Monster Indoor Outdoor Atmos Soundbar SBA36G
User Manual
Model: MNSBA36G
Thank you for purchasing the MNSBA36G Soundbar. Please read this user manual carefully and keep for future reference.
Important Safety Instructions
Warning:
[Warning Symbol] CAUTION! RISK OF ELECTRIC SHOCK DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK)
Caution: To reduce the risk of electric shock, do not dismantle the product and do not expose the apparatus to rain or moisture. No user-serviceable parts inside. Refer servicing to qualified personnel only.
[Lightning Flash Symbol] The lightning flash within an equilateral triangle is intended to alert you to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute an electric shock to a person or persons.
Important! [Important Symbol] This symbol alerts you to read and observe important warnings and instructions on the unit or in this manual.
Notice: This appliance is not intended for use by persons (including children) with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
- To prevent possible hearing damage, do not listen at high volume levels for long time periods or a sudden high volume level. [Hearing Protection Symbol]
- Never use the device unsupervised! Switch off the device whenever you are not using it, even if not using it only for a short while.
- The appliance is not intended to be operated by means of an external timer or separate remote control system.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- Before operating this system, check the voltage of this system to see if it is identical to the voltage of your local power supply.
- The unit should not be impeded by covering the ventilation opening with items such as newspaper, table-cloths, curtains etc. Make sure that there are at least 20 cm of space above and at least 5 cm of space on each side of the unit.
- The apparatus must not be exposed to dripping or splashing liquid, no objects filled with liquids such as vases, should be placed on the apparatus.
- To prevent fire or shock hazard, do not expose this equipment to direct heat, rain, moisture or dust.
- Do not position this unit near any water sources e.g. taps, bathtubs, washing machines or swimming pools. Ensure that you place the unit on a dry, stable surface.
- Do not place this unit close to a strong magnetic field.
- Do not place the unit on an amplifier or receiver.
- Do not place this unit in a damp area as the moisture will affect the life of electric components.
- Do not attempt to clean the unit with chemical solvents as this might damage the finish. Wipe with a clean, dry or slightly damp cloth.
- When removing the power plug from the wall outlet, always pull directly on the plug, never pull on the cord.
- Depending on the electromagnetic waves used by a television broadcast, if a TV is turned on near this unit while it is also on, lines might appear on the LED TV. Neither this unit nor the TV is malfunctioning. If you see such lines, keep this unit well away from the TV set.
- The mains plug is used to disconnect the device, the disconnected device should remain readily operable.
Important Safety Instructions (Summary):
- Read and keep these instructions. Follow all instructions and heed all warnings.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with manufacturer's instructions.
- Do not install near heat sources like radiators, heaters, stoves, or other apparatus producing heat.
- Protect the power cord from being walked on or pinched, especially at plugs and points where it exits the apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, for example, when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. The AC plug is used to disconnect the device; the disconnected device should remain readily operable. To disconnect the apparatus from AC power completely, the AC plug must be removed from the AC outlet completely.
Preparation for Use
Unpacking and Set Up
- Remove the Sound bar from the carton and remove all packing material. Save the packing material for potential servicing or transportation needs. The original carton and packing material is the safest way to protect your Sound bar during transit.
- Remove any descriptive labels or stickers from the front or top of the cabinet. Do not remove labels or stickers from the back or bottom of the cabinet.
- Place your Sound bar on a level surface such as a table, desk, or shelf, conveniently located near an AC outlet, out of direct sunlight, and away from sources of excess heat, dirt, dust, moisture, humidity, or vibration.
- Unwind the Line cord connecting the AC adapter and extend it to its full length.
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from moving during operation. These 'feet' are made from non-migrating rubber material formulated to avoid leaving marks or stains on furniture. However, certain oil-based furniture polishes, wood preservatives, or cleaning sprays may soften the rubber 'feet', leaving marks or residue. To prevent furniture damage, it is strongly recommended to purchase small self-adhesive felt pads and apply them to the bottom of the rubber 'feet' before placing the unit.
Important Notes
- The safety and operating instruction manual should be retained for future reference.
- The apparatus should not be exposed to dripping, splashing, or placed in a humid atmosphere such as a bathroom.
- Do not install the product in the following areas:
- Places exposed to direct sunlight or close to radiators.
- On top of other stereo equipment that radiate too much heat, blocking ventilation, or in a dusty area.
