User Manual for Quantex Smart TECHNOLOGY models including: QTUF80EV 2BB7Q, QTUF80EV 2BB7QQTUF80EV, QTUF80EV, QTUF80EV Home EV Wallbox, Home EV Wallbox, EV Wallbox, Wallbox
QUANTEX SMART TECHNOLOGY LTD QTUF80EV 2BB7Q-QTUF80EV 2BB7QQTUF80EV qtuf80ev
File Info : application/pdf, 25 Pages, 1.27MB
DocumentDocumentHome EV Wallbox User manual Version: V1.2 1 CONTENT 1 Warranty 2 Safety and Warning 3 Introduction 3.1 Product Technical Specifications 3.2 External Structure 3.3 Package Contents 4 Configuration and Operation 4.1 Power-on Checking 4.2 Start and stop charging station by your charge card 4.3 Start and stop charging station by APP(Bluetooth) 5 Set up and update 5.1 Mode setting for maximum charging current 5.2 External enabling/disabling of the Wallbox 5.3 Firmware version upgrade 6 Troubleshooting 6.1 Indicator Status 6.2 Fault Code and Resolution(LCD display) 6.3 Fault Code and Resolution(LED display) 2 Warranty QUANTEX SMART ENERGY. (Hereinafter "QSE") warrants that Products supplied to Customer pursuant to this Agreement/Contract shall be of merchantable quality and shall meet all applicable safety standards and free from any defect of design, material and workmanship within the warranty period. The warranty period is Twenty-four (24) months since from the delivery date. QSE warranty does not cover damages resulting from inappropriate storage, incorrect installation, improper operation or bad environment beyond environmental requirement. Customer gives notice in writing within a period of ten (10) days after Customer has discovered that some or all Products do not comply with the warranty as set out in this warranty. Customer shall provide necessary assistance to QSE for failure detection. QSE gives response within a reasonable time of 48 hours. QSE shall analyze the fault reason and provide technical instruction for Customer to repair Products. Customer repairs Products and applies for free spare parts from QSE in case replacements are required. A written claim report about fault description, serial number of Products, photos of Products and applied spare parts must be sent to QSE for verification. QSE shall not accept the claim if modifications or reworking have been performed to Products without QSE's consent. Spare parts are offered for free within the warranty period. Beyond warranty period, spare parts are offered at Customer's cost. Faulted parts replaced by Customer shall be well stored and packaged with markings of fault description for further disposal by QSE. The faulted parts after repair and test can be treated as spare part to Customer. No local service is provided for free and QSE charges service fee for local service according the following standards: USD100 (USD One Hundred Only) per person per day plus the actual travel costs and material costs. A mutual agreement should be reached before offering local service. Except as set forth herein, QSE provides no other warranty, whether express or implied. The warranty applies only to Products which are supplied by QSE and are used out of Mainland China. 3 1 Safety and Warning Save these instructions. Read all instruction before installing or using the charger. 1Keep the charger away from explosive or flammable materials, chemicals, vapors and other hazard objects. 2Keep the charger socket clean and dry. If it gets dirty, please wipe it with clean dry cloth. 3Touching the socket core is strictly forbidden when power on. 4Do not use the charger in case of any device defects, crack, abrasion, bare leakage and so on. Please contact the professional personnel if any of these conditions occurs. 5Do not attempt to dissemble, repair, refit the charger. If necessary, please contact the professional personnel. Improper operation will result in device damage, electric leakage, etc. 6In case any abnormal condition happens, please cut off all input and output power supplies immediately. 7Please protect charging carefully from rain and lightening. 8Keep children away from the charger. 9During charging, do not drive the EV Charge only when the EV is stationary,for hybrid cars, charge only when the engine is switched off. 10) Our packaging materials are environmentally friendly and can be recycled. Please put the packaging in applicable containers to recycle it. Do not dispose of this device with the household waste. It should be taken to a suitable facility for recycling of electrical and electronic devices. For more detailed information about recycling of this device, please contact your local city/town council office or your household waste disposal service. The input and output voltages of this device are high voltage, which threaten human life safety. Please strictly observe all warnings on the device and user manual. Unauthorized and non-professional service personnel are forbidden to remove the cover of this device. 