Business network solutions "engineered in Germany": LANCOM Systems GmbHCompliance proofs for products: LANCOM Systems GmbHConfluence Mobile - LANCOM Wissensdatenbanklancom-systems.com/SFP-module-MI
User Guide for LANCOM models including: 1800VAW-4G, 1800VAW-4G SD-WAN Gateway, SD-WAN Gateway, Gateway
LANCOM 1800VAW-4G: LANCOM Systems GmbH
Hardware Quick Reference Guide LANCOM 1800VAW-4G
File Info : application/pdf, 1 Pages, 661.27KB
DocumentDocumentHardware Quick Reference LANCOM 1800VAW-4G 4G antenna connectors Screw the supplied mobile radio antennas to the appropriate connectors. Power supply connection socket Use only the supplied power adapter. Reset button Short press > device restart Long press > device reset Micro SIM card slot Slide the SIM card into the SIM card slot using the marker to ensure that the card is the right way round. Ensure that the SIM card clicks into place on insertion. To remove the card from the device, press the card lightly into the device. Let go to release the SIM card from the slot. USB-C configuration interface A USB-C cable is required to configure the device (cable not supplied) RESET WAN interfaces (SFP / TP combo port) Insert a suitable LANCOM SFP module (e.g. 1000Base-SX or 1000Base-LX) into the SFP port. Choose a cable compatible with the SFP module and connect it as described in the SFP module's mounting instructions www.lancom-systems.com/SFP-module-MI. (SFP module and cable are not included) If desired, alternatively connect the WAN TP interface to a WAN modem using an Ethernet cable. Ethernet interfaces Use the cable with the kiwi-colored connectors to connect one of the interfaces ETH 1 to ETH 4 to your PC or a LAN switch. USB interface Connect a USB data medium or a USB printer to the USB interface. (cable not supplied) VDSL / ADSL interface Connect the VDSL interface and the TAE socket of the provider using the enclosed DSL cable for the IP-based connection. (For more information, please contact your Internet provider). Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide! i Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times. The power plug of the device must be freely accessible. Please note that support service for third-party accessories is excluded. Please observe the following when setting up the device When setting up on the table, use the enclosed self-adhesive rubber pads, if applicable. Do not rest any objects on top of the device and do not stack multiple devices. Keep all ventilation slots of the device clear of obstruction. Rack installation with the optional LANCOM CPE Rack Mount / CPE Rack Mount Plus (separately available) Mounting & connecting 4G Power Off Blue, permanently* 1x blue, inverse blinking* 2x blue, inverse blinking* 3x blue, inverse blinking* Device switched off Device ready for operation or device paired and LANCOM Management Cloud (LMC) accessible. Connection to LMC active, pairing OK, device not claimed Pairing error or LMC activation code/ PSK not present. LMC not reachable resp. communication error Online Off Blue, blinking Blue, invers blinking Blue, permanently WAN connection not active WAN connection in progress (e.g. PPP negotiation) Additional WAN connection in progress WAN connection active WAN Off Blue, permanently Blue, flickering No link available / interface switched off Link available, no data transmission Data transmission SFP Off Blue, permanently Blue, flickering No link available / interface switched off Link available, no data transmission Data transmission DSL Off Blue, blinking / fast blinking Blue, permanently Interface switched off DSL Handshake DSL Training DSL Sync LANCOM 1800VAW-4G ETH1 - ETH4 Off Blue, permanently Blue, blinking No link available or interface switched off Link available, no data transmission Data transmission 4G Off Blue, blinking Blue, permanently Blue, flickering Cellular interface switched off Registration on the mobile radio system in progress Logon to the mobile radio system successful Data transmission WLAN 1 / WLAN 2 Off Blue, blinking Blue, permanently No Wi-Fi network defined or Wi-Fi module disabled. No beacons are sent from the Wi-Fi module. DFS Scanning or other scan process At least one Wi-Fi network defined and Wi-Fi module activated. Beacons are sent from the Wi-Fi module. VPN Off Blue, blinking / inverse blinking Blue, permanently No VPN connection active VPN connection in progress / additional VPN connection in progress VPN connection active Hardware Power supply Environment Housing Fan 12 V DC, external power adapter For an overview of the power supplies compatible with your device, see www.lancom-systems.com/kb/power-supplies. Temperature range 0 40 °C; humidity 0 95 %; non-condensing Robust plastic housing, connectors on the back, prepared for wall mounting; dimensions 293 x 44 x 190 mm (W x H x D) 1 quiet fan Interfaces VDSL2 VDSL2 acc. to ITU G.993.2; profiles 8a, 8b, 8c, 8d, 12a, 12b, 17a, 30a, 35b VDSL Supervectoring acc. to ITU G.993.2 (Annex Q) VDSL2 vectoring acc. to ITU G.993.5 (G.Vector) Compatible with VDSL2 and with Deutsche Telekom`s U-R2 connection (1TR112) ADSL2+ over ISDN acc. to ITU G.992.5 Annex B/J with DPBO, ITU G.992.3 and ITU G.992.1 ADSL2+ over POTS acc. to ITU G.992.5 Annex A/M with DPBO, ITU G.992.3 and ITU.G.992.1 Supports only one virtual circuit in ATM (VPI-VCI pair) at a time WAN (Combo port) WAN SFP: Slot for small form-factor pluggable Gigabit Ethernet transceiver (mini-GBIC). SFP / TP Compatible with optional LANCOM SFP modules for fiber optic connections. Switched as WAN port at delivery, can be configured as LAN port. WAN TP: 10 / 100 / 1000 Base-TX, Autosensing Full duplex, Auto node hub ETH 4 individual 10 / 100 / 1000-Mbps Fast Ethernet ports; operate as switch ex-factory. Up to 3 ports can be switched as additional WAN ports. USB USB 2.0 Hi-Speed host port for connecting USB printers (USB print server), serial devices (COM-port servers), or USB data media (FAT file system) Wi-Fi Frequency bands: 2400-2483.5 MHz (ISM) and 5150-5725 MHz (country-specific restrictions possible) Radio channels 2.4 GHz: Up to 13 channels, max. 3 non-overlapping (2.4 GHz band) Radio channels 5 GHz: Up to 26 non-overlapping channels (available channels depending on country-specific regulation and associated with automatic, dynamic DFS channel selection) 4G 2 SMA connectors for the supplied dipole rod antennas, suitable LANCOM AirLancer antennas for 4G or other manufacturers. Please take into account the legal regulations of your country for the operation of antenna systems (especially antenna gain and transmission power). Configuration interface USB-C configuration interface WAN protocols Ethernet PPPoE, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without DHCP) Package content Cable Antennas Power adapter 1 DSL cable for an IP-based line, 4.25 m; 1 Ethernet cable, 3m 2 4G antennas for 4G / LTE External power adapter *) The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Management Cloud. This product contains separate open-source software components which are subject to their own licenses, in particular the General Public License (GPL). The license information for the device firmware (LCOS) is available on the device`s WEBconfig interface under "Extras > License information". If the respective license demands, the source files for the corresponding software components will be made available on a download server upon request. Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006. The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc LANCOM, LANCOM Systems, LCOS, LANcommunity and Hyper Integration are registered trademarks. All other names or descriptions used may be trademarks or registered trademarks of their owners. This document contains statements relating to future products and their attributes. LANCOM Systems reserves the right to change these without notice. No liability for technical errors and/or omissions. 0523 LED description & technical details