- Areas with constant vibration.
- Humid or moist places.
- Near candles or other flames.
- Operate the product only as instructed in this manual.
- Before turning on the power for the first time, ensure the sound bar is plugged into a power outlet.
- For safety reasons, do not remove any covers or attempt to gain access to the inside of the product. Refer any servicing to qualified personnel.
- Do not attempt to remove any screws, or open the casing of the unit; there are no user-serviceable parts inside. Refer all servicing to qualified service personnel.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Note: The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user's authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirement. To maintain compliance with FCC's RF exposure guidelines, the distance must be at least 20 cm between the radiator and your body, and fully supported by the operating and installation configurations of the transmitter and its antenna(s).
Waterproof IPX4
The Sound bar provides robust durability by IPX4, allowing it to be used in outdoor environments (When installed and used as per the instructions in this User Manual). The remote control of this product also provides durability by IPX4.
Despite the IPX4 ratings, your sound bar and remote control are not impervious to water damage in any situation. To help prevent damage to your products, avoid subjecting them to:
- Water projected by a source greater than 6.3 mm against the enclosure from any direction or submersion in water.
- Water projected at greater than 30 kPs (4.4 psi) with a water volume greater than 12.5 litres/minute for more than 3 minutes and extreme weather conditions.
Product Diagram
Diagram Description: The product diagram shows the soundbar from the front, rear, and top. The front view displays the LED display and speaker grilles. The rear view details various ports labeled 1 through 6. The top view illustrates the control buttons and ports labeled 1 through 10.
- 1. LED DISPLAY
- 2. DC IN
- 3. OPTICAL
- 4. AUX
- 5. USB (ONLY UPDATE)
- 6. eARC
- 7. VOL-
- 8. Power/Standby ⏻
- 9. INPUT
- 10. VOL+
Remote Control
Diagram Description: The remote control features numerous buttons for operating the soundbar. Key buttons include Power, Pair, Light Mode, Mode, EQ, Bass, Treble, Input, Play/Pause, and Volume controls.
- 1. Power Button ⏻: Press to turn the unit on and off.
- 2. PAIR Button: Press and hold for more than 2 seconds to connect or disconnect to a pairing device.
- 3. LIGHT Mode Button: Cycles through light modes L1-L10. Long press for 2 seconds to enter monochromatic modes L11-L18.
- 4. MODE Button: Short press to switch modes (e.g., INDOOR/OUTDOOR). Default is INDOOR.
- 5. EQ Button: Short press to switch EQ modes (e.g., MUSIC, MOVIE, NEWS). Default is Music mode.
- 6. BASS+ Button: Increases bass level from -5 to +5. Default is 0.
- 7. Play/Pause Button: Short press to pause current music playback (under BT mode). Short press again to resume music playback.
- 8. PREV Button: Short press to skip to the previous track (under BT mode).
- 9. BASS- Button: Decreases bass level from -5 to +5. Default is 0.
- 10. INPUT Button: Short press to switch between input sources: BT/AUX/HDMI eARC/Optical.
- 11. Mute Button: Mutes the music; the display will flash.
- 12. Brightness Button: Adjusts brightness level (100%-75%-50%-25%, OFF).
- 13. GAME Button: When pressed, the soundbar display shows "GAMING". Default is Dance mode L9. The soundbar remembers the last set light mode.
- 14. VOL+ Button: Increases volume level from 0-32. 0 is Mute. Default is 10.
- 15. TREB+ Button: Increases treble level from -5 to +5. Default is 0.
- 16. NEXT Button: Short press to skip to the next track (under BT mode).
- 17. TREB- Button: Decreases treble level from -5 to +5. Default is 0.
- 18. VOL- Button: Decreases volume level from 0-32. 0 is Mute. Default is 10.
Notes:
- Long press the EQ button for 3 seconds to query and display the software version.
- Long press the Reset key for 5 seconds to restore factory default settings. This includes: Volume at 10, treble and bass at 0, default mode is Bluetooth, EQ is Music, MODE is Indoor, and RGB light is default to mode 2 Breath.
- USB is for update purposes only; no MP3 playback function is supported.
- The display and RGB light will turn off with no operation for 20 seconds. In GAME mode, only the display turns off, while the RGB light remains on. The display and RGB light will wake up again by pressing any button on the bar or remote control.
- The first time the soundbar is turned on, it defaults to Bluetooth mode. On subsequent power-ups, it remembers the last set mode from the remote control or soundbar button.
