Suprema | Security & Biometrics
Suprema | Security & Biometrics슈프리마 | Security & Biometrics
Installation Guide for Suprema models including: XPD2-MDB2, TKWXPD2-MDB2, TKWXPD2MDB2, XPass D2 RFID Card Reader, RFID Card Reader, Card Reader
Suprema Inc. XPD2-MDB2 TKWXPD2-MDB2 TKWXPD2MDB2 xpd2 mdb2
File Info : application/pdf, 17 Pages, 2.60MB
DocumentDocumentXPass D2 INSTALLATION GUIDE Version 1.07 English EN 101.00.XPD2-MDB, XPD2-GDB, XPD2-GKDB V1.07A CONTENTS Safety instructions Instructional icons Introduction Components Name and function of each part Installation Fixing the bracket and the product Power supply connection RS-485 connection Wiegand and other cable connections Restoring the Factory Defaults Resetting the baud rate of RS-485 2 FCC compliance information 13 2 EU Declaration of Conformity (CE) 13 4 4 Appendices 14 5 Disclaimers 14 Copyright notice 14 7 Open Source License 15 7 9 9 10 10 10 Product specifications 11 Dimensions 12 XPD2-MDB 12 XPD2-GDB, XPD2-GKDB 12 Safety instructions Safety instructions Please read this safety instructions before you use the product to prevent injury to yourself and others and to prevent property damage. The term `product' in this manual refers to the product and any items provided with the product. Instructional icons Warning: This symbol indicates situations that could result in death or severe injury. Caution: This symbol indicates situations that may result in moderate injury or property damage. Note: This symbol indicates notes or additional information. Warning Installation Do not install or repair the product arbitrarily. · This may result in electric shock, fire, or product damage. · Damages caused by any modifications or failure to follow installation instructions can void your manufacturer's warranty. Do not install the product in a place with direct sunlight, moisture, dust, soot, or a gas leak. · This may result in electric shock or fire. Install the product in a well-ventilated and cool place away from direct sunlight to prevent overheating when installing it outside. Do not place the product inside the sealed enclosure when installing it outside. · It increases the internal temperature of the enclosure and this may result in electric shock, fire, or malfunction. Do not install the product in a location with heat from an electric heater. · This may result in fire due to overheating. Install the product in a dry location. · Humidity and liquids may result in electric shock or product damage. Do not install the product in a location where it will be affected by radio frequencies. · This may result in fire or product damage. Operation Keep the product dry. · Humidity and liquids may result in electric shock, fire, or product damage. Do not use damaged power supply adaptors, plugs, or loose electrical sockets. · Unsecured connections may cause electric shock or fire. Do not bend or damage the power cord. · This may result in electric shock or fire. 2 Safety instructions Caution Installation Do not install the product under direct sunlight or UV light. · This may result in product damage, malfunction, discoloration, or deformation. Do not install the power supply cable in a location where people pass by. · This may result in injury or product damage. Do not install the product near magnetic objects, such as a magnet, TV, monitor (especially CRT), or speaker. · The product may malfunction. Do not seal around the product with silicone, etc. when installing it on the wall. · The product may malfunction. Keep the minimum distance between products when installing multiple products. · The product may be affected by radio frequencies emitted by other products and the product may malfunction. Use the IEC/EN 62368-1 approved power adaptor that supports higher power consumption than the product. It is highly recommended to use the power adaptor sold by Suprema. · If the right power supply is not used, the product may malfunction. It is recommended to use the enclosure if the product is installed outside. · The product may malfunction if the water-resistant and dust-resistant features are damaged. Operation Do not drop the product or cause impacts to the product. · The product may malfunction. Do not disconnect the power supply while upgrading the firmware of the product. · The product may malfunction. Do not disclose the password to others and change it regularly. · This may result in illegal intrusion. Do not store your product in very hot or very cold places. It is recommended to use your product at temperatures from -35 °C to 65 °C. · The