Instruction Manual for CTA models including: PAD-LEDPARAF Premium Floor Stand with LED Light Add-On, PAD-LEDPARAF, Premium Floor Stand with LED Light Add-On, Floor Stand with LED Light Add-On, Stand with LED Light Add-On, LED Light Add-On, Light Add-On, Add-On
CTA Digital Premium Floor Stand with LED Light Add-On - iPad Air 11 inch M2 (2024) PAD-LEDPARAF: Stands & Cabinets - COLAMCO.com
Premium Floorstand with LED Light Add-On for 9-11" Tablets PAD-LEDPARAF INSTRUCTION - MANUAL CONTENTS: A x1 B x1 C x1 D x2 LED Bars E x1 F x1 G x1 H x1 I x1 M5 Allen Key K x1 J x1 M6 Allen Key L x4 M5 x 10 M x4 M6 N x1 INSTALLATION: 1. Assembling floorstand base: 2. Cable routing: A J M 2A. To route a charge cable through the stand, attach the weighted pendant to your charge cable, then pass through the cutout at the top of the stand. M6 x4 B 1A. Allign the holes on the sntad (A) with holes on the base (B) and turn in screws (M) with provided allen tool (J) until securely tightened. Shown above. 3. Attaching enclosure to VESA plate: I C A L x4 M5 x 10 3A. Align enclosure (C) VESA holes to VESA plate holes in stand (A) and from the front of enclosure turn in screws (L) into the threaded VESA holes with provided allen tool (I) until securely thigtened. Shown above. 2B. When the cable reaches the bottom of the stand, pull through the hole at the stand back and remove the weighted pendant as shown. 4. Inserting tablet into enclosure: **Tablet for illustration only, NOT INCLUDED K K C 4A. Find the appropiate size foam padding (K) for the tablet you wish to use. Make sure device is compatible for the enclosure. if having power/data cord attached to tablet, slide it through the back of the foam as shown and out the opening in the back. 718-963-9845 5. Optional - Placing blank sheet insert into enclosure: K K K **Tablet for illustration only, NOT INCLUDED C 5A. Lay-in correct masking insert from bundle (K) as needed the correct fitted look for your device. 5B. Close and lock enclosure afterwards and you`re set 6. Removing back covers: **Tablet for illustration only, NOT INCLUDED C 7. Setting up security: **Tablet for illustration only, NOT INCLUDED x1 N K C 6A. When installing device into enclosure (C), identify where the camera is. Then simply remove and pop out the cover prior to mounting or setting up tablet to properly expose camera. 7A. Once the tablet device is set up, close the front lid of the enclosure (C). 7B. Insert the key (N) in the keyhole on top of enclosure, and turn clockwise to lock the enclosure in place. 8. Setting Up LED Bar: 9. Attaching Wire Storage Component: D H 1A. Peel off the 3M adhesive sticker on the back of the LED light bar (D) as illustrated. Attach the LED bar onto the edge of the CTA floor stand with the wire end on the bottom side. Repeat same steps for the LED bar on the other side of the floor stand. 2A. Take the cable storage (H) and magnetically affix onto the backside of the floor stand as illustrated above. Be sure to have the openings at the bottom side when orienting storage component . 718-963-9845 10. Cable Routing and Cable Management: H A D 10A. Take the cables attached to the LED (A) and attach them to the bottom half power cable (B) via USB connection. 11. Cable Routing and Cable Management (Continued): 10B. Route all the cables into the cable storage component (E) as illustrated. H G 11A. Route the power cable out the bottom of the cable storage (H) 11B. Attach the power adapter (D) to the end of the cable as illustrated. Then plug into power source as needed. 718-963-9845Adobe PDF library 17.00