- The default volume is 10. When using an iPhone, volume synchronization occurs simultaneously.
Positioning the Sound Bar
Place on a flat Surface
Diagram Description: Two diagrams illustrate correct and incorrect placement on a flat surface. The correct placement shows the soundbar centered in front of a TV with adequate space behind it for airflow. The incorrect placement shows the soundbar too close to the wall or inside a cabinet.
Place the sound bar horizontally on a flat surface such as a TV unit or shelves and align it centrally with the TV screen. Allow some space between the speaker and the wall. Do not place inside a cabinet or an enclosed shelf. Follow this guidance for best sound output and good airflow around the sound bar.
Mount on the wall
WARNING: If you do not feel confident to correctly and securely wall-mount the sound bar, seek the assistance of an experienced person or professional.
Install the speaker on a vertical, firm, reinforced area of the wall. For plaster walls, it is recommended to screw into wall studs for greater security. For optimum performance, allow at least 25mm (1 inch) distance between the sound bar and the TV.
Diagram Description: Diagrams show the soundbar mounted on a wall, indicating the required 25mm (1 inch) clearance from the wall and the TV.
Follow below steps to mount the soundbar on the wall
Diagram Description: Four diagrams illustrate the wall mounting process: 1. Soundbar with wall bracket. 2. Wall with pre-drilled holes and anchors. 3. Wall bracket with EVA pads attached. 4. Soundbar being hung onto the wall bracket.
- Make 2 holes on the wall with the same distance as the wall bracket on the soundbar.
- Put the plastic anchors onto the wall and secure the screws to the plastic clip. Do not tighten the screws all the way; leave some space.
- Attach the 2 EVA pads onto the wall mount bracket. This will ensure enough room (minimum 15mm) between the wall and the soundbar outlet.
- Once the screws are securely fastened, hang the sound bar by inserting the screws onto the wall mount bracket.
OPERATE INSTRUCTIONS
Setting the Soundbar
- Plug in the power cord, and the display will light up (Standby mode).
- Switch on the sound bar by pressing the "POWER" button on the sound bar or on the remote controller. After switching on, the default input mode will appear on the display.
- Input modes can be changed by pressing the "INPUT" button on the sound bar or on the remote controller.
- Below are the input mode names appearing in the sound bar display:
- Bluetooth Pairing mode
- AUX mode
- Optical mode
- TV HDMI ARC mode
- TV HDMI eARC mode
HDMI IN (eARC) Support: The port of HDMI IN (eARC) supports Video & Audio. Maximum supported audio content includes Dolby Atmos, Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Surround. HDMI version is 2.1.
The screen will be turned off for around 20 seconds without any operation. When pressing the power buttons on the soundbar or remote control, or using the phone's volume increase or decrease, the display will wake up again.
Powering On/Off
- Plug the power cord of the sound bar into a wall outlet; it will automatically enter standby mode.
- Short-press the "POWER" button on the sound bar or remote controller to turn on the sound bar.
- To turn off, press and hold the "POWER" button for 2 seconds, then unplug from the wall outlet.
Diagram Description: A diagram shows the power cord being plugged into the soundbar and then into a wall outlet.
Light Modes
Diagram Description: Visual representations of 18 different light modes (L1-L18) are shown, each with a corresponding icon (X1-X18) and a brief description of the effect and its associated APP name.
- MODE L1: Constant lighting (Red, Green, Blue, White, Yellow, Purple, Pink, Orange). 7 colors auto-loop (2 secs per color). APP named SPIN.
- MODE L2: Breathing light mode (Red, Green, Blue, White, Yellow, Purple, Pink, Orange). Colors breathing mode auto-loop. APP named Breath.
- MODE L3: Colorful running mode (Red/Green/Blue/White/Yellow/Purple/Pink/Orange). Colorful running mode auto-loop. APP named SPWIRL.
- MODE L4: Dual-colored wave mode (Red/Green). 2 colors in wave state scrolling from right to left, auto-loop. APP named Wave.
- MODE L5: Ripple wave mode (Red/Green/Blue/White/Yellow/Purple/Pink/Orange). 7 colors from the center to the two sides of the ripples, auto-loop. APP named Mood.
- MODE L6: Colorful flow mode (Red/Green/Blue/White/Yellow/Purple/Pink/Orange). 7 colors scrolling from right to left, auto-loop. APP named Rainbow.
