Instructions for NOTHING BUT LEDS models including: 1550392, LED Running Man Safety Exit Sign, Man Safety Exit Sign, LED Running Exit Sign, Exit Sign, Sign
LED Running Man Safety Exit Sign | 3.5W | 6000-7000K | Green | 120-347 – Nothing But LEDs
RUNNING MAN EXIT SIGN LED EMERGENCY LIGHTS UL R D Product Features · SKU # 1550392 · Output power: 3.5W · CCT: 6000K-7000K · Injection-molded thermoplastic ABS housing · Charging Time: 24H · Discharging Time: 90 MIN · Input Volt: 120/347V/60Hz · Battery: 3.6V 600mAh Ni-Cd Battery · IP Rating: IP20 · LED: 14 LEDS · Certifications: UL Listed · Warranty: (5 years warranty for the electrical parts and housing; 3 years warranty for battery)" 1 LED EMERGENCY LIGHTS RUNNING MAN EXIT SIGN SKU Number 1550392 Specificaons Parameter General Performance Descripon Model Mode of operation Supply Voltage Power Consumption Output Voltage Output Power Colour Temperature Battery Max Charge Current (mA) Max Discharge Current (mA) Charging Time Discharge Time LED Net Weight Gross Weight IP Rating Safety Classification Certification Picture Warranty Value JRMEEW Maintained 120/347V/60Hz 4.5W 4.5VDC 3.5W 6000K -7000K 3.6V 600mAh Ni-Cd Battery AC:85mA/DC:95mA 185mA 24H 90Min 14 LEDS 2.58LBS 2.64LBS IP20 UL Listed Five years warranty for the electrical parts and housing; Three years warranty for baery. 2 LED EMERGENCY LIGHTS 9.05" RUNNING MAN EXIT SIGN Dimensions 13.58 " 1.97 " 3 LED EMERGENCY LIGHTS RUNNING MAN EXIT SIGN Installation LED Pictogram Sign WARNING: Risk of Shock. Disconnect Power before Installation. IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. All servicing should be performed by qualified service personnel. 2. Disconnect power at fuse or circuit breaker before installing or servicing. 3. All electrical connections must be in accordance with local codes, ordinances and the National Electric code. 4. Do not use outdoors. 5. Do not let power supply cords touch hot surfaces. 6. Do not mount near gas or electric heaters. 7. Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by unauthorized personnel. 8. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. 9. Do not use this equipment for other than intended use. 10.Use caution when handling batteries. Battery acid can cause burns to the skin and eyes. If acid is spilled on the skin or eyes, flush acid with fresh water and contact a physician immediately. Avoid possible shorting. 11. Allow battery to charge for 24 hours before first use. SAVE THESE INSTRUCTIONS Installation Instructions 1. Turn off AC power. 2. Using a flat head screwdriver, insert the blade into the two slots and pry off the front cover (see figure 4). 3. Follow the proper mounting procedure below. Wall mount a. Remove the back plate from the packaging. b. Knock out the proper hole pattern on the back plate, including the center hole, to mount to a standard junction box by supporting the area around the knock outs with two blocks of wood. c. Remove the rear cover and diffuser. d. Install the back plate on to the unit. e. Feed the AC supply leads out through the center hole and make the proper connections (See step 4 and Fig.6). Ceiling or End Mount a. Attach crossbar to junction box, set the longer blade of the crossbar to touch the junction box. 4 LED EMERGENCY LIGHTS RUNNING MAN EXIT SIGN Installation b. Remove the mounting hole cover from the top or side d. Feed the unit wires the through canopy hole and make the proper connections (See step 4 and Fig.6). a. For 120VAC, connect the black wire (120VAC) and white wire (neutral) to the building utility. b. For 347VAC, connect the red wire (347VAC) and white wire (neutral) to the building utility. c. Feed wires back into the junction box. Risk of electrical shock. Cap unused wires. CAUTION! In all cases, use suitable wire nuts rated for the applicable voltage to connect to wires. 5. For universal AC/DC models: connect wires for external a. Wire the Yellow lead to the positive(+) b. Wire the Purple to the Negative(-) IMPORTANT! Electrical connections for AC and wires must be isolated from each DC other. PACKAGE Carton (Inch) 14.37x9.76x6.14 5 Qty / Carton 2PC Net Weight / Carton 5.07LBS Gross Weight / Carton 6.17LBS LED EMERGENCY LIGHTS RUNNING MAN EXIT SIGN Application Picture Warranty Five years warranty for the electrical parts and housing; Three years warranty for baery 6Adobe PDF library 16.03 Adobe Illustrator(R) 24.0