SUMERAIN S3235XI Shower System Installation Guide

Thank You

Dear Valued Customer,

SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions. We welcome any questions or comments you may have and look forward to assisting you in the future. If you have any questions regarding this product, call +1-866-203-0866 or email to supports@sumerain.com.

Sincerely,
SUMERAIN customer service department

Before Proceeding

1. Unpack your new product and ensure that all the parts are contained in the packaging. Keep the product in its original box until you are ready to install it.
2. Locate water supply inlets and shut off the water supply valves. These are usually found near the water meter. If you are replacing an existing unit, remove the old unit and clean the mounting surface thoroughly.
3. Observe all plumbing and building codes in your area.
4. It is recommended calling a professional if you are uncertain about installing this product.

Tools Recommended

• Philips Screwdriver
• Allen Wrench
• Adjustable Wrench
• Channel Locks
• Thread Sealant

Limited Lifetime Consumer Warranty

This product has been manufactured and tested to the highest quality standards by SUMERAIN sanitary Inc ("SUMERAIN"). This warranty is limited to SUMERAIN products which are purchased by a consumer in the China after Jan 1, 2010 and installed in China or the state which has SUMERAIN technical support department locally. If the faucet should leak or drip during normal use, SUMERAIN will, free of charge, mail to the purchaser the cartridge necessary to put the faucet in good working condition. If a defect is found in normal residential use, SUMERAIN will, at its election, repair, provide a replacement part or product, or make appropriate adjustment.

Who is Covered by the Warranty

This warranty extends to the original consumer purchaser only. This warranty is not transferable.

What is Covered by the Warranty

This warranty covers only your SUMERAIN manufactured product. SUMERAIN warrants this product against defects in material or workmanship. SUMERAIN will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. If SUMERAIN is unable to provide replacement, SUMERAIN may elect to provide a similar model upon close value.

Finish Warranty

It is the responsibility of the customer to check for any material finish defects before installation. SUMERAIN doesn't warranty these finishes after the fixture has been installed.

Electronic Faucets Warranty

SUMERAIN warrants that its electronic faucets, valves and controls to be free from manufacturing defects in material and workmanship under normal use for three (3) years from the date of purchase and waterflow impeller-dynamo (generate power for LED faucet) for six (6) months from the date of purchase.

Length of Warranty

Replacement or repaired parts of products will be covered for the term of this warranty as stated in the following two sentences. If you are a consumer who purchased the product for use primarily for personal, family, or household purposes, this warranty extends for 5 years since the product originally installed (Extend max 1 month From the date of purchase). If you purchased the product for use primarily for any other purpose, including, without limitation, a commercial purpose or is installed outside of US, or if the finish is gold, non-Vibrant or a painted or powder coated color finish this warranty extends only for one year, with respect to SUMERAIN and commercial products.

This Warranty Does Not Cover, and SUMERAIN Will Not Pay For:

• Conditions, malfunctions or damage not resulting from defects in material or workmanship.
• Conditions, malfunctions or damage resulting from normal wear and tear, improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration or the use of abrasive or caustic cleaning agents or "no-rinse" cleaning products, or the use of the product in any manner contrary to the product instructions. Conditions in the home such as excessive water pressure or corrosion.
• Labor or other expenses for the disconnection, deinstallation, or return of the product for warranty service, or for installation or reinstallation of the product.
• Accessories, connected materials and products (including but not limited in handshower flexible hose, spray flexible hose, handshower, shower head).

To Obtain Warranty Parts or Information

Contact your SUMERAIN retailer or contact technical service at: supports@sumerain.com

In requesting warranty service, you will need to provide:

1. The sales receipt or other evidence of the date and the place of purchase.
2. A description of the problem (Download URL: http://www.sumerain.com/download/servicerequest/sheet.pdf and fill out the Service Request Sheet).
3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured to specified address.

When warranty service is completed, any repaired or replacement product or part will be returned to you postage prepaid.

Exclusions and Limitations

Repair or replacement (or, in limited circumstances, refund of the purchase price) as provided under this warranty is the exclusive remedy of the purchaser. SUMERAIN neither assumes nor authorizes any person to create for it any obligation or liability in connection with this product. SUMERAIN shall not be liable to purchaser or any person for any incidental, special, or consequential damages, arising out of breach of this warranty or any implied warranty (including merchantability). Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal right, and you may have other rights which vary from state to state. You may be required by law to give us a reasonable opportunity to correct or cure any failure to comply before you can bring any action in court against us under the Magnusson-Moss warranty Act.

