Kinco步科
Instruction Manual for Kinco models including: GT070E, GT070E-4G, GT070E-WiFi, IoT Series, IoT Series Wifi Hmi Touch Screen, Wifi Hmi Touch Screen, Hmi Touch Screen, Touch Screen, Screen
File Info : application/pdf, 2 Pages, 1,017.07KB
DocumentDocumentGT070E/GT070E-4G /GT070E-WiFi
`DC24V' `GND'`FG'
3.
0755-26585555 0755-26616372 400-700-5281 http//www.kinco.cn Emailsales@kinco.cn 6
1.
1.1 GT070E/GT070E-4G/GT070E-WiFi
32~1220~50NEMA GT070E/GT070E-4G/GT070E-WiFi NEMA1
1.2 DC10VDC28V
GT070E/GT070E-4G/GT070E-WiFi
2.
2.1
2.2
HMI 0.5N.m
3.1
1 2 3
DC24V GND FG
3.2 COM0/COM2
1 Rx-(B)
2 RxD_PLC
3 TxD_PLC
4
Tx-
5
GND
6 Rx+(A)
7 RxD_PC
8 TxD_PC
9
Tx+
COM0/COM2 9 D COM0 RS232/485/422 COM2 RS232
PLC COM0 [RS-422] RS422 R-
RS422 TRS422 R+
RS422 T+
PLCCOM0 [RS-485]
RS485 B
PLC COM0 [RS-232]
PC/PLC COM2 [RS-232]
RS232 RxD RS232 TxD
RS485 A
RS232 RxD RS232 TxD
3.3 USB HOST USB U USB U /
3.4 USB SLAVE MicroUSB
USB PC / HMI
3.5 10M/100M RJ45 UTP HMI / HMI PLC PC
3.6 WiFi GT070E-WiFi WiFi
3.7 4G GT070E-4G 4G 4G IP
PLC 3.8
4.
http://www.kinco.cn
2.3
PLC1.ir
GT070E/GT070E-4G /GT070E-WiFi HMI
Installation Instruction
line to the 'FG' terminal.
3.External Interface
Kinco Electric (Shenzhen) Ltd.
AddBuilding 1, No. 6 Langshan 1st Rd, Hi-tech Park North, Nanshan, Shenzhen, China. Tel0755-26585555 Fax0755-26616372http//www.kinco.cn Emailsales@kinco.cn
1. Installation Note
1.1 Environmental Requirement Operating temperature: GT070E/GT070E-4G/GT070E-WiFi HMI can work stably in most industrial
environments that the temperature between 32°F to122°F (0~50°C). NEMA rating: This Series HMI frontpanel is NEMA 1 rated.
Please do not use in the following places:
Places direct in sunlight Surrounding temperature and humidity beyond
the specifications Places of temperature changes sharply and easily
cause condensation Places that exist corrosive gas and combustible
gas Places of much dust, dirt, salt and iron powder Places that will be splashed water, oil and drugs Places that bring direct vibration and shock to
Please take shielding
measures in the following
places:
Places
that
exist
electrostatic or other kinds
of noise
Places
of
strong
electromagnetic
Places that may be exposed
to rays
Places near the power
1.2 Power Requirement
Input voltage:DC10 VDC28V.
Particularly note that there must be enough distance between this product and converters or switch
mode power supply. Make sure that the input and output cables of that kind equipment are shield
cable and the shielding network is connected with the ground.
Make sure that the DC power and AC power is isolated.
Do not use common power with perceptual load or input circuit of the controller.
Note: An Internal fuse will prevent damage for over voltage condition, however it isn't guaranteed the internal electronic components are not damaged.
2.Installation Description
2.1Dimensional Drawing
2.2 Fixed Screw Installation Instructions
The product is put into the well mounted hole of the machine control box's panel, and the mounting screws are inserted into the fixing holes around the HMI shell from the back of the control box's panel. Recommended lock torque: 0.5N.m (to waterproof effect and avoid shell deformation)
2.3 Power Connection Before connecting the power, please make sure all local and national electrical standards are met.For power cables,please select cables with their dielectric strength values and current values in compliance with the safety specifications. First find the power terminal at the back of the product and loosen the screw according to counterclockwise, then insert the power cables and tighten the screw up. Connect positive DC line to the `DC24V' terminal, the DC ground to the `GND' terminal and the ground
PLC1.ir
3.1 POWER
Pin#
Signal
1
DC24V
2
GND
3
FG
3.2 COM0/COM2
Pin Signal
1 Rx-B
2 RxD_PLC
3 TxD_PLC
4
Tx-
5
GND
6 Rx+(A)
7 RxD_PC
8 TxD_PC
9
Tx+
Pin assignment of the 9-pin male, D-SUB, COM0/COM2.Note: RS232/485/422 communication functions are supported by COM0.COM2 supports RS232 communication function.
PLC COM0 [RS-422]
PLCCOM0 [RS-485]
PLC COM0 [RS-232]
PC/PLC COM2 [RS-232]
RS422 R-
RS485 B
RS232 RxD
RS232 TxD
RS422 T-
RS422 R+
Signal ground RS485 A
RS232 RxD
RS232 TxD
RS422 T+
3.3 USB HOST
Connection Connect with USB interface devices or U disks
Port Function
This interface can be connected with USB keyboard, mouse and printers, and the U disk can be used for user's configuration uploading/ downloading as well as data storage.
3.4 USB SLAVE
The interface type is MicroUSB
Connection Port
Function
USB Slave port can be connected with a PC The port is only used to download user configuration program to the HMI and to set HMI system parameters.
3.5 Ethernet
10M/100M adaptive Ethernet RJ45 port.
Connection With CAT5 UTP cable connected to the Ethernet device.
Port Function
The port can be used for upload/download of HMI configuration, setting of system parameters and online simulations of configurations. It can connect multiple HMIs via the Ethernet to form an HMI network. Furthermore, it can implement communications between HMI and PLC via the Ethernet, as well as communications with a PC via the Ethernet port.
3.6 WiFi function (only supported by GT070E-WiFi
Function: data transmission and download through wireless WiFi connection
3.7 4G function (only supported by GT070E-4G
Function: Connect via Internet 4G (the default external network routing priority is 4G) and then Ethernet; Ethernet PLC communication with IP is bound to carry out data transmission and download according to the selected network port communication.
3.8 suction cup antenna Customers can choose suction cup antenna according to product requirement
4.After-sales Service
For < Service Terms and Conditions for HMI >, please check:http://www.kinco.cn