Instruction Manual for Avigilon models including: ES-HD-IPM, ES-HD-IPM Outdoor HD Enclosure PoE Module, Outdoor HD Enclosure PoE Module, HD Enclosure PoE Module, Enclosure PoE Module, PoE Module
Product documentation
H4 Pro Camera Line - Avigilon
File Info : application/pdf, 8 Pages, 776.07KB
DocumentDocumentOutdoor HD Enclosure PoE Module ES-HD-IPM EN English - Instructions manual Contents ENGLISH 1 About this manual........................................................................................................... 3 1.1 Typographical conventions.....................................................................................................................3 2 Notes on copyright and information on trademarks................................................. 3 3 Safety rules ..................................................................................................................... 3 4 Identification ................................................................................................................... 4 4.1 Product description and type designation.........................................................................................4 4.2 Product markings ....................................................................................................................................4 5 Preparing the product for use ...................................................................................... 4 5.1 Unpacking and contents ........................................................................................................................4 5.1.1 Unpacking.................................................................................................................................................................4 5.1.2 Contents...................................................................................................................................................................4 5.2 Safely disposing of packaging material ............................................................................................4 6 Assembling and installing............................................................................................. 5 6.1 Installation ................................................................................................................................................. 5 6.1.1 How to open the housing .....................................................................................................................................5 6.1.2 Removal of the slide .............................................................................................................................................5 6.1.3 Installation of the cable glands ..........................................................................................................................5 6.1.4 Installation of the GEKO IRH illuminator (optional)........................................................................................5 6.1.5 Brackets and adaptors .........................................................................................................................................6 6.1.6 Installation of the version with double filter for air renewal .......................................................................6 6.1.7 Ethernet cable installation ...................................................................................................................................6 6.1.8 How to install the camera.................................................................................................................................... 7 6.1.9 Connection of the GEKO IRH illuminator (optional) ...................................................................................... 7 6.1.10 PoE cable connection .........................................................................................................................................8 6.1.11 Connection of the de-icing heating of the glass (optional) ........................................................................8 6.1.12 Connection of the blower with double filter for air renewal (optional)...................................................8 7 Configuration .................................................................................................................. 8 Instructions manual - English - EN 1 About this manual Before installing and using this unit, please read this manual carefully. Be sure to keep it handy for later reference. 1.1 Typographical conventions DANGER! Explosion hazard. Read carefully to avoid danger of explosion. DANGER! High level hazard. Risk of electric shock. Disconnect the power supply before proceeding with any operation, unless indicated otherwise. WARNING! Medium level hazard. This operation is very important for the system to function properly. Please read the procedure described very carefully and carry it out as instructed. INFO Description of system specifications. We recommend reading this part carefully in order to understand the subsequent stages. 