- MODE L7: Colorful ripple mode (Red/Green/Blue/White/Yellow/Purple/Pink/Orange). 7 colors in a monochrome state from the center to the two sides of the ripples, auto-loop. APP named Spark.
- MODE L8: Colorful flow wave mode (Red/Green/Blue/White/Yellow/Purple/Pink/Orange). 7 colors in a monochromatic coverage rolling around, auto-loop. APP named Flash.
- MODE L9: Spectrum light effect, middle fluctuation mode (Red/Green/Blue/White/Yellow/Purple/Pink/Orange). 7 colors from the middle to the left and right ends of the spectrum fluctuate automatically, cycle play. APP named Dance.
- MODE L10: Spectrum light effect, fluctuation at both ends mode (Red/Green/Blue/White/Yellow/Purple/Pink/Orange). 7 colors from the left and right ends to the middle with spectrum fluctuation, automatically cycle play. APP named Static.
- MODE L11: Monochrome red steady on. APP named Red.
- MODE L12: Monochrome green steady on. APP named Green.
- MODE L13: Monochrome blue steady on. APP named Blue.
- MODE L14: Monochrome purple steady on. APP named Purple.
- MODE L15: Monochrome amber steady on. APP named Amber.
- MODE L16: Monochrome light blue steady on. APP named Light Blue.
- MODE L17: Monochrome pink steady on. APP named Light Pink.
- MODE L18: Monochrome white steady on. APP named White.
Note: Long press the "LIGHT" mode button for 2 seconds on the remote control to quickly enter monochrome mode and select L11, L12... L18.
Playing Audio via BT Connection
- Turn on the sound bar and then short-press the "INPUT" button on the sound bar or remote controller to switch it to BT mode. The LED display on the sound bar will flicker in Bluetooth pairing mode.
- Activate the pairing function on your phone or other compatible device and select "MONSTER SBA36G" via BT connection.
- When successfully paired, you will hear a tone, and the LED display will stop flickering. Then music selected on your device can be played on the sound bar.
- The remote controller includes BT mode playback controls.
Notes:
- If your pairing device is switched off or manually disconnected, the sound bar will automatically enter pairing mode.
- If the connected device is switched off or manually disconnected, the soundbar will automatically enter pairing mode.
- Successfully connected devices will be re-established once you re-enter wireless connection range (10 meters).
- To connect to other devices, repeat the above pairing steps.
Diagram Description: A diagram illustrates a Bluetooth device (like a laptop or smartphone) connecting wirelessly to the soundbar, depicted with sound waves.
Audio input (Aux) Connection
- First, connect the soundbar to your PC, laptop, smartphone, TV, or other audio devices using an AUX cable provided. Ensure that these devices have both AUX IN and AUX OUT terminals.
- Then, press the INPUT button on the remote control or soundbar to switch the soundbar to Aux mode. Once connected in Aux mode, the screen will display "AUX". The music on your connected device will play. Playback can only be controlled on your connected device.
Note: For some computers, you may need to access the audio control panel to manually set the soundbar as the audio output device.
Optical Mode
Connection: Remove the cap of the optical cable (keep the cap for future use); check the direction of the plug. Connect the soundbar and TV with the optical cable.
Usage: Use this mode to play music from a TV with an optical digital output on the sound bar. In TV sound settings, select the soundbar optical connection (output for audio). When the optical cable is connected, the TV audio output should be set to Dolby or Auto mode.
The TV must have an optical digital output. Use the optical cable to make the connection as follows:
- Connect the optical cable to the optical digital output of your TV.
- Connect the optical cable to the optical digital input of your soundbar.
- Switch on the TV set and the soundbar. Set the connected TV to "Dolby or Auto mode".
- Start playing on the TV.
- Press the "INPUT" button on the remote control or on the soundbar to select OPT-OPTICAL mode.
- Use the volume buttons to adjust the volume to your requirements.
- You can also change the audio settings by using the relevant buttons on the remote control.
Notes:
- When connecting a device such as a TV/Set-top box/DVD/game console with an optical cable, set the audio output mode of the device to Dolby or Auto mode (digital optical output).
- Do not bend the optical cable, otherwise the cable inside will be damaged.
Diagram Description: Diagrams illustrate the optical cable connection between a TV's optical output and the soundbar's optical input.
