Manuals+

Weiser Electronic Deadbolts Programming Guide

This guide provides simplified programming instructions for various Weiser electronic deadbolts.

Troubleshooting Steps

In case of problems, always follow these steps:

  1. Factory reset
  2. Latch orientation
  3. User code programming
  4. Ask the customer for their guide and pencil

Note: During an initial installation, skip step 1.

Powerbolt 2 (GED1300)

Important Notes:

1. Factory Reset

A- Press and hold the PROG button for approximately 30 seconds. You will hear a long beep. Release the button.

B- Press PROG again and release. You will hear 3 long beeps.

2. Latch Orientation (Right Side)

A- Facing the door, on the exterior side, your Powerbolt is on the right.

B- Press PROG. You will hear 2 beeps.

C- Press the lock symbol [lock].

D- Press 56.

E- Press PROG.

2. Latch Orientation (Left Side)

A- Facing the door, on the exterior side, your Powerbolt is on the left.

B- Press PROG. You will hear 2 beeps.

C- Press the lock symbol [lock].

D- Press 12.

E- Press PROG.

3. Program User Code (4 digits)

A- Write your user code in your instruction manual (4 to 8 digits).

B- Press the PROG button. You will hear 2 beeps.

C- Press 12.

D- Press PROG.

D- Enter your user code.

E- Press PROG.

F- Test the code:

Powerbolt 2 (GED1460)

Important Notes:

1. Factory Reset

Set the latch to the locked position.

  1. With your pencil, press and hold the reset button.
  2. Remove the pencil upon hearing a beep. Wait approximately 10 seconds.

The master code will be 0-0-0-0 (factory code).

The user code will be 1-2-3-4 (factory code).

2. Program Latch Orientation

Set the latch to the unlocked position.

A- Enter code 0-0-0-0.

B- Press the lock symbol [lock].

C- Press 0.

D- Press the lock symbol [lock].

E- There will be 2 beeps for success, 3 red beeps for failure.

3. Change Master Code

This is your code to program user codes.

A- Write your new master code in the instruction manual.

B- Enter code 0-0-0-0.

C- Press the lock symbol [lock].

D- Enter 7.

E- Press the lock symbol [lock].

F- Enter your new code (4 to 10 digits).

G- Press the lock symbol [lock].

4. Create a User Code (up to 6)

A- Write your new user code in the instruction manual.

B- Enter your new master code.

C- Press the lock symbol [lock].

D- Enter 1.

E- Press the lock symbol [lock].

F- Enter your new code (4 to 10 digits).

G- Press the lock symbol [lock].

5. Delete Factory User Code

Very important

A- Enter your new master code.

B- Press the lock symbol [lock].

C- Enter 3.

D- Press the lock symbol [lock].

E- Enter 1-2-3-4.

F- Press the lock symbol [lock].

SmartCode 5 (GED1490)

Important Note:

Always keep the door open during operation and insert the key into the lock.

1. Factory Reset

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the program button until a beep is heard. The LED will flash red, for approximately 30-40 seconds.

C- Release the button at the moment of the beep.

D- Press the program button again and release.

E- Wait approximately 10-20 seconds, 1 beep and green light.

2. Program Latch Orientation

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the lock symbol [lock].

C- Release the button when the latch starts to move. You will hear a beep and see a green LED.

D- At this stage, the door cannot yet be locked using the lock symbol [lock].

3. Program User Code (8)

A- Write your user code in your instruction manual.

* The first 4 digits of each combination must be different.

B- Press the program button. You will hear 2 beeps.

C- Press 1. You will hear a short beep and the keypad will flash green.

D- Press the WEISER button.

E- Enter your user code.

F- Press the WEISER button.

G- You will hear a long beep and the keypad will flash green in case of success, red in case of failure.

4. Program a 2nd User Code

A- Write your user code in your instruction manual.

B- Press the program button twice.

C- Enter your code (4 to 8 digits).

D- Press the lock symbol [lock].

E- Test the code:

SmartCode 10 (GED2600, GED2700, GED1700)

Important Note 1:

Always keep the door open during operation and insert the key into the lock.

1. Factory Reset

A- Press the programming button for approximately 30 seconds using your Smart tool or a paperclip.

B- Release the button upon hearing a long beep.

C- Test a code; all codes are erased if the operation is successful.

Important Note 2:

This model does not require latch orientation.

2. Program User Code 30

A- Write your user code in your instruction manual, 4 to 8 digits.

* The first 4 digits of each combination must be different.