Product Instructions and Questions

Upon purchase or prior to installation, please carefully inspect your SUMERAIN product for any damage or visible defect. Prior to installing, always carefully study the enclosed instructions on the proper installation and the care and maintenance of the product. If you have questions at any time about the use, installation, or performance of your SUMERAIN product, or this warranty, please call or email us at +1-866-2030-866, supports@sumerain.com

Functions and Specification

Dimension

Front View of Shower:

Showerhead diameter: 9-1/16 inches

Shower arm diameter: 7/8 inches

Shower pipe diameter: 1-3/32 inches

Mounting base diameter: 2-3/8 inches

Side View of Shower:

Shower arm reach: 16-17/32 inches

Distance from wall to shower arm center: 16-3/8 inches

Distance from wall to showerhead center: 15-11/32 inches

Height from mounting base to hand shower holder: 23-13/16 inches

Height from mounting base to showerhead center: 30-5/16 inches

Distance from mounting base to showerhead center: 24-21/32 inches

Installation Steps

1. Before Proceeding

WARNING: (a) Read all the instructions completely before proceeding. SUMERAIN recommends calling a professional if you are uncertain about installing this product! This product should be installed in accordance with all local and state plumbing and building codes.

(b) Please measure the center interval of your existing shower head elbow to your valve trim and make sure the interval should be Min 30-23/32".

Diagram: A diagram shows a showerhead and a mounting point with a vertical arrow indicating a minimum distance of 30-23/32 inches.

2. Shut Off Water Supply

Locate water supply inlets and shut off the water supply valves. These are usually found near the water meter. If you are replacing an existing unit, remove the old unit and clean the mounting surface thoroughly.

3. Checking the Contents of the Box

Upon opening the box, check to ensure that all the following items are included.

Diagram: An exploded view of the shower system components with labels and quantities.

If any of these items are missing, please contact SUMERAIN consumer service by email to: supports@sumerain.com.

4. Installation Guide

4.1 Remove your existing showerhead.

Diagram: Illustration showing the removal of an existing showerhead.

4.2 Remove your existing shower arm.

Diagram: Illustration showing the removal of an existing shower arm.

4.3 Apply generous amount of PTFE Thread Sealant Tape to the NPT ends of supply nipple and install to the existing outlet elbow by S12 Allen Key.

Diagram: Illustration showing the application of thread sealant tape and installation of the supply nipple.

4.4 Slide hand shower holder off shower pipe.

Diagram: Illustration showing the hand shower holder being slid off the shower pipe.

4.5 Install shower pipe to diverter valve.

Diagram: Illustration showing the installation of the shower pipe to the diverter valve.

4.6 Remove covering of 3M Tape and position mount on marked locations of mounting base.

Diagram: Illustration showing the removal of 3M tape and positioning of the mount.

4.7 Apply adhesive (glue) on the area as indicated in below figure (Black pattern).

Diagram: Illustration showing where to apply adhesive.

4.8 Insert mounting base into the on/off valve and secure with set screw.

Diagram: Illustration showing the insertion of the mounting base into the on/off valve and securing with a set screw.

4.9 Install the shower pipe assembly to on/off valve, position diverter body and on/off valve body so shower pipe is plumb (vertical).

Diagram: Illustration showing the installation of the shower pipe assembly and positioning of the diverter and on/off valve bodies.

4.10 Push diverter valve body over supply nipple until flush against fitting. Remove covering of 3M Tape and apply pressure to mount for 30 seconds by pushing firmly against the wall. To ensure proper adhesion, allow one hour before using your Shower pipe system and keep area around the mount as dry as possible for the first 24 hours. Tape and glue will be fully cured after 24 hours.

WARNING: Wall surface must be clean of any residue and completely dry.

Diagram: Illustration showing the diverter valve body being pushed onto the supply nipple and pressure applied to the mount.

4.11 Loosen set screw on on/off valve body and remove the shower pipe assembly.

Diagram: Illustration showing loosening the set screw and removing the shower pipe assembly.

4.12 OPTIONAL: Secure mounting base with permanent wall anchors. Mark hole locations in mounting base. Drill 11/4" deep holes using 6mm (1/4") masonry/tile drill bit. Insert wall anchors (not included) and secure mounting base with screws.

CAUTION: LIVE PLUMBING IN WALL

Diagram: Illustration showing optional securing of the mounting base with wall anchors.

4.13 Slide escutcheon over diverter valve body and slide escutcheon over on/off valve body.

Diagram: Illustration showing the escutcheons being slid over the valve bodies.