HDMI IN eARC MODE
Connect to HDMI IN eARC Socket
Some 4K HDR TVs require the HDMI input or picture settings to be set for HDR content reception. For further setup details on HDR display, please refer to the instruction manual of your TV.
Option 1: e-ARC (enhanced Audio Return Channel)
Your Soundbar supports HDMI with enhanced Audio Return Channel (e-ARC). If your TV is HDMI e-ARC compliant, you can hear the TV audio through your Soundbar by using a single HDMI cable.
- Use a High Speed HDMI cable, connect HDMI IN eARC on the soundbar to the HDMI (e-ARC) connector on your TV.
- Then short-press the [INPUT Button] on the soundbar or the INPUT button on the remote controller to switch to HDMI IN eARC mode. After successfully connected, the LED display will show "eARC". (If the TV supports HDMI ARC, the LED display will show "ARC").
- Press the VOL +/- buttons to adjust the volume to your desired level.
- If you wish, you can change the audio settings by using the relevant buttons on the remote controller.
Notes:
- Your TV must support the HDMI-CEC and e-ARC function. HDMI-CEC and e-ARC must be enabled.
- The setting method for HDMI-CEC and e-ARC may differ depending on the TV. For details about e-ARC function, please refer to your TV owner's manual.
- Only HDMI 1.4 compatible cables can support the e-ARC function.
- The enhanced Audio Return Channel function enables an HDMI compatible TV to send the audio stream to the HDMI OUT of the unit.
TROUBLESHOOTING
| PROBLEM/TROUBLE | POSSIBLE CAUSE | SOLUTION |
|---|---|---|
| There is no sound output from sound bar. | Another input source is selected. | Select an appropriate input source. |
| The mute function is activated. | Cancel the mute function. | |
| The volume of sound bar or TV/other device is adjusted too low. | Increase the volume level on the sound bar or by remote control or on the TV. | |
| The power cable of the unit is not connected properly. | Make sure that the power cable of the unit is connected to an AC wall outlet securely. | |
| Input jacks on a playback device are connected incorrectly. | Connect the input jack on the sound bar and the output jack on the playback device correctly. | |
| Signals that the sound bar cannot playback when being input. | When sound bar and TV or other devices are connected by an audio cable through TV HDMI ARC or HDMI eARC port output, select the correct audio input and output. Make sure the digital audio output setting on the playback device is set to PCM format. Since the output format of our sound bar is PCM, if it is used, the decoding format of TV or other devices will be adjusted to PCM state. | |
| The sound is distorted or echoed. | TV volume is not muted. | If you play audio from TV through the sound bar, make sure that the TV is muted. |
| The automatic volume adjustment function is activated. To prevent excessive loudness, the unit automatically controls its volume within a certain level when the unit is turned on. | Turn up the volume as required. | |
| Noise is heard. | The sound bar is too close to another digital or high-frequency device. | Move those devices away from the sound bar. |
| The unit cannot be operated by using the remote control. | The unit is out of the operating range. | Use the remote control within the operating range. |
| The batteries are weak. | Replace with new batteries. | |
| The remote control sensor of the sound bar is exposed to direct sunlight or strong lighting. | Adjust the lighting angle or reposition the sound bar. Make sure our product cannot be used in sunlight. | |
| The TV cannot be operated by using the TV's remote control. | The unit is blocking the TV's remote control sensor. | Position the unit so that it does not obstruct the TV's remote control sensor. |
| A device cannot connect the sound bar or the unit cannot be connected to a Bluetooth device. | Bluetooth function of the device is not activated, not paired, or connected correctly. | Restart the sound bar and try pairing again. Ensure the Bluetooth function of the device is enabled; see the user manual of the device on how to enable the function and connect correctly. |
| Bluetooth is not selected as the input source. | Select Bluetooth as the input source. | |
| The unit is connected to a different Bluetooth device. | Un-pair the Bluetooth device that is currently connected and pair with the desired Bluetooth device. | |
| The unit is too far away from the Bluetooth device. | Move the Bluetooth device closer to this unit. | |
| A device emitting electromagnetic waves (such as a microwave oven, a wireless device, and so on) may be placed nearby. | Do not use this unit near devices that emit electromagnetic waves. | |