4 2 Introduction 2.1 Product Technical Specifications Model Technical features Charging capacity Input/Output power RCD Standby power QTUF40EV QTUM40EV QTUY40EV QTUF48EV QTUM48EV QTUY48EV QTUF60EV QTUM60EV QTUY60EV Up to 9.6.5KW Up to 12KW 85-265VAC-50/60Hz40A-1phase 85-265VAC-50/60Hz48A-1phase 30Ma RCD Type A and DC 6Ma RCD function <3W Up to 14.4KW 85-265VAC-50/60Hz60A-1phase Measuring accuracy 1% Communication User interface Bluetooth/WIFI(Optional) APP LED/LCD(3.5')/ RFID(Mifare ISO& IEC 14443A) Input Plug NEMA 14-50(Optional) Certificate Charging Interface NEC 625, SAE J1772, UL 817, UL 991, UL 2231, UL 225, and UL 2594. SAE J1772 40A 5M SAE J1772 48A 5M SAE J1772 60A 5M Special Protection Physical properties Warranty Protection Enclosure Front Panel Special Protection Installation Cooling Operating temperature Over current protection, Residual current protection, Ground protection, Surge protection, Over/Under voltage protection, Over/Under temperature protection 2 years IP54, IK10 Plastic PC940/ Galvanized steel Temper glass Over current protection, Residual current protection, Ground protection, Surge protection, Over/Under voltage protection, Over/Under temperature protection Wall-mount/Pole-mount Natural cooling -30 to +55 Humidity Product Dimensions Package Dimension Max.95%(non-regulating) 320*230*100(L*W*H)mm 465*325*270(L*W*H)mm 5 Net Weight Gross Weight Model Technical features Charging capacity Input/Output power RCD Standby power Measuring accuracy Communication User interface Input Plug Certificate Charging Interface Special Protection Physical properties Warranty Protection Enclosure Front Panel Special Protection Installation Cooling Operating temperature Humidity Product Dimensions Package Dimension Net Weight Gross Weight 5.5Kg 6.2Kg QTUF80EV QTUM80EV QTUY80EV 5.8Kg 6.5Kg 7Kg 7.5Kg Up to19.2KW 85-265VAC-50/60Hz80A-1phase 30Ma RCD Type A and DC 6Ma RCD function <3W 1% Bluetooth/WIFI(Optional) APP LED/LCD(3.5')/ RFID(Mifare ISO& IEC 14443A) NEMA 14-50(Optional) NEC 625, SAE J1772, UL 817, UL 991, UL 2231, UL 225, and UL 2594. SAE J1772 80A 5M Over current protection, Residual current protection, Ground protection, Surge protection, Over/Under voltage protection, Over/Under temperature protection 2 years IP54, IK10 Plastic PC940/ Galvanized steel Temper glass Over current protection, Residual current protection, Ground protection, Surge protection, Over/Under voltage protection, Over/Under temperature protection Wall-mount/Pole-mount Natural cooling -30 to +55 Max.95%(non-regulating) 320*230*100(L*W*H)mm 465*325*270(L*W*H)mm 8.2Kg 8.7Kg 6 2.2 External Structure 2.3 Package Contents Unpack the product. Please check and verify following items after receiving the charger : Visual inspection on charger's external appearance. If there is any breakage or other damage,please notify the seller immediately. Check type and quantity of all accessories as follows. If there is a shortage in the quantity of any item or if any items are missing, please contact the seller at once. 7 User Manual (x1) 6 Expansion Pipe (x6) M4*40 Screw Installation cardboard (x6) (x1) Wallbox(x1) The holder (x1) RFID CARD (x2) Key (x2) 3 Operation Instruction 3.1 Installation Preparation 1) Tools required Tool Name Photo Multimeter Function Check electrical connection and electrical parameter Cross Screwdriver (PH2x150mm, PH3x250mm) Tighten the screws 8 Insulated Torque Wrench Electric drill Diagonal Pliers Tighten the bolts Hole on the wall Cut cables 2) Cables & Materials Name Power supply cable Specification Single-phase or three-phase power supply cable Quantity Depend on actual requirement 3.2 Installation Process 1) Installation Notice Electrical devices should only be installed, operated, and maintained by qualified personnel. No responsibility is assumed by the manufacturer for any consequences arising out of the use of this device. A qualified person is one who has certified skills and knowledge related to the construction, installation and operation of this type of electrical device and who has received safety training to recognize and avoid the hazards involved. All applicable local, regional, and national regulations must be applied when installing, repairing and maintaining this device. RCD of the charger is intergrated 6mA DC, please install a Type A breaker outside. 