MAUL Lighting Safety Instructions and Symbol Guide

General Safety Instructions

• Read all included operating instructions and information carefully.
• Follow all warnings indicated in the documentation and on the device.
• Use the luminaire only when no technical defects are clear, be aware of dangers and risks.
• Observe national safety regulations for installation and use of the luminaires.
• Install luminaires only on suitable ceilings indoors.
• Install the lamp only on a suitable surface.
• Use only mounting materials suitable for the surface.
• This lamp is intended to illuminate indoor rooms and work areas.
• Mount luminaires only in dry and closed spaces.
• Do not use in potentially explosive atmospheres, as this can lead to explosions and death or serious injury.
• Installation, repairs, and dismantling must only be carried out by a qualified electrician, unless otherwise stated.
• Connect the luminaire to an earthed power supply.
• Compare the available mains voltage with the operating voltage and frequency specified on the nameplate and ensure they are identical.
• Damaged luminaires may no longer be used.
• Always disconnect the lamp from the mains before working on it.
• The luminaire may not be altered or modified.
• Do not hang or attach anything to the lamp.
• Do not cover the luminaire.
• Do not leave children unattended with the luminaire; it is not suitable for children.
• Dispose of packaging according to local regulations and follow any special disposal instructions.
• Disconnect the lamp from the mains and allow it to cool down before cleaning and maintenance.
• Clean only with a dry, soft, and lint-free cloth.
• If the connection cable is damaged, it must be replaced or repaired exclusively by the manufacturer, service agent, or a similarly qualified person (electrician) to avoid a hazard.

Symbol Explanations

Electrical Protection Class I

Protective earthing ⛋

Electrical Protection Class II

No protective conductor, as there is sufficient insulation between live and tangible parts. ⛋⛋

Electrical Protection Class III

Tangible extra low voltage. ⛋⛋⛋

Suitable for direct assembly

Lamps suitable for direct assembly on normally flammable assembly surfaces.

Minimum distance

Minimum distance to illuminated surfaces should not be undercut. ⟁ 0.1m

Hot Surface Warning

Warning! Hot surface. The luminaire head may exceed the specified temperature. ?️

Self-Protected Bulb

Self-protected bulb, can be used in lamps without extra protection cover. ?

Indoor Use Only

The luminaire should only be used in dry areas indoors.

Replace Damaged Cover

Each damaged protection cover should be exchanged immediately. ❌

Fail-Safe Transformer

Transformer is out of order after a short circuit.

Short Circuit Safety Transformer

In case of error, the entry circuit may be interrupted where necessary.

Independent Devices

Independent devices for lamps (e.g., power supply, ballast).

IP Protection

IP20: Protected against touch and solid foreign objects ≥ 12.5 mm in diameter. ?❌

Risk of Electric Shock

Caution, risk of electric shock. ⚡

Hazardous Area

Hazardous area, general. ⚠️

Dimmable

Dimmable. ⚙️

Not Dimmable

Not dimmable. ⚙️❌

SELV

Safety Extra Low Voltage.

Beam Angle

Half intensity angle (beam angle). 100°

Qi Compatible

Qi compatible device. ?

Qualified Electrician

Skilled electrician. ⛋

Observe Instructions

Follow instructions. ?

Operating Device Replaceable

Operating device replaceable.

Operating Device Replaceable by Electrician

Operating device replaceable by electrician.

Operating Device Not Replaceable

Operating device not replaceable.

LED Light Source Replaceable

LED light source replaceable.

LED Light Source Replaceable by Electrician

LED light source replaceable by electrician.

LED Light Source Not Replaceable

LED light source not replaceable.

Light Source Replaceable

Light source replaceable.

Light Source Replaceable by Electrician

Light source replaceable by electrician.

CE Marking

CE

Manufacturer Declaration

MAUL declares that these lamps conform to the European Directives and to the product-specific directives.

Disposal

Do not dispose of with unsorted household waste; collect as electrical waste at designated facilities. ♻️

Risk Group 2

This symbol denotes devices classified in risk group 2 (RG2). Products with this symbol can cause damage to the eyes through extended, deliberate viewing. Avoid direct eye contact with the light of individual LEDs. ?️‍?️