screw
M5*10
6
22 Cap
32*1.5
2
23 Foam Grip
31*41*675 2
24 Bolt
M8*43
4
25 Big Arc Washer
8*20*2.0
6
26 Nut
M8
15
27 Left Swing Rod Cover-A
1
28 Left Swing Rod Cover-B
1
Right Swing Rod
29
1
Cover-A
Right Swing Rod
30
1
Cover-B
No Description
.
31 Bolt 32 Big Washer 33 Shaft Sleeve 34 Wave Washer 35 Bushing 36 Shaft Sleeve 37 Insulation Casing 38 Left Foot Bar Cover-A 39 Left Foot Bar Cover-B 40 Right Foot Bar Cover-A 41 Right Foot Bar Cover-B 42 Screw 43 Square Cap 44 Bolt 45 Washer 46 Bolt 47 Bolt 48 Left Pedal 49 Right Pedal 50 Bolt 51 Small Alloy 52 Washer 53 Nut 54 U Bracket 55 Plastic Bushing 56 Shaft Sleeve 57 Left Pedal Bolt 58 Wave Washer 59 Spring Washer 60 Left Nylon Nut
Qt Spec.
y
M8*16
2
32*8*2.0 2
32*3.5
4
19*26*0.3 2
31.8*19.2 2
32*3
4
14*8.2*58 2
1
1
1
1
ST4.2*16
10
60*30
2
M8*75
2
8*16*1.5 17
M6*10
1
M8*50
4
1
1
M10*55
2
14*10*10 4
10*20*2.0 2
M10
2
2
32*20
4
4
16*89*L23 1
28*17*0.3 2
20*13*B2 2
1/2"
1
61 Right Pedal Bolt
16*89*L23 1
62 Right Nylon Nut
1/2"
1
19
No.
Description
63 Left Decorative Cover
64 Right Decorative Cover
65 Adjustable End Cap
66 Screw
67 Bolt
68 Bolt
69 Transportation Wheel
70 Screw
71 Tension Wire
72 Sensor Wire
73 Extension Sensor Wire
74 Bottle Holder
75 Tension Control Knob
75a Tension Control Wire
76 Big Arc Washer
77 Bolt
78 C-clip
79 Bearing
80 Wave Washer
81 Belt
82 Nut
83 Spring Washer
84 Screw
85 Belt Pulley
86 Left Belt Cover
87 Right Belt Cover
88 Crank Cover
89 Left Crank
90 Right Crank
91 Nut
92 Crank Cap
93 Screw
PARTS LIST
Spec.
ST4.2*20 M8*55 M8*40
M8*20 L=500mm L=1600mm L=1100mm
L=760mm 5*18*1.0 M5*55 20*1 6004ZZ 20*24*0.3 PJ400 M6 S10 6 M6*15 260
6.5" 6.5" M12*1.25
ST4.2*25
Qty
1 1 4 8 4 2 2 10 1 1 1 1 1 1 1 1 2 2 1 1 4 4 4 1 1 1 2 1 1 2 2 8
No.
Description
94 Screw
95 Washer
96 Shaft Snap Ring
97 Magnetic Plate Axle
98 Magnetic Bracket
99 Magnet Seat
100 Magnet
101 Screw
102 Spring
103 Bolt
104 Nut
105 Bolt
106 Washer
107 Bearing End Cover
108 Bearing Seat
109 Screw
110 Bearing
111 Flywheel
112 Idler Wheel Shaft
113 PC Pad
114 Screw
115 Idler Wheel
116 Bolt
117 Screw
118 Cover Limit Column
119 Plastic Washer
120 Shipping Tube
121 Allen Wrench
122 Allen Wrench
123 Spanner
124 Spanner
125 End Cap
Spec.
M6*15 6*16*1.2 12*1.0
ST2.9*9
M6*45 M6 M6*12 6*12*1.0
M6*12 6001 240
M8
M8*85 ST4.2*15
8*20*2.0
S6 S8 S10,13,14,15 S10,13,17,19
Qty
2 4 2 1 1 1 4 5 1 1 2 6 7 2 2 2 2 1 1 1 1 1 1 1 2 4 2 1 1 1 1 1
Version 1.0
20
21
Adobe PDF Library 11.0