EK-Quantum Velocity2 D-RGB - LGA 1700 User Guide

General Information on Water Block Compatibility

This CPU liquid cooling unit is pre-assembled for use with modern Intel desktop socket type motherboards. By default (out of the box) this water block supports the following CPU sockets: Intel LGA-1700.

Box Contents

The mounting mechanism is universal and you may not need all the screws.

• Mounting Mechanism
• Allen Key 2 mm (1 pc)
• Allen Key 2.5 mm (1 pc)
• EK-Quantum Velocity2 D-RGB 1700
• Thermal grease (1 pc)

Water Block Dimensions

Water Block Dimensions:

• Length: 94.5 mm
• Width: 61.5 mm
• Height: 33.5 mm
• Additional dimensions: 15.3 mm, 20.5 mm, 33 mm, 9 mm, 6 mm, 3.5 mm

Backplate Dimensions:

• Length: 78 mm
• Width: 78 mm

Technical Specifications and Water Block Parts

Preparing the Motherboard

STEP 1 If already installed, please remove the motherboard from your computer and place it on an even surface.

STEP 2 Cleaning the CPU: Wipe the IHS (Integrated Heat Spreader) clean using a non-abrasive cloth or Q-tip.

STEP 3 Applying thermal compound: Once clean, apply a line of Thermal Compound on one edge of the IHS and use a credit card or similar to spread it evenly. The layer of Thermal Compound must be thin and even in thickness over the entire surface of the IHS. Excessive or irregular application may lead to poor performance. This method works for Thermal Grizzly Hydronaut Thermal Compound as supplied with all Velocity2 CPU Water Blocks.

Installing the Water Block

STEP 1 Unscrew the pre-installed backplate from the backside of the CPU using an Allen Key 2.5 mm and save it for the later steps.

STEP 2 Before placing the water block, it is mandatory to remove the protective foil from the backside of the CPU socket area.

STEP 3 Position the CPU Water Block onto the Motherboard, ensuring the holes are aligned. Double-check the layer of the Thermal Grease before placing the water block onto the motherboard. The maximum recommended torque for fastening is 0.6 Nm.

STEP 4 After placing the water block, attach the stored backplate on the backside of the motherboard using Allen Key 2.5 mm. Start fastening the backplate screws in a cross pattern. Do not tighten fully until all of the nuts are partially screwed in. The Allen Key 2.5mm must be used in a standing position to avoid cracking the mounting screws during tightening. EK recommends using the EK-Loop Torque Screwdriver - 0.6Nm: EK-Loop Torque Screwdriver. Make sure to orientate the backplate as illustrated. Incorrect installation of the backplate may result in damage to the motherboard.

STEP 5 With EK-Velocity2 series water blocks, it is mandatory to use the bottom port as the INLET. Mixing the ports may result in poor thermal performance of the water block. Tighten the fittings in a clockwise direction until the gasket underneath is compressed. The installation of the Velocity2 water block is now complete.

Connecting the D-RGB LED Strip

STEP 1 Plug the 3-pin connector from the water block's D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, empty, Ground. Please ensure that the arrow indicated on the connector is plugged into the +5V line as indicated on your motherboard. If you connect the LED Diode to a 12V RGB HEADER, you can damage the LEDs. Failure to do so will damage your motherboard or LED strip.

Support and Service

In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact EK Water Blocks customer support at: EKWB Customer Support. For spare parts orders, refer to the page with "TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS" where you can find the EAN number of each part you might need. Include the EAN number with the quantity in your request. Mounting Mechanism EAN can be found under "BOX CONTENTS". Thermal pads are readily available in the EK shop.

Social Media

• EKWaterBlocks
• @EKWaterBlocks
• ekwaterblocks
• EKWBofficial
• ekwaterblocks