ED-HMI3010-101C Application Guide

Contact Us

Thank you very much for purchasing and using our products, and we will serve you wholeheartedly. As one of the global design partners of Raspberry Pi, EDA Technology is committed to providing hardware solutions for IOT, industrial control, automation, green energy and artificial intelligence based on the Raspberry Pi technology platform.

You can contact EDA Technology Co.,LTD in the following ways:

Address: Room 301, Building 24, No.1661 Jialuo Highway, Jiading District, Shanghai

Mail: sales@edatec.cn

Phone: +86-18217351262

Website: https://www.edatec.cn

Technical Support:

Mail: support@edatec.cn

Phone: +86-18627838895

Wechat: zzw_1998-

Copyright Statement

ED-HMI3010-101C and its related intellectual property rights are owned by EDA Technology Co.,LTD. EDA Technology Co.,LTD owns the copyright of this document and reserves all rights. Without the written permission of EDA Technology Co.,LTD, no part of this document may be modified, distributed or copied in any way or form.

Disclaimer

EDA Technology Co.,LTD does not guarantee that the information in this manual is up to date, correct, complete or of high quality. EDA Technology Co.,LTD also does not guarantee the further use of this information. If material or non-material related losses are caused by using or not using the information in this manual, or by using incorrect or incomplete information, as long as it is not proved that it is the intention or negligence of EDA Technology Co.,LTD, the liability claim for EDA Technology Co.,LTD can be exempted. EDA Technology Co.,LTD expressly reserves the right to modify or supplement the contents or part of this manual without special notice.

Foreword

Related Manuals

Users can visit the following website for more information: https://www.edatec.cn

Reader Scope

• Mechanical Engineer
• Electrical Engineer
• Software Engineer
• System Engineer

Related Agreement

Symbolic Convention

Safety Instructions

• This product should be used in an environment that meets the requirements of design specifications, otherwise it may cause failure, and functional abnormality or component damage caused by non-compliance with relevant regulations are not within the product quality assurance scope.
• EDA Technology will not bear any legal responsibility for personal safety accidents and property losses caused by illegal operation of products.
• Please do not modify the equipment without permission, which may cause equipment failure.
• When installing equipment, it is necessary to fix the equipment to prevent it from falling.
• If the equipment is equipped with an antenna, please keep a distance of at least 20cm from the equipment during use.
• Do not use liquid cleaning equipment, and keep away from liquids and flammable materials.
• This product is only supported for indoor use.

1 Install OS

This chapter introduces how to download OS file and flash SD card.

• Download OS File
• Flash SD Card

1.1 Download OS File

If the operating system is damaged during use, you need to re-download the latest version of the system image and flash it.

1.2 Flash SD Card

ED-HMI3010-101C starts the system from the SD card by default. If you need to flash the latest system, you need to flash the system image to the SD card. It is recommended to use the official Raspberry Pi flashing tool, and the download path is as follows:

Raspberry Pi Imager: https://downloads.raspberrypi.org/imager/imager_latest.exe

Preparation:

• The download and installation of the flashing tool to the computer has been completed.
• A card reader has been prepared.
• The OS file to be flashed has been obtained.
• The device case has been opened and the SD card of ED-HMI3010-101C has been obtained. For detailed operations, please refer to 2.1 Open Device Case and 2.2 Pull Out SD Card.

Steps:

The steps are described using Windows system as an example.

1. Insert the SD card into the card reader, and then insert the card reader into the USB port of PC.
2. Open Raspberry Pi Imager. The interface shows options for 'Operating System' and 'Storage'. Select "CHOOSE OS" and then "Use Custom" in the pop-up pane.
3. According to the prompt, select the downloaded OS file under the user-defined path and return to the main interface.
4. Click "CHOOSE STORAGE", select the SD card of ED-HMI3010-101C in the "Storage" interface, and return to the main interface.
5. Click "WRITE" and select "Yes" in the pop-up prompt box to start writing the OS. The 'Raspberry Pi Imager' window displays the writing progress.
6. After the OS writing is completed, the file will be verified. The 'Raspberry Pi Imager' window shows the verification progress.
7. After the file verification is completed, the prompt box "Write Successful" pops up, and click "CONTINUE" to finish flashing SD card.
8. Close Raspberry Pi Imager, remove the card reader.
9. Insert the SD card into the Raspberry Pi 5 and close the device case (for detailed operations, please refer to 2.3 Insert SD Card and 2.4 Close Device Case), and then power on again.

2 Open and Close Case

This chapter introduces the operations for opening/closing the device case and inserting/removing the SD card.

• Open Device Case
• Pull Out SD Card
• Insert SD Card
• Close Device Case

2.1 Open Device Case

Preparation:

A cross screwdriver has been prepared.

Steps:

Use a screwdriver to loosen the 4 M3 screws on the ED-HMI3010-101C metal case counterclockwise, and remove the metal case. The back of the device shows four screw locations and external ports. After removing the cover, internal components, ribbon cables, and the SD card slot are visible.

2.2 Pull Out SD Card

Preparation:

• The device case has been open.
• A pair of tweezers is ready.

Steps:

1. Find the location of the SD card. It is a small slot on the side of the internal board.
2. Use tweezers to hold the SD card and pull it out. The image shows the SD card being removed from its slot.

2.3 Insert SD Card

Preparation:

• The device case has been open.
• SD card has been pulled out.

Steps:

1. Find the location of the SD card slot.
2. Insert the SD card into the corresponding card slot with the contact side facing up, making sure it will not fall out. The image shows the SD card being inserted into the slot.

2.4 Close Device Case

Preparation:

A cross screwdriver has been prepared.

Steps:

Cover the case, insert 4 M3 screws, and tighten clockwise to secure the case. The back of the device shows the screw holes and ports where the cover attaches.