Instruction Manual for apuro models including: FC374-A, FC375-A, FC376-A, FC377-A, FC374-A Heavy Duty Fryer, FC374-A, Heavy Duty Fryer
Model: FC374-A / FC375-A / FC376-A / FC377-A Heavy Duty Fryer Instruction manual FC374-A to FC377-A A5 v2 20210715 1 2021/7/15 11:49
Media.nisbets.com View all Health › Url: https://media.nisbets.com/asset/au/media/user manual fc374-a fc375-a fc376-a fc377-a
File Info : application/pdf, 12 Pages, 1.70MB
DocumentDocumentHeavy Duty Fryer Instruction manual Model: FC374-A / FC375-A / FC376-A / FC377-A '$"UP'$"@"@W@JOEC AU Telephone Helpline: 1300225960 Safety Instructions · DO NOT cover the oil pan · Position on a flat, stable when frying. surface. · DO NOT immerse the · A service agent/qualified appliance in water. technician should carry out · Some surfaces become installation and any repairs if hot during operation - required. Do not remove any take care when using the components on this product. appliance. · Consult Local and National · Always switch off and Standards to comply with the disconnect the power supply following: to the appliance when not in - Health and Safety at Work use. Legislation · Not suitable for outdoor use. - Fire Precautions · This appliance must only - Wiring Regulations be used in accordance with - Building Regulations these instructions and by · ALWAYS ensure oil levels are persons competent to do so. within the `MIN' and `MAX' · Keep all packaging away levels. Failure to do so could from children. Dispose of result in fire. the packaging in accordance · ALWAYS use a suitable to the regulations of local cooking oil. authorities. · ALWAYS remove excess · If the power cord is moisture/water from food damaged, it must be before frying to avoid excess replaced by an Apuro agent foaming and spitting of the or a recommended qualified oil. technician in order to avoid a · Change oil regularly. The hazard. flashpoint of oil (the point · DO NOT use jet/pressure at which it ignites) gradually washers to clean the reduces the more it is used. appliance. 2 '$"UP'$"@"@W@JOEC Telephone Helpline: 1300225960 AU · This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. · Children should be supervised to ensure that they do not play with the appliance. · Apuro recommend that this appliance should be periodically tested (at least annually) by a Competent Person. Testing should include, but not be limited to: Visual Inspection, Polarity Test, Earth Continuity, Insulation Continuity and Functional Testing. · Ensure oil levels are maintained above the minimum level. Failing to do so may result in element failure. · Apuro recommend that this product is connected to a circuit protected by an appropriate RCD (Residual Current Device) (for FC376-A/FC377-A). Introduction Please take a few moments to carefully read through this manual. Correct maintenance and operation of this machine will provide the best possible performance from your Apuro product. These appliances are intended to be used for commercial applications, for example in kitchens of restaurants, canteens, hospitals and in commercial enterprises such as bakeries, butcheries, etc., but not for continuous mass production of food. Apuro will not accept liability for product failures in the event that: · The instructions in this manual have not been followed correctly. · Unqualified or unauthorized personnel have adjusted the Fryer. · Non-original spare parts are used. · The Fryer has not been handled and cleaned correctly. · The Fryer has been used for a purpose for which it was not intended. Pack Contents The following is included: · Apuro fryer · Basket (FC375-A/FC377-A x 2) · Element guard (FC375-A/FC377-A x 2) · Lid (FC375-A/FC377-A x 2) · Instruction manual Apuro prides itself on quality and service, ensuring that at the time of packaging the contents are supplied fully functional and free of damage. Should you find any damage as a result of transit, please contact your Apuro dealer immediately. Installation · Remove the Fryer from the packaging, ensuring that all protective packaging, plastic and residues are thoroughly cleaned from its surfaces. · Place the Fryer on a firm level surface (Or Fryer stand if purchased). · Before installing and operating the Fryer, it is the user's responsibility to ensure that all Health & Safety regulations concerning safe positioning, spacing, ventilation, electrical installation, and fire risk, are complied with. 3 '$"UP'$"@"@W@JOEC AU Fitting head unit to the Fryer body 1. Position the head unit onto the body of the fryer, locating it into the hole (A) at the side of the main body by the pin (B) on the side of the head unit. 2. Rotate the head unit and put spring pin (C) into the hole (D) ,then it can hold the position if the appliance is not going to be used. 3. Continue to push spring pin (C) and rotate the head unit, the element is lowered into the pan and the head unit is close to the operating position. 