product may malfunction. When cleaning the product, mind the following. · Wipe the product with a clean and dry towel. · If you need to sanitize the product, moisten the cloth or the wipe with a proper amount of rubbing alcohol and gently clean all exposed surfaces including fingerprint sensor. Use rubbing alcohol (containing 70% Isopropyl alcohol) and a clean, non-abrasive cloth like lens wipe. · Do not apply liquid directly to the surface of the product. Do not use the product for anything other than its intended use. · The product may malfunction. RTC battery Discard the battery according to the appropriate regional or international waste regulations. Discard the battery according to the appropriate regional or international waste regulations. 3 Introduction Components Introduction Device and Wall Bracket (XPD2-MDB) Device and Wall Bracket (XPD2-GDB) Device and Wall Bracket (XPD2-GKDB) PVC Anchor x2 39.8 Fixing Screw x2 Bracket Fixing Screw (Star Shaped) 132.2 83.5 XPD2-M XP2-M Drilling Template Shrink Tube 120 resistor XPass D2 XPass D2 MDB 201.00.XPD2 V1.06A Quick Guide (XPD2-MDB) XPass D2 XPass D2 GDB 201.00.XP2 V1.03A Quick Guide (XPD2-GDB) XPass D2 XPass D2 GKDB 201.00.XPD2 V1.03A Quick Guide (XPD2-GKDB) Open Source Software Linux Kernel GPL BoringSSL Original SSLeay AOSP Apache G 306.00 V1.00A Open Source Software Guide · Components may vary according to the installation environment. · When assembling the product with the bracket, you can use the included bracket fixing screw (Star Shaped) instead of the product fixing screw for enhanced security. 4 Name and function of each part LED Indicator RF card and mobile access card authentication unit Introduction Keypad Reset Button Cable Name Description LED Indicator RF card and mobile access card authentication unit Indicates the operational status of the device with the color of the LED. · Green solid: Authentication success · Red solid: Authentication failure · Blue/Sky blue blinking: Normal operation · Blue/Green blinking: When initializing network settings · Green blinking: Waiting for an input · Green/White blinking: Connecting with the Airfob Pass (BLE) application of Suprema · White blinking: Connecting with the Device Manager application of Suprema Reads RF cards for entering and exiting. Reset button Initialize the device. Cable · Power cable · RS-485 cable · Wiegand output cable · LED input cable · Beep Input cable · Tamper cable 5 Introduction Keypad Used to authenticate by entering the card ID directly. If you want to enter the ID directly, change the authentication method settings in BioStar 2. · 0 ~ 9: Enters number. · : Separates the FC code from the ID when entering the Wiegand card ID. · : Used to finish entering. Only the XPD2-GKDB model supports the keypad. Cables This document describes cable information based on the shape of the XPD2-MDB model. The same cable configuration is also used for XPD2-GDB and XPD2-GKDB models. 10 9 8 7 6 5 4 3 2 1 Pin Name Color 1 PWR +VDC Red 2 GND Black (White stripe) 3 485 TRXN Yellow (Black stripe) 4 485 TRXP Blue (White stripe) 5 WG D0 Green 6 WG D1 White 7 LED RED Orange 8 LED GRN Brown 9 BEEP Purple 10 TMPR Gray 6 Installation Installation Fixing the bracket and the product This document describes the installation method using XPD2-MDB model. Install XPD2-GDB and XPD2-GKDB models in the same way. 1 Determine the correct position to install the bracket using the provided drilling template. Fix the bracket firmly using fixing screws through the bracket to the position where XPass D2 will be installed. · If installing XPass D2 on a concrete wall, drill holes, insert PVC anchors, and fix them with fixing screws. · To avoid RF interference, a minimum separation distance must be maintained. XPD2-MDB Wall Wall thickness Wall Distance 400 mm Wall thickness 100 mm 120 mm 150 mm XPD2-GDB, XPD2-GKDB Distance 360 mm 360 mm 300 mm Wall thickness Distance Wall Wall 430 mm Wall thickness 100 mm 120 mm 150 mm Distance 400 mm 380 mm 380 mm · When using Suprema Mobile Access, install a minim7um distance of 1 m between devices to avoid BLE interference. 2 Install XPass D2 onto the fixed bracket. Installation 3 Assemble XPass D2 with the bracket by rotating the product fixing screw. · When assembling the product with the bracket, you can use the included bracket fixing screw(Star Shaped) instead of the product fixing screw for enhanced security. 