Instruction Manual for myFirstech models including: DL-CH12 Jeep Cherokee PTS, DL-CH12, Jeep Cherokee PTS, Cherokee PTS, PTS
FTI-CDP1 | MyFirstech Install
FTI-CDP1: Vehicle Coverage and Preparation Notes Make Model DL-CH12 Jeep Cherokee PTS Year 2014-18 Install Type 5 CAN OBD-II Lights Park / Auto Type B2 IGN PINK RAP I/O Changes Green White/Blue NO N/A FIRMWARE: This installation requires BLADE-AL(DL)-CH12, flash module and update the controller firmware before installing. INSTALLATION: Type 5 vehicles use CAN connections in harness at OBD-II connector, the CAN extension cable is not required . IGNITION: Type 5 ignition is available at the Trailer Pack Connector (black, 13-pin connector, pin #8, pink), located to the left of the steering column. FTI-CDP1 - Installation and Configuration Notes A REQUIRED CONNECTION (OBD-II CAN) B NOT REQUIRED (CAN extension) C NO CONNECTION D REQUIRED CONNECTION (IGN) ZIIIOIIIOIIIILIIIAIINIIIIDIIIEIIIRIIIIIIIIIIIIIIIIIIIIIIIIIIIII 2001 DEREK Est. IIIIIIIII R KIDS foRrEAD GOOD TECAN'T CEN AND WHO HO W WANNA LEARN TO IIIIIIIII FEATURE COVERAGE CM7000/7200 Cut loop for A/T CM7X00 CM-900S/900AS CM900AS/900S Jumper IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII D O OTHER STUFF GOOD TOO IMMOBILIZER DATA ARM OEM ALARM DISARM OEM ALARM DOOR LOCK DOOR UNLOCK PRIORITY UNLOCK TRUNK/HATCH RELEASE POWER LIFTGATE POWER SLIDING DOOR (L) POWER SLIDING DOOR (R) SECURE TAKEOVER DOOR STATUS TRUNK STATUS HOOD STATUS E-BRAKE STATUS TACH OUTPUT BRAKE STATUS GLOW PLUG STATUS PARKING LIGHTS HAZARD LIGHTS A/M CONTROL CM-900 FTI-CDP1 - DL-CH12 - Type 5 2014-18 Jeep Cherokee PTS BLADE PWR pink/black C B *Not required green pink B A 3 2 4 1 OBD-II connector 1 1 16 PTS Button 2 ENGINE START STOP Headlight switch 3 AUTO RAP SHUTDOWN *Not required D Trailer Pack Connector (left of steering column) 4 7 23456 1 13 12 11 10 9 8 pink LED Programming Error Codes Module LED flashing RED during programming 1x - CAN Error 2x - Key code not learned 3x - No IGNITION 4x - No immobilizer, check CAN/key 5x - VIN error, check CAN wiring 6x - See 4x error 7x - KLON error 8x - No IGNITION, check connection INSTALL GUIDE ALL IN ONE CHRYSLER/FIAT/JEEP Patent No. US 8,856,780 CA 2759622 Page 40 of 43 COM-BLADE-AL(DL)-CH12-EN Doc. No.: ##72849## 20201120 MODULE PROGRAMMING PROCEDURE - PTS NOTE I IMPORTANT: The hood must be closed. 1 Close driver door. Re-open driver door to wake up data bus. 2 Press UNLOCK on OEM remote. (If the vehicle is not equipped with an OEM remote, press on the module programming button.) 3 Wait, LED will flash BLUE once [1x]. If LED does not flash GREEN, repeat step 2. 10 OFF ACC ON START ENGINE START STOP Set ignition to OFF position. 11 WARNING: Disconnect power last. Disconnect module from vehicle. 12 Connect module to computer and proceed with extended programming. 4 OFF ACC ON START Set ignition to ON position. ENGINE START STOP 13 WARNING: Do not press module programming button. Connect power first. Connect module to vehicle. 5 6 OFF ACC ON START Wait, if LED turns solid RED proceed to step 6. If LED flashes BLUE rapidly, proceed to step 10. Set ignition to OFF position. ENGINE START STOP 14 OFF ACC ON START Set ignition to ON position. ENGINE START STOP 15 Wait, LED will turn solid BLUE for 2 seconds. 7 Repeat steps 4 to 6, eight times [8x]. 8 OFF ACC ON START Set ignition to ON position. ENGINE START STOP 16 OFF ACC ON START ENGINE START STOP Set ignition to OFF position. 17 Module Programming Procedure completed. 9 Wait, LED will flash BLUE rapidly. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020 INSTALL GUIDE ALL IN ONE CHRYSLER/FIAT/JEEP Page 43 of 43 Patent No. US 8,856,780 CA 2759622 COM-BLADE-AL(DL)-CH12-EN Doc. No.: ##72849## 20201120 WARNING: READ BEFORE RNEOMTOICTEE STARTING THE VEHICLE IMPORTANT I All vehicle doors must be closed and locked prior to remote start sequence. Failure to comply will result in remote starter malfunction. TAKE OVER PROCEDURE - PTS - TO THE VEHICLE OWNER NOTE 2 I All vehicle doors must be closed and locked prior to remote start sequence. TIME RESTRICTI N COMING UP ! TIME RESTRICTI N Within 45 SECONDSfrom previous step: Open vehicle door. Enter vehicle. Close vehicle door. Press and release BRAKE pedal. 1 Unlock vehicle door using OEM or after-market remote, or door request switch. 3 Take over procedure completed. ! Failure to follow procedure will result in vehicle engine shutdown. WWW.IDATALINK.COM Automotive Data Solutions Inc. © 2020Adobe PDF library 17.00 Adobe Illustrator(R) 24.0