Owner's Manual for MEAN WELL models including: LCM-60DA 60W Multiple Stage Constant Current Mode LED Driver Series, LCM-60DA, 60W Multiple Stage Constant Current Mode LED Driver Series, Multiple Stage Constant Current Mode LED Driver Series, Stage Constant Current Mode LED Driver Series, Constant Current Mode LED Driver Series, Current Mode LED Driver Series, Mode LED Driver Series, LED Driver Series, Driver Series
MEAN-WELL USA, INC. - РКС Компоненти - РАДІОМАГ
File Info : application/pdf, 8 Pages, 711.85KB
DocumentDocumentL C M - 6 0 D A 60W Multiple-Stage Constant Current Mode LED Driver
series
User's Manual
2 (for DA2-Type only)
(for DA-Type only)
AC Input: 200-240Vac (for DA2-Type only)
IS 15885(Part 2/Sec13)
THOMAS SAMUEL
THOMAS SAMUEL
R-41027766
(except for DA2-Type) (except for DA2-Type)
AUX
File Name:LCM-60DA-SPEC 2022-11-28
Downloaded from Arrow.com.
L C M - 6 0 D A 60W Multiple-Stage Constant Current Mode LED Driver
series
SPECIFICATION
MODEL
LCM-60 -
OUTPUT
CURRENT LEVEL
Current level selectable via DIP switch, please refer to"DIP SWITCH TABLE" section
500mA
600mA
700mA(default) 900mA
RATED POWER
60.3W
DC VOLTAGE RANGE
2 ~ 90V
2 ~ 90V
2 ~ 86V
2 ~ 67V
OPEN CIRCUIT VOLTAGE (max.) 95V
73V
CURRENT RIPPLE Note.5 5.0% max. @rated current
CURRENT TOLERANCE
±5%
AUXILIARY DC OUTPUT
Nominal 12V(deviation 11.4~12.6V)@50mA for AUX-Type only
SETUP TIME
Note.3 Note.9
500ms / 230VAC
VOLTAGE RANGE
180 ~ 295VAC 254 ~ 392VDC Note.2 (Please refer to "STATIC CHARACTERISTIC" section)
FREQUENCY RANGE
47 ~ 63Hz
POWER FACTOR (Typ.)
PF0.975/230VAC, PF0.95/277VAC@full load (Please refer to "POWER FACTOR (PF) CHARACTERISTIC" section)
1050mA 2 ~ 57V
1400mA 2 ~ 42V
INPUT
TOTAL HARMONIC DISTORTION
THD< 20%(@load75%) (Please refer to "TOTAL HARMONIC DISTORTION(THD)" section)
EFFICIENCY (Typ.) Note.4 92%
AC CURRENT (Typ.) INRUSH CURRENT (Typ.)
0.32A/230VAC 0.27A/277VAC COLD START 20A(twidth=270s measured at 50% Ipeak) at 230VAC; Per NEMA 410
MAX. No. of PSUs on 16A CIRCUIT BREAKER
25 units (circuit breaker of type B) / 32 units (circuit breaker of type C) at 230VAC
LEAKAGE CURRENT
<0.5mA / 240VAC
STANDBY POWER CONSUMPTION Note.6
<0.5W for Blank-Type, <1.2W for AUX-Type
SHORT CIRCUIT
Constant current limiting, recovers automatically after fault condition is removed
PROTECTION OVER VOLTAGE
105 ~ 125V Shutdown o/p voltage, re-power on to recover
OVER TEMPERATURE
Shutdown o/p voltage,re-power on to recover
DIMMING FUNCTION SYNCHRONIZATION
TEMP. COMPENSATION WORKING TEMP.
Please refer to "DIMMING OPERATION" section Please refer to "SYNCHRONIZATION OPERATION" section By external NTC, please refer to "TEMPERATURE COMPENSATION OPERATION"section Tcase=-30 ~ +90 (Please refer to " OUTPUT LOAD vs TEMPERATURE" section)
MAX. CASE TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT
Tcase=+90 20 ~ 90% RH non-condensing -40 ~ +80, 10 ~ 95% RH ±0.03%/ (0 ~ 50)
VIBRATION SAFETY STANDARDS
10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
UL8750(except for DA2-Type), CSA C22.2 No.250.13-12, ENEC BS EN/EN61347-1, BS EN/EN61347-2-13, BS EN/EN62384 independent,GB19510.14, GB19510.1,BIS IS15885(except for DA2-Type), EAC TP TC 004 approved; According to BS EN/EN61347-2-13 appendix J suitable for emergency installations(EL)(AC Input: 200-240Vac)(for DA2-Type only)
SAFETY & EMC
DALI STANDARDS WITHSTAND VOLTAGE ISOLATION RESISTANCE
IEC62386-101, 102, 207,251 I/P-O/P:3.75KVAC; I/P-DA:1.5KVAC; O/P-DA:1.5KVAC I/P-O/P:>100M Ohms / 500VDC / 25/ 70% RH
EMC EMISSION Note.7
Compliance to BS EN/EN55015, BS EN/EN61000-3-2 Class C(@load40%) ; BS EN/EN61000-3-3; GB17625.1,GB17743, EAC TP TC 020
EMC IMMUNITY
Compliance to BS EN/EN61000-4-2,3,4,5,6,8,11, BS EN/EN61547, light industry level(surge immunity Line-Line 2KV), EAC TP TC 020
MTBF
2270.7K hrs min. Telcordia SR-332 (Bellcore) ; 193.7K hrs min. MIL-HDBK-217F (25)
OTHERS DIMENSION
123.5*81.5*23mm (L*W*H)
PACKING
0.24Kg ; 54pcs/15Kg/1.12CUFT
NOTE
~
, https://www.meanwell.com/serviceDisclaimer.aspx
Downloaded from Arrow.com.