| The Bluetooth device that you are using may not support the protocol. | Use a Bluetooth device that supports the protocol. | |
| The connection profile registered in the Bluetooth device may not be functioning correctly for some reason. | Delete the connection profile in the Bluetooth device and then connect the Bluetooth device to this unit. | |
| Sound quality of audio play from a connected Bluetooth device is poor and connection is not stable. | The Bluetooth reception is poor. | Move the device closer to the sound bar, or remove any obstacle between the device and the sound bar. |
| The volume on the Bluetooth device may be too low. | Raise the volume on the Bluetooth device. | |
| No sound can be heard or sound breaks (Bluetooth mode) | Bluetooth is not selected as the input source. | Select the Bluetooth as the input source. |
| Playback on the device has not been performed. | Perform playback on the device. | |
| The sound output on the Bluetooth device may not be set to this unit. | Select this unit as the output device on the Bluetooth device. | |
| The connection to the Bluetooth device was cut off. | Connect with the Bluetooth device one more time. | |
| The unit may be too far away from the Bluetooth device. | Move the Bluetooth device near this unit. | |
| A device emitting electromagnetic waves (such as a microwave oven, a wireless device, and so on) may be placed nearby. | Do not use this unit near devices that emit electromagnetic waves. | |
| There is no sound from sound bar - HDMI IN(eARC) Mode | Incorrect HDMI cable is used causing no signal to be sent to soundbar. Incorrect input mode is selected. | 1. Make sure that the user connected the TV and sound bar by a 19-core HDMI cable. 2. The sound bar and TV are connected through TV HDMI eARC or HDMI ARC port output; make sure that the TV is HDMI eARC or HDMI ARC compliant. 3. Set the TV to HDMI ARC (CEC). Set the audio output mode of TV to PCM format. (Or refer to your TV user manual) |
| There is no sound from sound bar (OPTICAL Mode) | OPTICAL cable might be damaged and no signal is received by the soundbar due to a failed connection and incorrect operation mode selected. | 1. Replace the OPTICAL cable with a new one to connect. 2. Set your TV audio output to PCM format. (Please refer to your TV user manual) |
Dolby Atmos
Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, Dolby Vision, Dolby Atmos, and the double -D symbol are trademarks of Dolby Laboratories.
What is DOLBY ATMOS®?
Dolby Atmos® transports you from the ordinary into the extraordinary with breathtaking, moving audio that fills your room and flows above and around you. Dolby Atmos gives you an amazing experience you have never heard before by overhead sound, and all the richness, clarity, and power of Dolby sound.
Using DOLBY ATMOS®:
DOLBY ATMOS is only available in HDMI (e-ARC) mode. For the details of the connection, please refer to "HDMI Connection".
- To use Dolby Atmos® in HDMI (e-ARC) mode, your TV has to support Dolby Atmos®.
- Make sure that "No Encoding" is selected for bitstream in the digital audio output of the connected external device (e.g., Blu-ray DVD player, TV, etc.).
- While entering Dolby Atmos / Dolby Digital Plus format, the soundbar will show DOLBY ATMOS / DOLBY SURROUND.
Note:
- The full Dolby Atmos experience is only available when the Soundbar is connected to the source via a HDMI 2.0 cable.
- The Soundbar will still function when connected via other methods (such as a Digital Optical cable), but these are unable to support all of the Dolby features. Given this, our recommendation is to connect via HDMI to ensure full Dolby support.
Package Contents
Diagram Description: Images show all items included in the package: Soundbar, Remote Control, HDMI Cable, Wall Mounting Bracket Sets, Adapter, User Manual, Remote control battery, and QSG (Quick Start Guide).
- Soundbar X 1
- Remote Control X 1
- HDMI Cable 1m *1
- Wall Mounting Bracket Sets X 1
- Adapter 1.5m *1
- User Manual X 1
- Remote control battery
- QSG *1
Specifications
| Model | MNSBA36G |
| Technology | BT/AUX/eARC/OPT |
| Drivers | 55X85mm*4 |
| Power Output and harmonic distortion (FTC): | Front L + Front R:45W x 2, 3 Ohms, 45Hz-20KHz, > 7% T.H.D |
| Power Output (Reference): | Peak Power: 300W |
| Frequency Response | 45Hz-20KHz |
| Signal-to-Noise Ratio | ≥ 66dB |
| Impedance | 3Ω*4 |
| Power Input | DC 25V === 1.9A |
| Bluetooth Operating Range | Version: 5.3 Range: up to 10m |
| Dimensions | 75H*89D*900L mm |