B- Press the program button. You will hear 2 beeps.

C- Press 1. You will hear a short beep and the keypad will flash green.

D- Press the WEISER button.

E- Enter your user code.

F- Press the WEISER button.

G- You will hear a long beep and the keypad will flash green in case of success, red in case of failure.

SmartCode 10 (GED1700)

Important Note:

Always keep the door open during operation and insert the key into the lock.

1. Factory Reset

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the program button until a beep is heard. The LED will flash red, for approximately 30-40 seconds.

C- Release the button at the moment of the beep.

D- Press the program button again and release.

E- The LED will turn green if the operation was successful. Wait approximately 15 seconds.

2. Program Latch Orientation

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the lock symbol [lock]. Release when the motor engages. You will hear a beep and see a green LED.

C- At this stage, the door cannot yet be locked using the lock symbol [lock].

3. Program User Code

A- Write your user code in the instruction manual.

B- Press the programming button.

C- Enter your user code.

D- Press the lock symbol [lock].

E- Test the code:

SmartCode 10 (GED2100)

Important Notes:

1. Factory Reset

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the program button until a beep is heard. The LED will flash red, for approximately 30-40 seconds.

C- Press the program button again and release.

D- The LED flashes from green to red multiple times.

E- After a few seconds, the latch orientation process will activate.

2. Program User Code (16)

A- Write your user code in your instruction manual.

B- Press the program button.

C- Press the hook symbol [hook].

D- Enter your new user code.

E- Press the lock symbol [lock].

F- The operation is successful if the hook symbol [hook] lights up with a beep.

H- Test your code:

Obsidian (GED2300)

Important Notes:

1. Factory Reset

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the program button until a beep is heard. The LED will flash red, for approximately 30-40 seconds.

C- Press the program button again and release.

D- The LED flashes from green to red multiple times.

E- After a few seconds, the latch orientation process will activate.

2. Program a User Code (16)

A- Write your user code in your instruction manual.

B- Press the program button.

C- Press the hook symbol [hook].

D- Enter your new user code.

E- Press the lock symbol [lock].

F- The operation is successful if the hook symbol [hook] lights up with a beep.

G- Test your code:

Premis (GED2200)

Important Notes:

  1. Always keep the door open during operation and insert the key into the lock.
  2. To activate the keypad, touch the screen with the back of your hand. Press the 2 digits that will light up.

1. Factory Reset

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the program button until a beep is heard. The LED will flash red.

C- Press the program button again and release.

D- The LED will flash green multiple times.

E- After a few seconds, the latch orientation process will activate.

2. Program a User Code

  1. Download the Weiser Premis application from the Apple App Store.
  2. Select My Home or create your own home. (Enter your name)
  3. Enter the room where your Premis is located.
  4. Select the detected lock, indicate yes if it beeps.
  5. Scan the 8-digit code on the back of the lock and give it a name.
  6. Enter your user code to unlock the lock on your phone.

Kevo Contemporain (GED1500)

Important Note:

Always keep the door open during operation and insert the key into the lock.

1. Factory Reset

A- Press button A for 10 seconds. You will hear a beep and the indicator lights will turn red.

2. Latch Orientation

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the programming button. Once the batteries are in place, remove your finger.

C- Press the programming button again when the indicator light flashes red and green.

3. Download the Kevo Application

A- On the Apple App Store, download the Kevo application.

B- Press Get started. (Create your account)

C- Allow Bluetooth usage and notification display.

D- Press + to program your lock.

E- Press 'Pair a device'.

F- Press 'Pair a Device', select the correct brand (Weiser, Kwikset, or Baldwin), select Contemporain.

G- Remove the back cover.

H- Press the programming button then lightly touch the lock with your phone.

4. Calibration of your Kevo

A- Press "continue".

B- Go outside with your key and your phone.

C- Put the phone in your pocket, handbag, or backpack.

D- Stand within arm's length of the door and touch your Kevo with your hand. It will calibrate the distance between the door and the phone.

E- Touch to open and close 10 times or until your phone vibrates and sends you a notification.

Aura (GED18500)

Important Notes:

  1. Always keep the door open during operation and insert the key into the lock.
  2. Secure Screen System
  3. To activate the keypad, touch the screen with the back of your hand. Press the 2 digits that will light up.

1. Factory Reset

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the program button until a beep is heard. The LED will flash red.

C- Press the program button again and release.

D- The LED will flash green multiple times.

E- After a few seconds, the latch orientation process will activate.