File Name:LCM-60DA-SPEC 2022-11-28
L C M - 6 0 D A 60W Multiple-Stage Constant Current Mode LED Driver
series
BLOCK DIAGRAM
PFC fosc : 60KHz PWM fosc : 80KHz
EMI FILTER
I/P
&
RECTIFIERS
PFC CIRCUIT
POWER SWITCHING
PFC CONTROL
O.L.P. O.T.P.
PWM CONTROL
RECTIFIERS
RECTIFIERS &
FILTER
CURRENT LIMIT
DETECTION CIRCUIT
O.V.P.
+12Vaux (optional)
+V
-V
MCU
DA+ DA-
DIP SWITCH TABLE
LCM-60DA/DA2 is a multiple-stage constant current driver, selection of output current through DIP switch is exhibited below.
Io
DIP S.W. 1 2 3 4 5 6
500mA
---- ---- ---- ---- ---- ----
600mA
ON ---- ---- ---- ---- ----
700mA(factory default) ON ON ---- ---- ---- ----
900mA
ON ON ON ---- ---- ON
1050mA
ON ON ON ON ---- ON
1400mA
ON ON ON ON ON ON
Note: For more current setting,please contact MW's sales.
Downloaded from Arrow.com.
File Name:LCM-60DA-SPEC 2022-11-28
L C M - 6 0 D A 60W Multiple-Stage Constant Current Mode LED Driver
series
DIMMING OPERATION
LCM-60DA
DADA+ PUSH AC/N AC/L
Push Button AC/N AC/L
LCM-60DA2
DADA+
AC/N AC/L
PUSH dimming(primary side)
Action Short push Long push Reset
Action duration
Function
0.1~1 sec.
Turn ON-OFF the driver
1.5~10 sec.
Every Long Push changes the dimming direction, dimming up or down
>11 sec.
Set up the dimming level to 100%
The factory default dimming level is at 100%. If the push action lasts less than 0.05 sec., it will not lead to a change for the status of the driver. Up to 10 drivers can perform the PUSH dimming at the same time when utilizing one common push button. The maximum length of the cable from the push button to the last driver is 20 meters. The additive push button can be connected only between the PUSH terminal, as displayed in the diagram,
and AC/L (in brown or black); it will lead to short circuit if it is connected to AC/N.
DALI interface(primary side; for DA/DA2-Type)
Apply DALI signal between DA+ and DADALI protocol comprises 16 groups and 64 addresses. First step is fixed at 6% of output.
Push Button AC/N AC/L
Downloaded from Arrow.com.
File Name:LCM-60DA-SPEC 2022-11-28
Output Current (%)
+ + + + + +
L C M - 6 0 D A 60W Multiple-Stage Constant Current Mode LED Driver
series
SYNCHRONIZATION OPERATION
Synchronization up to 10 drivers (1 master + 9 slaves) Dimming operating range : 10%~100% Sync cable length : < 5m Sync cable type : Flat cable Sync cable cross section area : 22 24 AWG (0.2~0.3mm2)
LCM-60DA/DA2 (Slave 2)
SYN. --
LCM-60DA/DA2 (Master)
SYN. --
LCM-60DA/DA2 (Slave 1)
SYN. --
5m
5m
NOTE: 1. Please make sure all units are set to 100% dimming setting (factory default) before synchronizing. 2. Min. Dimming operating range depends on dimmer setting.
TEMPERATURE COMPENSATION OPERATION
LCM-60DA/DA2 have the built-in temperature compensation function ; by connecting a temperature sensor (NTC resistor) between the +NTC / -NTC terminal of LCM-60DA/DA2 and the detecting point on the lighting system or the surrounding environment, output current of LCM-60DA/DA2 could be correspondingly changed, based on the sensed temperature, to ensure the long life of LED.
NTC derating curve
105
100
95
222200KKO 333300KKO
90
447700KKO
85
80
75
70
65
55
60
65
70
75
80
85
90
95
Sensed Temperature()
LCM-60DA/DA2 can still be operated normally when the NTC resistor is not connected and the value of output current will be the current level selected through the DIP switch. NTC reference:
NTC resistance
Output Current
220K
< 60, 100% of the rated current (corresponds to the setting current level) > 60, output current begins to reduce, please refer to the curve for details.
330K
< 70, 100% of the rated current (corresponds to the setting current level) > 70, output current begins to reduce, please refer to the curve for details.