8 Power supply connection XPass D2 can be used as an RFID card reader by connecting to a master device or a CoreStation. Installation 1 - PWR +VDC 2 - GND Red Black (White stripe) 1 DC power 2 XPass D2 · Use the IEC/EN 62368-1 approved power adaptor that supports higher power consumption than the product. If you wish to connect and use another device to the power supply adaptor, you should use an adaptor with a current capacity which is the same or larger than the total power consumption required for the terminal and another device. RS-485 connection 1 DC power 2 Control device 3 1 - PWR +VDC 2 - GND 3 - 485 TRXN 4 - 485 TRXP Red Black (White stripe) Yellow (Black stripe) Blue (White stripe) 4 XPass D2 · Use an AWG24 twisted pair with a maximum length of 1.2 km for the RS-485 cable. · If connecting with a RS-485 daisy chain, connect the termination resistor (120 ) to both ends of the daisy chain connection. If connected to the middle line, the signal level becomes smaller and the communication performance will deteriorate. Make sure to connect it to both ends of the daisy chain connection. 9 Wiegand and other cable connections 1 - PWR +VDC 2 - GND 5 - WG D0 6 - WG D1 7 - LED RED 8 - LED GRN 9 - BEEP 10 - TMPR Red Black (White stripe) Green White Orange Brown Purple Gray DC power Control device Installation XPass D2 1 2 5 6 7 8 9 10 Restoring the Factory Defaults This will reset all settings stored on the device. 1 Turn the power on. 2 Press the reset button three times quickly. 3 When the green LED is blinking, press the reset button again. Resetting the baud rate of RS-485 1 Turn the power on. 2 Press and hold the reset button for more than 2 seconds. When the device change to setup mode, the green LED is blinking. 3 Depending on the number of times the reset button was pressed, the baud rate changes. You can recognize the baud rate according to the LED color. The number of times Baud Rate LED Color 1 9600 Cyan 2 19200 Blue 3 38400 Magenta 4 57600 White 5 115200 Red 4 The LED blinks for 5 seconds with the color set as the above. The baud rate is set once you hear a beep sound. · If you do not press the reset button after changing to the setup mode, the baud rate is set to 115200. 10 Product specifications Product specifications Category Feature Credential General RF Option RF read range** Mobile CPU Memory Crypto chip LED Sound Operating temperature Storage temperature Operating humidity Storage humidity Dimension (W x H x D) Weight Interface Electrical IP rating IK rating Certificates RS-485 Wiegand LED Beep Tamper Power LED, Beep input VIH LED, Beep input VIL LED, Beep Pull-up resistance Wiegand output VOH Wiegand output VOL Wiegand output Pull-up resistance Specifications XPD2-MDB XPD2-GDB XPD2-GKDB 125 kHz EM & 13.56 MHz MIFARE, MIFARE Plus, DESFire EV1/EV2*, FeliCa MIFARE/DESFire/EM: 50 mm, FeliCa: 30 mm NFC, BLE 80 MHz 512 KB Flash + 160 KB RAM Supported Multi-color Multi-tone Buzzer -35°C to 65°C -40°C to 70°C 0 % to 95 %, non-condensing 0 % to 95 %, non-condensing 48 x 145 x 27 80 x 130 x 25 80 x 130 x 25 · Device: 117 g · Bracket: 30 g (Including washer and bolt) · Device: 140 g · Bracket: 52 g (Including washer and bolt) · Device: 145 g · Bracket: 52 g (Including washer and bolt) IP65, IP67 IK08 CE, FCC, KC, RoHS, REACH, WEEE, SIG, SIA OSDP Verified 1ch 1ch 2ch 1ch Supported Voltage: DC 12 V, Current: Max. 300 mA Min. 3 V, Max. 5 V Max. 1 V 4.7k (The input ports are pulled up with 4.7k.) Min. 4.8 V Max. 0.2 V Internally pulled up with 1 k * DESFire EV2 cards are supported by having backward compatibility of DESFire EV1 cards. CSN and smart card functions are compatible with XPass D2. ** RF read range will vary depending on the installation environment. 11 Dimensions XPD2-MDB Product specifications (Unit: mm) * The tolerance is ±0.3mm. 144.7 132.2 39.8 48 27 XPD2-GDB, XPD2-GKDB 130 80 116.1 72.4 25 12 FCC compliance information FCC compliance information THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement (Part 2.1091) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. EU Declaration of Conformity (CE) This product is CE marked according to the provisions of the Radio Equipment Directive (RED) 2014/53/EU. Hereby, Suprema Inc. declares that this product is in compliance with the essential requirements and other relevant provisions of Radio Equipment Directive (RED) 2014/53/EU. · Bluetooth Transmit Power: -5.96dBm · Bluetooth Frequency: 2402~2480 MHz · NFC Frequency: 13.56 MHz · RFID Frequency: 125 kHz For more information, contact us at the following contact information. Suprema Inc. Website: https://www.supremainc.com Address: 17F Parkview Tower, 248, Jeongjail-ro, Bundang- gu, Seongnam-si, Gyeonggi-do, 13554, Rep. of