User Guide for HOLMAN models including: HOLMAN, 2 Dial, Tap Timer, CO1601
Tim e r. U s e r G u id e. CO1601 w w w .ho lm a n in d u strie. s.c om.a u. GLOSSARY. A. UNIVERSAL TAP ADAPTOR. B. TAP CONNECTION. C. UNION NUT.
2 Dial Tap Timer User Guide CO1601 GLOSSARY A A. UNIVERSAL TAP ADAPTOR B B. TAP CONNECTION C. UNION NUT C D. CONTROL DIALS E. BATTERY COMPARTMENT D F. CLEAR SCREW-ON COVER G. SNAP-ON HOSE CONNECTION F INSTALLATION Make sure the washer is in place, then screw the 2 Dial Tap Timer to the tap. E G Turn it clockwise (hand tighten only). There should be no need to use thread seal tape, as long as the tap seals onto the washer www.holmanindustries.com.au BATTERY INSTALLATION 1. Hold the Tap Timer with the battery compartment facing you 2. Remove the BATTERY COMPARTMENT tray 3. Connect a 9V alkaline battery to the battery connector 4. Insert the connected battery and push E in the BATTERY COMPARTMENT tray When changing a battery, the Tap Timer will hold the current program if you fit the battery within 2 minutes. When changing the battery, make sure the battery compartment stays dry Use only 9V alkaline batteries SIMPLE 3 STEP PROGRAMMING How to set run time and watering interval. Press ENTER to reference the start time. The Tap Timer will not run immediately after program is set. Program will commence after chosen interval duration has lapsed 1. Turn the LEFT dial to select RUN TIME. Select from 2 minutes to 240 minutes RUN TIME INTERVAL 30 15 60 10 120 5 240 Mins 2 OFF 3rd Day 48Hr 4th Day 24Hr 5th Day 12Hr 6Hr 7th Day MAN ENTER 2. Turn the RIGHT dial to select the INTERVAL. Select from every 6 hours to every 7 days RUN TIME INTERVAL 30 15 60 10 120 5 240 Mins 2 OFF 3rd Day 48Hr 4th Day 24Hr 5th Day 12Hr 6Hr 7th Day MAN ENTER PROGRAMMING CONT. 3. Push ENTER the red LED will appear solid for three seconds to confirm your section. Watering will start at the selected interval The time that the ENTER button is pushed is used as a reference start time. To change the program, simply follow the same three steps RUN TIME INTERVAL 30 15 60 10 120 5 2 240 Mins OFF 3rd Day 48Hr 4th Day 24Hr 5th Day 12Hr 6Hr 7th Day MAN ENTER MANUAL START 1. Turn the LEFT dial to select RUN TIME 2. Turn the RIGHT dial to MAN 3. Press ENTER Running a manual run time will not change any program previously entered. Watering will begin and end at selected run time. No need to move the dials RUN TIME INTERVAL 30 15 60 10 120 5 2M4in0s 2 OFF 3rd Day 48Hr 4th Day 24Hr 5th Day 12Hr 6Hr 7th Day MAN ENTER RUN TIME INTERVAL 30 15 60 10 120 5 240 Mins 2 OFF ENTER 3rd Day 48Hr 4th Day 24Hr 5th Day 12Hr 6Hr 7th Day MAN RUN TIME INTERVAL 30 15 60 10 120 5 2M4in0s 2 OFF 3rd Day 48Hr 4th Day 24Hr 5th Day 12Hr 6Hr 7th Day MAN ENTER STOP OR NO WATERING 1. Turn the RUN TIME dial to the OFF position. While the RUN TIME dial is in the OFF position no watering will happen To re-commence a pre-set program, move the RUN TIME dial to any other position RUN TIME 30 15 60 10 120 5 240 Mins 2 OFF INTERVAL 3rd Day 48Hr 4th Day 24Hr 5th Day 12Hr 6Hr 7th Day MAN ENTER RED LED - OPERATING STATES 1. SOLID for three seconds: Confirms program and each time the auto program is changed 2. FLASHING every 30 seconds: All is running correctly 3. FLASHING every one second: Battery needs changing EXTRA WATERING CYCLES The manual operation mention previously can be used for running an extra cycle whilst the timer is programmed. The manual cycle will run immediately after the ENTER button is pressed. The Tap Timer will resume the automatic program once the manual time has elapsed. FAULT FINDING 1. Ensure your tap is turned on 2. Ensure your battery is in good condition. Use only 9V alkaline battery When the Tap Timer is not using an automatic program, it must be in the OFF position. Turn the tap OFF when the Tap Timer is not in watering mode CLEARING MEMORY To clear an existing program, remove the battery and wait until the Tap Timer resets. (This can take up to 5 minutes.) Alternatively, remove the battery and initiate a manual start which will clear the memory immediately. TECHNICAL DATA PRODUCT: Holman 2 Dial Tap Timer PRODUCT CODE: CO1601 MAXIMUM WATER PRESSURE: 600 kPa MINIMUM WATER PRESSURE: 100 kPa BATTERY: Use a standard 9V alkaline battery FLUID: Only use cold water with NO added chemicals FREQUENCY OPTIONS: Every 6 hours, 12 hours, 24 hours, 48 hours, Every 3rd Day, Every 4th Day, Every 4th Day, Every 7th Day RUN TIME OPTIONS: 2, 5, 10, 15, 30, 60, 120 or 240 minutes. We really appreciate having you as a customer, and would like to say thank you for choosing us. Should you have any questions about this product or its operation please call customer service on 1300 716 188 Head Office/Service 11 Walters Drive, Osborne Park WA 6017 Tel: +61 8 9416 9999 Fax: +61 8 9416 9920 support@holmanindustries.com.au www.holmanindustries.com.au Copyright © 2020 Holman IndustriesAdobe PDF Library 15.0 Adobe InDesign 16.0 (Macintosh)