2) Checks before starting the Installation Process Ensure the charger's location allows good operational access for normal use and repair & maintenance. The AC input components within the premise's power supply are correctly fitted with required protection items prior to installation of the charger. 9 3) Installation Procedure 1. Please use a percussion drill to drill holes according to the cardboard positioning 2. Install expansion bolts(3*M6*60MM) 10 3. Open the cover with the key,fix the charging station with self=tapping screws(3*M5*50mm) 4. Use a cable with a size of 3*10AWG(32A)/ 3*9AWG(40A)/ 3*8AWG(48A)to connect to the input terminal of the charging station, from left to right,N / L and PE wire, and then tighten the screw with a screwdriver. 11 5. Fix the hook on the wall with screws (3*M5*50mm) 6. Lock the cover and start to test and charge 12 4 Configuration and Operation 4.1 Power-on Checking Please check / re-check the following items prior to initial Power-on : The charger's location allows good operational access to normal use and repair & maintenance. The AC input components within the premise's power supply are fitted correctly with required protection items prior to installation of the charger. Double confirm the charger is installed properly. No components or other items have been left on the top of the charger. 4.2 Start and stop charging station by your charge card Start charging 1. Plug charging cable into your car and LED ring turns yellow. 2. Hold your charge card (RFID Card) in front of the reader, marked with icon waiting 3 seconds. 3. reacts with a beep,LED ring turns green(Breathing state) when it starts charging. Stop charging 1. Hold your charge card (RFID Card) in front of the reader, marked with icon waiting 3 seconds. 2. reacts with a beep,LED ring turns green when it stops charging. 3. Unplug charging cable from your car and place the charging cable back into cable holder. 13 4.3 Start and stop charging station by APP(Bluetooth) Step1-Download the APP"QT EV"from APP store or Google paly Step 2-Click the Bluetooth icon to enter the interface of binding the device 14 Step 3-Connect the wallbox Click Note: 1,The number is the charging station number that at the bottom right of the LCD display. 2,The initial password is 123456. After the device is successfully connected, the password can be changed. Note: 1, Make sure there is a display (connectable) behind the device number. 2, Click on the device number, wait for about 10S to enter the next interface. 3, If you do not enter the next interface, please turn off the Bluetooth of your phone and wait for 3S to turn on the Bluetooth of your phone again, and repeat the second step. 15 Step 4-Connect your ev car with the charger gun and start charging 16 Step 5-Modify the charging station key by APP(Bluetooth) Click Note: If you forget the modified device password, you can repeatedly quickly press the emergency stop button on the right side of the charging station 4 times (press it down and reset clockwise once, and it will be completed within 3 seconds) to restore the factory settings password. 17 Step 5-Start charging at the appointment time by APP(Bluetooth) 1Click 3Click 2Click Note: 1. Click the set time button and select the time to start charging. 2. Click the button to start charging, and confirm to start charging at a predetermined time. 18 Step 6-Load balancing setting by APP(Bluetooth) Load balancing needs a power-sampling device on the incoming mains supply cables, which could be a power meter or a current transducer and normally located in the meter box. Set your maximum overload current through the APP according to the fuse capacity of your household's total incoming line 19 Step 7-Charging history view by APP(Bluetooth) Click By viewing the charging history, you can clearly understand the daily or monthly charging time and charge level of your charging station. 