2. Pair your phone to your lock

  1. Download the Weiser application from the Apple App Store.
  2. Create your Weiser account.
  3. Top right corner, press + then press NEXT.
  4. Press button A for 3 seconds, release upon beep and press next.
  5. Your lock's identifier will appear, press the name.
  6. Upon beep, press YES. Your phone will ask you to accept pairing.

3. Create your user code

  1. Name your lock.
  2. Name the user.
  3. Enter your 4-8 digit code.
  4. Set the schedule for this code.
  5. Press SUBMIT.

4. Transfer a user code by email

  1. After creating a user code, press the keypad icon (bottom left corner).
  2. Press the code you wish to share.
  3. Press Share Access Code and follow your messaging app instructions.

Halo (GED25000)

Important Notes:

  1. Always keep the door open during operation and insert the key into the lock.

1. Factory Reset

A- Remove the battery pack.

B- Reinsert the battery pack while pressing the program button until a beep is heard. The LED will flash red.

C- Press the program button again and release.

D- The LED will flash green multiple times.

E- After a few seconds, the latch orientation process will activate.

2. Pair your phone to your lock

  1. Download the Weiser application from the Apple App Store.
  2. Create your Weiser account.
  3. Top right corner, press + then press NEXT.
  4. Press button A for 3 seconds, release upon beep and press next.
  5. Your lock's identifier will appear, press the name.
  6. Upon beep, press YES. Your phone will ask you to accept pairing.

3. Pair your lock to your home router

A- Proceed to update the application.

B- Enter your access protection code for your router.

4. Create your user code

  1. Name your lock.
  2. Name the user.
  3. Enter your 4-8 digit code.
  4. Set the schedule for this code.
  5. Press SUBMIT.

5. Transfer a user code by email

  1. After creating a user code, press the keypad icon (bottom left corner).
  2. Press the code you wish to share.
  3. Press Share Access Code and follow your messaging app instructions.

PDF preview unavailable. Download the PDF instead.

Guide depannage Weiser Electronique Microsoft PowerPoint 2016 Microsoft PowerPoint 2016

Related Documents

Preview Weiser Door Hardware Catalog and Ordering Guide
Explore the comprehensive Weiser product catalog featuring a wide range of door hardware, including handlesets, levers, knobs, deadbolts, and electronic locks. Discover Weiser's innovative SmartKey security and Microban antimicrobial technology. This guide provides detailed product specifications, ordering information, and terms and conditions for Weiser products.
Preview Weiser Catalogue Complet de Quincaillerie de Porte et Serrures
Explorez le catalogue Weiser pour une vaste sélection de quincaillerie de porte, serrures électroniques et mécaniques, incluant les technologies SmartKey et Microban. Trouvez spécifications, finitions et prix.
Preview Weiser Lock Price Book 2020: Comprehensive Guide to Door Hardware
Explore the Weiser Lock Price Book 2020 for detailed information on a wide range of door hardware, including SmartKey technology, security features, and antimicrobial benefits. Find product specifications, ordering information, and terms of sale for residential and commercial applications.
Preview Weiser Lock Product Catalog and Specifications
Explore the comprehensive Weiser lock catalog, featuring SmartKey security technology and Microban antimicrobial protection. This guide details a wide range of handlesets, levers, knobs, and deadbolts, including models like SmartCode 10, Powerbolt, and Halo Touch. Find detailed product specifications, finishes, keying options, and ordering information for residential and commercial applications. Discover Weiser's commitment to quality and security in door hardware.
Preview Weiser SmartCode 5 Lever Programming and Troubleshooting Guide
A comprehensive guide to programming and troubleshooting the Weiser SmartCode 5 Lever electronic lock, covering mastercode setup, user code management, and common issues.
Preview Weiser Price Book 2022 - French Edition
This document is the 2022 French edition of the Weiser Price Book, detailing product information, specifications, and ordering guidelines for various lock types including deadbolts, handlesets, knobs, and more. It covers general information, packaging details, and ordering templates.
Preview Weiser SmartCode Keypad Electronic Locks Quick Start Guide and Installation Instructions
Comprehensive guide for installing, programming, and using Weiser SmartCode Keypad Electronic Locks, covering parts, tools, step-by-step installation, programming features, system alerts, and important safeguards.
Preview Weiser SmartCode 5 Touchpad Electronic Lever Installation and User Guide
Comprehensive guide for installing and using the Weiser SmartCode 5 Touchpad Electronic Lever, featuring Z-Wave Plus technology. Includes step-by-step instructions, troubleshooting, and technical specifications for smart home integration.