470K
< 80, 100% of the rated current (corresponds to the setting current level) > 80, output current begins to reduce, please refer to the curve for details.
Notes: 1. MEAN WELL does not offer the NTC resistor and all the data above are measured by using THINKING TTC03 series.
2. If other brands of NTC resistor is applied,please check the temperature curve first. Dimming and synchronization function of the driver will be invalid when the "temperature compensation" function is in use.
File Name:LCM-60DA-SPEC 2022-11-28
Downloaded from Arrow.com.
LOAD (%)
L C M - 6 0 D A 60W Multiple-Stage Constant Current Mode LED Driver
series
OUTPUT LOAD vs TEMPERATURE
100 Others
80
60
40
1050mA/1400mA
20
-30 -15
0
15
30
40
50 60
AMBIENT TEMPERATURE,Ta ()
70 (HORIZONTAL)
LOAD (%)
100 80 60 40 20
-30 -25 0
20
45
55
65
75
90 (HORIZONTAL)
Tcase ()
STATIC CHARACTERISTIC
LOAD (%)
100 90 80 70 60 50 40
180 190 200 210 220 230 240 250 260 270 280 295
INPUT VOLTAGE (V) 60Hz De-rating is needed under low input voltage.
Downloaded from Arrow.com.
File Name:LCM-60DA-SPEC 2022-11-28
THD
L C M - 6 0 D A 60W Multiple-Stage Constant Current Mode LED Driver
series
TOTAL HARMONIC DISTORTION (THD)
Tcase at 80
60%
50%
40%
500mA
30%
600mA
700mA
20%
900mA
10%
1050mA
1400mA
0%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD (230Vac Input)
POWER FACTOR (PF) CHARACTERISTIC
Tcase at 80
THD
80%
70%
60%
50%
500mA
40%
600mA
30%
700mA
900mA
20%
1050mA
10%
1400mA
0%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD (277Vac Input)
PF
1.00
0.97
0.94
0.91
500
0.88
600
0.85
700
0.82
900
0.79
1050
0.76
1400
0.73
0.70
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% (60W)
LOAD (230Vac Input)
PF
1.00 0.97 0.94 0.91 0.88 0.85 0.82 0.79 0.76 0.73 0.70 0.67 0.64 0.61 0.58 0.55 0.52 0.49
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% (60W)
LOAD (277Vac Input)
EFFICIENCY vs LOAD
LCM-60DA series possess superior working efficiency that up to 91% can be reached in field applications. Tcase at 80
500 600 700 900 1050 1400
95.0%
90.0%
85.0%
80.0%
500
75.0%
600
70.0%
700
900
65.0%
1050
60.0%
1400
55.0%
50.0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD (230Vac Input)
EFFICIENCY (%)
95.0%
90.0%
85.0%
80.0%
75.0%
500
70.0%
600
65.0%
700
60.0%
900
55.0%
1050
50.0%
1400
45.0%
40.0%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
LOAD (277Vac Input)
File Name:LCM-60DA-SPEC 2022-11-28
EFFICIENCY (%)
Downloaded from Arrow.com.
81.5
6.75
23 4
L C M - 6 0 D A 60W Multiple-Stage Constant Current Mode LED Driver
series
MECHANICAL SPECIFICATION
123.5
6.75
110
Case No.LCM-60A Unit:mm
2-4.2 6.75
68
6.75
1
2
3
TB1
4
5
1
2
SYN.
3 4
1 2
CN101
TB3
3 4
CN100
1 2 TB5
ON
123 456
LCM-60DA
39.3 7.8
65.5
7.8 2-4
Terminal Pin No. Assignment( TB1)(LCM-60DA)
Pin No. Assignment Pin No. Assignment
1
AC/L
4
DA+
2
AC/N
5
DA-
3
PUSH
Terminal Pin No. Assignment( TB1)(LCM-60DA2)
Pin No. Assignment Pin No. Assignment
1
AC/L
4
DA-
2
AC/N
3
DA+
1
2
3
TB1
4
1
2
SYN.
3 4
1 2
CN101
LCM-60DA2
TB3
3 4
CN100
1 2 TB5
ON
123 456
15
tc
40
Terminal Pin No. Assignment(TB3)
Pin No. Assignment Pin No.
1
+FAN(+AUX)
3
2
-FAN(-AUX)
4
Assignment +NTC -NTC
Bottom View
tc : Max. Case Temperature
Pin1(+FAN) / Pin2(-FAN) is the Auxiliary DC output for the optional model LCM-60DA-AUX; it can be used to drive fan.
Terminal Pin No. Assignment(TB5)
Pin No. Assignment
1
+V
2
-V
SYN. Connector(CN101/CN100):JST B2B-XH or equivalent
Pin No. Assignment Mating Housing
Terminal
1,3
+
JST XHP
JST SXH-001T-P0.6
2,4
-
or equivalent
or equivalent
Installation Manual
Please refer to : http://www.meanwell.com/manual.html
Downloaded from Arrow.com.
File Name:LCM-60DA-SPEC 2022-11-28