Maris Water Hub
Installation Manual
Safety Information
⚠ Warning! Before proceeding with installation, read the safety information in the User Manual.
ℹ Important! Read other chapters in the User Manual that are necessary for proper installation, operation, and maintenance.
The document is available in multiple languages including English (EN), German (DE), French (FR), Dutch (NL), Italian (IT), Spanish (ES), Danish (DA), Norwegian (NO), and Swedish (SV).
Product Overview
The Maris Water Hub is a 3-in-1 electronic boiling water system, providing filtered boiling water directly from the tap. It is designed for convenient and efficient use in kitchens.
Specifications
Dimensions
Tap Dimensions: Height: 388 mm, Reach: 243 mm. Spout rotation: 180°, Tilt: 50°. Maximum spout reach (R max): 222 mm.
Mounting Plate Dimensions: Diameter: 90 mm, Height: 80 mm, Cutout diameter: Ø61 mm.
Filter/Booster Unit Dimensions: Height: 295 mm, Diameter: Ø95 mm.
Boiler/Storage Tank Dimensions: Unit 1: Height 340 mm, Base 229x229 mm. Unit 2: Height 494 mm, Base 229x229 mm.
Minimum Hole Sizes for Installation
- DN 6: Ø 50 mm
- DN 8: Ø 60 mm
- DN 10: Ø 70 mm
- DN 13: Ø 90 mm
Countertop Preparation
Ensure a hole of Ø 35 mm is prepared in the countertop. Maintain a minimum clearance of 40 mm around the hole and a minimum of 30 mm clearance below the countertop.
Tools Required
The installation requires the following tools: Tape measure, drill, screwdriver, pliers, and a utility knife.
Component Part Numbers
Power Switch: 112.0561.116 EU, 112.0737.105 UK.
Cold Fill / Hot Fill Unit: 112.0728.340.
Installation Guide
Follow these steps carefully for installation. Always ensure the water supply is turned off before starting.
Step 1: Tap Mounting
Install the tap through the prepared Ø 35 mm hole in the countertop. Ensure the countertop thickness does not exceed 45 mm.
Step 2: Water Connections
Connect the water supply lines to the tap and the filter/booster unit. Fittings used are G3/8 and G1/2, with a nominal diameter of Ø20.8 �b1;0.3 mm. For UK installations, a 3/8" connection may be used, equivalent to 1/2".
Step 3: Filter and Booster Unit Installation
Install the filter and booster unit, ensuring it is positioned correctly and securely.
Step 4: Hose Routing
Route all hoses neatly and safely, ensuring no kinks or damage.
Step 5: Unit Placement
Position the filter and booster unit with a minimum clearance of 80 mm around it for ventilation and access.
Step 6: Hose Connections
Connect the hoses from the filter/booster unit to the tap, control unit, and boiler/storage tank as per the diagrams.
Step 7: Control Unit Installation
Mount the control unit in a suitable location.
Step 8: Control Unit Connections
Connect the hoses to the control unit and then connect the control unit to the tap. The system is designed to deliver water up to 100°C.
Step 9: Electrical Connection
Connect the power supply to the booster unit. Ensure the connection is secure and in a safe location.
Step 10: Tap Operation
To operate the tap, turn the handle to position 1, then to position 2. An initial fill of the system may take up to 1 minute.
Step 11: Flush Cycle
After installation, a 15-minute flush cycle is required to ensure the system is clean and ready for use.
Cold Fill (A) Configuration
This configuration (Part No. 112.0728.340) details the connection for cold water supply to the system, leading to the dispensing of boiling water.
Hot Fill (B) Configuration
This configuration (Part No. 112.0728.340) details the connection for hot water supply to the system, in addition to the boiling water function.
Maintenance
Cleaning the Tap
Regular cleaning of the tap is recommended to maintain its appearance and function. Use a soft sponge, a soft cloth, and a mild detergent. Avoid abrasive cleaning materials or pads that could scratch the surface.
The tap can be disassembled for thorough cleaning. Refer to the diagrams for disassembly guidance, noting fittings such as 25 mm and 2.5 mm.
Filter/Booster Unit Maintenance
Instructions for installing and removing the filter/booster unit are provided in the diagrams.
Tap Components
The tap assembly consists of the following main parts:
- Tap body
- Handle mechanism
- Control lever
- Mounting hardware
- Water inlet hoses
- Boiling water outlet hose
- Mounting bracket
Home