20 5 Set up and update 5.1 Mode setting for maximum charging current 5.3 Firmware version upgrade This product can update the firmware software of the product through the Micro SD Card. The user puts the firmware that needs to be updated into the Micro SD Card through the computer, and then powers off the charging station, and inserts the Micro SD Card into the SD card slot as shown above. Restart the charging station. When the software version in the lower right corner of the LCD display is updated, it means that the firmware of the charging station has been updated. Then remove the Micro SD Card. 21 6 Troubleshooting 6.1 Indicator Status What you see What it means What to do LED ring off or green LED ring yellow LED ring green breathing LED ring green LED ring red is ready for use. charging cable connected the car successfully is charging the car The car is fully charged. is experiencing an error Plug charging cable into the car Hold your charge card (RFID Card) in front of the reader The car is charging. Unplug charging cable from your car and place the charging cable back into cable holder. Check the troubleshooting chapter in this manual for solutions. 22 6.2 Fault Code and Resolution(LCD display) Display indication When a problem occurs, error messages are often shown on the display. With this information you can quickly identify and investigate the problem. Fault names Over voltage Under voltage Over current EPO fault Over Leakage NE fault Possible reason AC input voltage may be too high AC input voltage may be too low AC input current may be too big The emergency stop button is pressed leakage current to earth may be too high Input/output imperfect earth or inverse connection for L/N wires Troubleshooting suggestion 1. Check the input voltage from background monitoring data 2. If the voltage is over 480Vac in short timewait till power grid recover to normal voltage range or Power off and restart 3. If the fault can not be removed,please contact to us 1. Check the input voltage from background monitoring data 2. If the voltage is under 140Vac in short timewait till power grid recover to normal voltage range or Power off and restart 3. If the fault can not be removed,please contact to us 1. Shut off distribution cabinet leakage/over current protection switch immediately 2. Check whether there is low resistance connection between two AC output wires 3. Eliminate above reasons,connect on power again,if the fault keep on,please contact to us 1. Reset emergency stop button(On the right side of the charging station) 1. Shut off distribution cabinet leakage/over current protection switch immediately 2. Check whether there is broken of AC output wires or low resistance connection to earth 3. Eliminate above reasons,connect on power again,if the fault keep on,please contact to us 1. Shut off distribution cabinet leakage/over current protection switch immediately 2. Check AC input/output wires if be normal,or if inverse connection input with L/N wires 3. Eliminate above reasons,connect on power again,if the fault keep on,please contact to us 23 6.3 Fault Code and Resolution(LED display) Display indication When a problem occurs, error messages are often shown on the display. With this information you can quickly identify and investigate the problem. Fault number 0001 0002 0003 0004 0005 0006 Possible reason The emergency stop button is pressed AC input voltage may be too high AC input voltage may be too low AC input current may be too big leakage current to earth may be too high Input/output imperfect earth or inverse connection for L/N wires Troubleshooting suggestion 1. Reset emergency stop button(On the right side of the charging station) 1. Check the input voltage from background monitoring data 2. If the voltage is over 480Vac in short timewait till power grid recover to normal voltage range or Power off and restart 3. If the fault can not be removed,please contact to us 1. Check the input voltage from background monitoring data 2. If the voltage is under 140Vac in short timewait till power grid recover to normal voltage range or Power off and restart 3. If the fault can not be removed,please contact to us 1. Shut off distribution cabinet leakage/over current protection switch immediately 2. Check whether there is low resistance connection between two AC output wires 3. Eliminate above reasons,connect on power again,if the fault keep on,please contact to us 1. Shut off distribution cabinet leakage/over current protection switch immediately 2. Check whether there is broken of AC output wires or low resistance connection to earth 3. Eliminate above reasons,connect on power again,if the fault keep on,please contact to us 1. Shut off distribution cabinet leakage/over current protection switch immediately 2. Check AC input/output wires if be normal,or if inverse connection input with L/N wires 3. Eliminate above reasons,connect on power again,if the fault keep on,please contact to us 24 FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.Microsoft Word 2016 Microsoft Word 2016