4. When the spring pin is put into the hole (E), the safety switch (F) will work and the appliance will work. The fryer can now be filled with the appropriate cooking oil. Connect the Fryer to the correct power supply and it is ready to operate. Telephone Helpline: 1300225960 Operation 1. Please ensure Oil level is between Min and Max lines. 2. Turn on the power switch. Then turn the thermostat dial to the required temperature setting. 3. Allow time for the oil temperature to reach the required setting. While the oil is heating, the green light will be on. When the oil has reached the required temperature, the green light will switch off. 4. As the oil temperature fluctuates, the thermostat will operate to maintain the set temperature, the indicator light will be lit when the Fryer is heating the oil. 5. A temperature setting of between 170°C and 180°C will be sufficient for most cooking. However this may vary for particular food types or according to individual requirements. Using the timer The digital timer with audible alarm can be set from 1 second to 15 minutes. The timer provides an audible alarm only; after the set time expires unit will continue to operate at set temperature. · START/STOP: Press START/STOP to start timer, press again to stop. The timer will provide an audible alarm after the set time. The alarm will beep 10 times and the display will continue to flash until timer is reset (press the START/STOP button). · UP: Press UP to add extra time. · DOWN: Press DOWN to reduce time. · PROGRAM: There are a total of 6 programmable timer settings. The default factory program settings are given below. Program Factory preset time 1 2 3 4 5 6 00:30 01:00 01:30 02:00 02:30 03:00 · To change the length of a program select the program you want to change by scrolling using the PROGRAM button. · Adjust the program time by using the UP and DOWN buttons. Press START/STOP to commence the count-down. The new program time will be automatically stored. · If the unit is left without power for more than 24hrs the timer settings will revert to the factory defaults. 4 '$"UP'$"@"@W@JOEC Telephone Helpline: 1300225960 AU Cleaning, Care & Maintenance The Fryer should be cleaned after each day's operation; however it may require cleaning more often, depending on the volume of frying carried out. 1. Switch off the power and disconnect from the power supply by removing the plug from the socket. 2. The Fryer must be left until the oil has cooled to room temperature before cleaning. 3. Empty oil by opening the drain tap at the front of the unit. Note: If the oil is to be reused, it should be filtered. 4. Once the oil has been emptied from the fryer, the head unit can be tilted back enabling the pan to be cleaned using warm soapy water. Warm soapy water is recommended for cleaning. Cleaning agents after prolonged use can cause damage to stainless steel. The main body can also be cleaned with warm soapy water. Remove the head unit and element before cleaning takes place. The head unit cannot be immersed in water, but can be wiped down with a damp cloth. After cleaning as above, please use a dry cloth to clean the appliance to ensure there is no water on the heating element and in the water oil pan. Troubleshooting Fault Probable Cause Appliance not working Unit not switched on Solution Check the unit is plugged in correctly and switched on Lead is damaged Call Apuro agent or qualified Technician Appliance does not reach set temperature Power supply Check power supply Faulty thermostat Call Apuro agent or qualified technician Faulty element Call Apuro agent or qualified technician Build-up of fat on the element Clean the appliance Appliance heats up but Indicator light has expired indicator light not ON Power indicator light Faulty element comes on but appliance does not heat up Faulty thermostat Thermostat set incorrectly Call Apuro agent or qualified technician Call Apuro agent or qualified technician Call Apuro agent or qualified technician Check thermostat Appliance slow to heat up No power Faulty element Call Apuro agent or qualified technician Build-up of fat on the element Clean the appliance Thermal cut-out activated Press re-set switch on rear of unit Technical Specifications Model FC374-A FC375-A FC376-A Voltage 220-240V~, 50Hz Power 2900W 2 x 2900W 6000W Capacity (Litres) 8L 2 x 8L 8L FC377-A 2 x 6000W 2 x 8L Max batch load (kg) 1 2 x 1 1 2 x 1 Dimensions H x W x D mm 440 x 280 x 510 440 x 560 x 510 440 x 280 x 510 440 x 560 x 510 Weight 9.5kg 17.0kg 10.4kg 18.8kg 5 '$"UP'$"@"@W@JOEC AU Telephone Helpline: 1300225960 Electrical Wiring: FC374-A/FC375-A The plug is to be connected to a suitable mains socket. This appliance is wired as follows: · Live wire (coloured brown) to terminal marked L · Neutral wire (coloured blue) to terminal marked N · Earth wire (coloured green/yellow) to terminal marked E This appliance must be earthed. If in doubt consult a qualified electrician. Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible. Electrical Wiring: FC376-A/FC377-A FC376-A and FC377-A are supplied unplugged and require hardwiring to a suitable electrical power supply capable of supporting 6KW at 220-240V/50hz. For FC376-A: This appliance is wired as follows: · Live wire (coloured brown) to terminal marked L · Neutral wire (coloured blue) to terminal marked N · Earth wire (coloured green/yellow) to terminal marked E This appliance must be earthed. If in doubt consult a qualified electrician. Electrical isolation points must be kept clear of any obstructions. In the event of any emergency disconnection being required they must be readily accessible. Connection to a suitable power supply should only be carried out by a qualified and competent electrical engineer. For FC377-A: 6 '$"UP'$"@"@W@JOEC Telephone Helpline: 1300225960 AU Compliance The product must not be disposed of as household waste. To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area. Apuro parts have undergone strict product testing in order to comply with regulatory standards and specifications set by international, independent, and federal authorities. Apuro products have been approved to carry the following symbol: All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written permission of Apuro. Every effort is made to ensure all details are correct at the time of going to press, however, Apuro reserve the right to change specifications without notice. '$"UP'$"@"@W@JOEC 7 DocuSign Envelope ID: AD52F341-7934-46D3-96D3-85DACAA38FF8 DECLARATION OF CONFORMITY · Conformiteitsverklaring · Déclaration de conformité · Konformitätserklärung · Dichiarazione di conformità · · Declaración de conformidad · Declaração de conformidade Equipment Type · Uitrustingstype · Type d'équipement · Gerätetyp Model · Modèle · Modell · Modello · Tipo di apparecchiatura · Tipo de equipo · Tipo de equipamento · Modelo · Malli Single Fryer 1 x 8Ltr 2.9kW with Timer FC374-A Double Fryer - 2 x 8Ltr 2.9kW with Timer FC375-A Single Fryer 1 x 8Ltr 6kW with Timer FC376-A Double Fryer - 2 x 8Ltr 6kW with Timer FC377-A Application of Territory Legislation & Electrical safety Council Directives(s) AS/NZS 60335.1:2011 +A1:2012 +A2:2014 +A3:2015 +A4:2017 Toepassing van Europese Richtlijn(en) · IEC 60335-2-37:2002 +A1:2008 +A2:2011 Application de la/des directive(s) du EN 62233:2008 Conseil · Anwendbare EU-Richtlinie(n) · Applicazione delle Direttive Electro-Magnetic Compatibility · Aplicación de la(s) directiva(s) del EN 55014-1:2017 consejo · Aplicação de directiva(s) do EN 55014-2:2015 Conselho EN 61000-3-2:2014 EN 61000-3-3:2013 Producer Name · Naam fabrikant · Nom du producteur · Name des Herstellers · Nome del produttore · Nombre del fabricante · Nome do fabricante Apuro I, the undersigned, hereby declare that the equipment specified above conforms to the above Territory Legislation, Directive(s) and Standard(s). Ik, de ondergetekende, verklaar hierbij dat de hierboven gespecificeerde uitrusting goedgekeurd is volgens de bovenstaande Richtlijn(en) en Standaard(en). Je soussigné, confirme la conformité de l'équipement cité dans la présente à la / aux Directive(s) et Norme(s) ci-dessus Ich, der/die Unterzeichnende, erkläre hiermit, dass das oben angegebene Gerät der/den oben angeführten Richtlinie(n) und Norm(en) entspricht. Il sottoscritto dichiara che l'apparecchiatura di sopra specificata è conforme alle Direttive e agli Standard sopra riportati. El abajo firmante declara por la presente que el equipo arriba especificado está en conformidad con la(s) directiva(s) y estándar(es) arriba mencionadas. Eu, o abaixo-assinado, declaro que o equipamento anteriormente especificado está em conformidade com a(s) anterior(es) Directiva(s) e Norma(s) Date · Data · Date · Datum · Data · Fecha · Data Signature · Handtekening · Signature · Unterschrift Firma · Firma · Assinatura 21st May 2021 Full Name · Volledige naam · Nom et prénom · Vollständiger Name · Nome completo · Nombre completo · Nome por extenso Ashley Hooper Josie Holt Position · Functie · Fonction · Position Technical & Quality Manager · Qualifica · Posición · Função Commercial Manager/ Responsible Supplier Producer Address · Adres fabrikant · Adresse du producteur · Anschrift des Herstellers · Indirizzo del produttore · Dirección del fabricante · Morada do fabricante Fourth Way, Avonmouth, Bristol, BS11 8TB United Kingdom 15 Bagdally Road, Campbelltown NSW 2560 '$"UP'$"@"@W@JOEC '$"UP'$"@"@W@JOEC '$"UP'$"@"@W@JOEC '$"UP'$"@"@W@JOEC '$"UP'$"@"@W@JOEC FC374-A to FC377-A_A5_v2_20210715Adobe PDF Library 15.0 Adobe InDesign 16.1 (Macintosh)