KOREA Tel: +82-31-783-4502 / Fax: +82-31-783-4503 13 Appendices Appendices Disclaimers · Information in this document is provided in connection with Suprema products. · The right to use is acknowledged only for Suprema products included in the terms and conditions of use or sale for such products guaranteed by Suprema. No license, express or implied, by estoppel or otherwise, to any intellectual property is granted by this document. · Except as expressly stated in an agreement between you and Suprema, Suprema assumes no liability whatsoever, and Suprema disclaims all warranties, express or implied including, without limitation, relating to fitness for a particular purpose, merchantability, or noninfringement. · All warranties are VOID if Suprema products have been: 1) improperly installed or where the serial numbers, warranty date or quality assurance decals on the hardware are altered or removed; 2) used in a manner other than as authorized by Suprema; 3) modified, altered or repaired by a party other than Suprema or a party authorized by Suprema; or 4) operated or maintained in unsuitable environmental conditions. · Suprema products are not intended for use in medical, lifesaving, life-sustaining applications, or other applications in which the failure of the Suprema product could create a situation where personal injury or death may occur. Should you purchase or use Suprema products for any such unintended or unauthorized application, you shall indemnify and hold Suprema and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Suprema was negligent regarding the design or manufacture of the part. · Suprema reserves the right to make changes to specifications and product descriptions at any time without notice to improve reliability, function, or design. · Personal information, in the form of authentication messages and other relative information, may be stored within Suprema products during usage. Suprema does not take responsibility for any information, including personal information, stored within Suprema's products that are not within Suprema's direct control or as stated by the relevant terms and conditions. When any stored information, including personal information, is used, it is the responsibility of the product users to comply with national legislation (such as GDPR) and to ensure proper handling and processing. · You must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Suprema reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. · Except as expressly set forth herein, to the maximum extent permitted by law, the Suprema products are sold "as is". · Contact your local Suprema sales office or your distributor to obtain the latest specifications and before placing your product order. Copyright notice The copyright of this document is vested in Suprema. The rights of other product names, trademarks and registered trademarks are vested in each individual or organization that owns such rights. 14 Appendices Open Source License MIT License Permission is hereby granted, free of charge, to any person obtaining a copy of this software and associated documentation files (the "Software"), to deal in the Software without restriction, including without limitation the rights to use, copy, modify, merge, publish, distribute, sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is furnished to do so, subject to the following conditions: The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. IC compliance information Industry Canada Statement This device complies with RSS-247&210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-247&210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Industry Canada Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. Déclaration d'exposition aux radiations Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non con trôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. 15 Suprema Inc. 17F Parkview Tower, 248, Jeongjail-ro, Bundang-gu, Seongnam-si, Gyeonggi-do, 13554, Rep. of KOREA Tel: +82 31 783 4502 | Fax: +82 31 783 4503 | Inquiry: sales_sys@supremainc.com For more information about Suprema's global branch offices, visit the webpage below by scanning the QR code. https://supremainc.com/en/about/global-office.asp © 2022 Suprema Inc. Suprema and identifying product names and numbers herein are registered trade marks of Suprema, Inc. All non-Suprema brands and product names are trademarks or registered trademarks of their respective companies. Product appearance, build status and/or specifications are subject to change without notice.