2 Notes on copyright and information on trademarks The quoted names of products or companies are trademarks or registered trademarks. 3 Safety rules The manufacturer declines all responsibility for any damage caused by an improper use of the appliances mentioned in this manual. Furthermore, the manufacturer reserves the right to modify its contents without any prior notice. The documentation contained in this manual has been collected with great care, the manufacturer, however, cannot take any liability for its use. The same thing can be said for any person or company involved in the creation and production of this manual. · The device must be installed only and exclusively by qualified technical personnel. · Before any technical work on the appliance, disconnect the power supply. · Do not use power supply cables that seem worn or old. · Never, under any circumstances, make any changes or connections that are not shown in this handbook. Improper use of the appliance can cause serious hazards, risking the safety of personnel and of the installation. · Use only original spare parts. Non-original spare parts could cause fire, electrical discharge or other hazards. · Before proceeding with installation check the supplied material to make sure it corresponds to the order specification by examining the identification labels (4.2 Product markings, page 4). · Power supply to the product must be exclusively provided by the PoE cable (Power over Ethernet). · This device was designed to be permanently installed on a building or on a suitable structure. · When installing the device, comply with all the national standards. · Any device which could be installed inside the product must comply with the current safety standards. 3 EN - English - Instructions manual · If the installation is NEMA TYPE 4X, the installer must replace the cable glands of the product with NEMA TYPE 4X cable glands. · For all connections, use cables that are able to withstand temperatures of at least 75°C (167°F). · The product is designed to house only cameras that are properly certified. 4 Identification 4.1 Product description and type designation The ES-HD-IPM module exploits in an optimal way the POE and Hi-POE technology, using the power supplied by the Ethernet cable as the sole source of power for all the devices connected, thus ensuring the maximum efficiency and flexibility of the network system as well as user-friendly installation and low costs. The innovative IPM (Intelligent Power Management) system enables extremely quick and easy installation with the use of a single Ethernet connecting cable. The analog system, with previously installed camera housings, can be retrofitted on IPM system simply by changing the slide and the internal electronics. This enables the digital conversion, speeding up the installation and thereby minimizing costs and environmental impact. 4.2 Product markings See the label attached to the product. 5 Preparing the product for use Any change that is not expressly approved by the manufacturer will invalidate the guarantee. 5.1 Unpacking and contents 5.1.1 Unpacking When the product is delivered, make sure that the package is intact and that there are no signs that it has been dropped or scratched. If there are obvious signs of damage, contact the supplier immediately. Keep the packaging in case you need to send the product for repairs. 5.1.2 Contents Check the contents to make sure they correspond with the list of materials as below: · IPM module · RJ45 cable · Instructions manual 5.2 Safely disposing of packaging material The packaging material can all be recycled. The installer technician will be responsible for separating the material for disposal, and in any case for compliance with the legislation in force where the device is to be used. When returning a faulty product we recommend using the original packaging for shipping. 4 Instructions manual - English - EN 6 Assembling and installing The assembly and installation must be performed only by skilled personnel. 6.1 Installation 6.1.1 Preparing the Housing To retrofit the ES-HD-IPM module to Avigilon HD enclosures, the existing control board, slide and heater (if equipped) must first be removed. 1. Remove all electrical connections from the circuit board (02) 2. Remove the fixing screws and the circuit board. 3. Loosen the screws fastening the internal supply slide (01). 4. Move the internal slide by sliding it until the holes coincide with the slide locking screws. 5. Remove the internal slide. 6. The locking screws will be reused to secure the IPM module, do not discard these. 7. For ES-HD-HWS or ES-HD-HWS-LG housings, remove the heater plate (03) by unscrewing the two fixing screws. 01 02 03 6.1.3 How to install the camera It is possible to install only PoE type cameras. Mount the camera using the supplied screws (01) and spacers (02). Apply at least one spacer to guarantee electrical isolation between the slide and the camera. Position the camera lens close to the glass to avoid visual interference or optical reflections. Connect the camera to the J2 connector (PoE OUT) with the supplied cable (03). 