4.14 Position shower pipe parallel to wall by sliding diverter valve body on supply nipple. Secure diverter valve body to supply nipple with set screw; Sliding on/off valve body on mounting base and secure it to mounting base with set screw;

Diagram: Illustration showing the positioning and securing of the shower pipe and valve bodies.

4.15 Push escutcheons onto finish wall and seal with silicon sealant.

Diagram: Illustration showing the escutcheons being pushed onto the wall and sealed.

4.16 Loosen set screw on diverter valve body and adjust the shower arm to desired position.

Diagram: Illustration showing loosening the set screw and adjusting the shower arm.

4.17 Secure swivel joint onto bottom of on/off valve body. Swivel joint should move freely side to side.

CAUTION: DO NOT OVERTIGHTEN

Diagram: Illustration showing the swivel joint being secured.

4.18 Insert flow restrictor and rubber washer into ends of shower head.

Diagram: Illustration showing the insertion of the flow restrictor and rubber washer into the showerhead.

4.19 Tighten shower head securely to shower arm.

Diagram: Illustration showing the showerhead being tightened to the shower arm.

4.20 Connect hex head of shower hose end to swivel joint.

Diagram: Illustration showing the connection of the shower hose to the swivel joint.

4.21 Connect tapered end of shower hose to hand shower.

Diagram: Illustration showing the connection of the shower hose to the hand shower.

4.22 Place hand shower into adjustable hanger(holder).

Diagram: Illustration showing the hand shower being placed into the adjustable holder.

4.23 Install Finish

Diagram: Illustration showing the final installation steps.

Cleaning Recommendation for SUMERAIN Products

Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.

Cleaning Materials for faucets and showers

• Acids are a necessary ingredient of cleaning materials for removing lime, however please pay attention to the following points when cleaning faucets and showers:
• Only use cleaning materials which are explicitly intended for this type of application.
• Never use cleaning materials which contain hydrochloric, formic, phosphoric, or acetic acid, as they cause considerable damage.
• Never mix one cleaning material with another.
• Never use cleaning materials or appliances with an abrasive effect, such as unsuitable cleaning powders, sponge pads, or micro fiber cloths.

Cleaning instructions for faucets and showers

• Please follow the cleaning material manufacturer's instructions. In addition, pay attention to the following points:
• Clean the faucets and showers as and when required.
• Use the amount of cleaning product and the amount of time recommended by the manufacturer. Do not leave the cleaner on the fixture longer than necessary.
• Regular cleaning can prevent calcification, if scale deposits are noticed on the faucet surface or the spout, you can clean it by a commercial limescale remover, such as Lime-Away® or CLR®. Dilute the remover according to the label instructions.
• The faucets might have some rusty if your faucet under hard water condition, please rub it with aluminum foil dipped in water until the surface is nice and smooth, and wipe it use a small amount of chrome polish or maybe something like car wax (such as Meguiar®, Turtle Wax®) or polish.
• For stainless steel faucet and spout both made of solid stainless, normally this finish has not protective coating on it (in particular waterfall spout inside), stainless steel is by its material nature very tarnish resistant, but by no means tarnish or stain proof. This finish might oxidize naturally over time and react to its environment. Keep your stainless fixture wiped clean and dry and use only a cleaner specifically made for stainless steel (such as Weiman®, CLR®).
• When using spray cleaners, spray first onto a soft cloth or sponge, never spray directly onto the faucet as droplets can enter openings and gaps and cause damage.
• After cleaning, rinse thoroughly with clean water to remove any cleaner residue.

Important

Residues of liquid soaps, shampoos, and shower foams can also cause damage, so rinse with clean water after using.

! Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage.

Components with damaged surfaces must be replaced or injury could result.

Damage caused by improper treatment is not covered under the warranty.

Contact Information

SUMERAIN INTERNATIONAL GROUP INC

Address: 1226 NORTH KING ST NUM 522
WILMINGTON, DE 19801
United States

Tel: +1(866)203-0866
Web: http://www.sumerain.com
E-mail: supports@sumerain.us

HONGKONG SUMERAIN SANITARY INDUSTRY CO., LIMITED

Address: FLAT/RM 3B 3/F BANK TOWER
NOS.351&353 KING'S ROAD
NORTH POINT
HK

Tel: +86-750-2731579
E-mail: supports@sumerain.com

SUMERAIN EUROPE SUPPORT

Address: Flottwellstr. 15
10785 Berlin,
Deutschland

Tel: +49 (0)30/23975898
E-mail: de@sumerain.com