03 02 01 Fig. 2 Refit the slide in its housing and fix the previously loosened screws. Fig. 1 6.1.2 Completing the External Installation Refer to the housing manual for details on installing the cable glands, mounting the brackets and adjusting the air intake valves. Fig. 3 5 EN - English - Instructions manual 6.1.4 PoE cable connection Connect the PoE cable from the Power Injector to the J1 connector. 7 Configuration Before powering the device, you must set the maximum power consumption of the housing operating on dip switch SW1. Fig. 3 Before powering the device, you must set the maximum power consumption of the housing operating on dip switch SW1 (7 Configuration, page 8). 6.1.5 Connection of the blower for ES-HD-CWS and ES-HD-CWS-LG Connect the fan cable to the J4 connector. Fig. 5 ABSORBED POWER CONFIGURATION SW1 Maximum power OFF PoE class 3 (13W max) ON Hi-PoE class 4 (25W max) Tab. 1 According to the absorbed power, the system can supply the options described in the table (Tab. 3, page 9). Fig. 4 6 Instructions manual - English - EN ES-HD-IPM : AVAILABLE MODELS AND FEATURES Operating temperature Injector Camera Heating -10°C / +60°C (14°F / 140°F) -10°C / +50°C (14°F / 122 F°) -30°C / +50°C (-22°F / +122°F) PoE classe 3 (13W) Hi-PoE class 4 (25W) PoE classe 3 (13W) Hi-PoE class 4 (25W) Hi-PoE class 4 (25W) Hi-PoE class 4 (25W) PoE max. class 2 (7W) PoE max. class 3 (13W) PoE max. class 2 (7W) PoE max. class 3 (13W) PoE max. class 3 (13W) PoE max. class 3 (13W) Tab. 2 Fan with double air filter 8 Switching on The automatic pre-heating (de-ice) process could be started whenever the device is switched on and the air temperature is below 0°C. This process is used to ensure that the device works properly even at low temperatures. The duration ranges between 60 and 120 minutes, depending on conditions. During the lighting phase the device reads the status of the dip switch and automatically detects all the connected options for the correct energy management of the housing. The 6 LEDs shown in the figure allow to check the product's operating status. Fig. 6 Refer to the table to identify the operating status. OPERATING STATUS LED LED Apparatus Status Status LD1 (Po- Off wer) On The device is not powered The device is correctly powered LD2 Off (Camera) The camera is not connected or Cold Start is active On The camera is correctly powered 1 flashing The camera has a low identification resistance 2 flashings The camera has a high identification resistance 5 flashings The camera has an excessive energy consumption 9 flashings The camera requires more energy than the available LD3 (Not used) LD4 (He- Off ater) Heating is not available or power available is not sufficient 1 flashing Heating is inactive On Heating is active LD5 (Not used) LD6 Off (Cold Start) 1 flashing Heating is not available The pre-heating procedure is inactive On The pre-heating procedure is underway Tab. 3 7 EN - English - Instructions manual 9 Cleaning 9.1 Window and plastic cover cleaning (PC) Avoid ethyl alcohol, solvents, hydrogenated hydrocarbide, strong acid and alkali. Such products may irreparably damage the surface. Surface dirt should be rinsed away with water and then the window cleaned with a neutral soap diluted with water, or specific products for spectacle lens cleaning. These should be applied with a soft cloth. 10 Disposal of waste materials This symbol mark and recycle system are applied only to EU countries and not applied to the countries in the other area of the world. Your product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please dispose of this equipment at your local Community waste collection or Recycling centre. In the European Union there are separate collection systems for used electrical and electronic products. 11 Technical data 11.1 Mechanical Unit weight: 0.6 kg (1.32 lb) 11.2 Electrical Power absorbed in input: PoE class 3 (13W) or HiPoE class 4 (25W) selectable from dip switch Available power for camera (PoE IN class 3): PoE classe 2 (7W) Available power for camera (Hi-PoE IN class 4): PoE class 3 (13W) with Ton -10°C ±2°C "cold start" function Data line: 10/100Base-T Heating: 8W, electronically controlled, Ton 20°C±2°C (68°F±4°F), Toff 23°C±2°C (73.4°F±4°F) Fan with thermostat for camera cooling for versions with double air filter: Ton 35°C±2°C (95°F±4°F), Toff 32°C±2°C (89.6°F±4°F) Compatible with IEEE 802.3af, IEEE 802.3at/PoE Plus © -- 2014 Avigilon Corporation. All rights reserved. Unless expressly granted in writing, no license is granted with respect to any copyright, industrial design, trademark, patent or other intellectual property rights of Avigilon Corporation or its licensors. AVIGILON, CAPTURE IT WITH CLARITY, HDSM, HIGH DEFINITION STREAM MANAGEMENT (HDSM), THE BEST EVIDENCE and LIGHTCATCHER are unregistered and/or registered trademarks of Avigilon Corporation in Canada and other jurisdictions worldwide. Other product names mentioned herein may be the unregistered and/or registered trademarks of their respective owners. TM and ® are not used in association with each trademark in this document. 8Adobe InDesign CS6 (Windows) Adobe PDF Library 10.0.1