SECRUI Wireless Doorbell

Installation

Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to see and hear.

For Receiver:

Plug-in receiver: Just plug the receiver into a standard outlet in the room.

For Push Button:

IMPORTANT: Before installation, please test if the operating range you choose is working and set music if needed.

Before you drill any hole in the wall, please make sure there are not cables or pipes.

To install, you will require a drill and cross-headed screwdriver.

Content:

• Doorbell
• Push Button
• Adhesive Sticker
• Screws & Anchors
• User Manual

Content will vary according to your kit.

The push button supplied with this kit is pre-programmed to operate with the doorbell. If it is not, see "Connect a Push Button" on page 5.

Safety:

Before proceeding with the installation, please note the following safety warnings:

• Always follow the manufacturer's advice when using power tools and wear suitable protective equipment (e.g., safety goggles) when drilling holes, etc.
• Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt.

What You Should Know Before Installation:

1. Test the operating range you desire. Choose an electric outlet at the height of 3.3 feet at least and plug in the receiver and take the button outside the door to test if it can work well within the range you have chosen.
2. Set a desired music (different or same one) for transmitters before installation. For music setting, see Operating Instructions. Doorbells have been paired and set to a default chime (Ding Dong) before leaving the factory.
3. Please do not install the transmitter on metal doors since it is hard for the signal to transmit.
4. Please take out the battery insulating strip before using. (As picture 1) [battery-insulation-strip-removed]
5. Ensure all surfaces are clean by wiping the installation area with a clean cloth. Please note that the sticker will have poor adhesion if you attach it to a dirty or uneven surface. Sunlight or rain will also affect the adhesion over a longer period of time.

Product Structure Diagram

AC Powered Receiver

• ① Music Control [music-control-icon]
• ② Volume Control [volume-control-icon]
• ③ Plug [plug-icon]
• ④ LED light [led-icon]
• ⑤ Speaker [speaker-icon]

Waterproof Transmitter

[Image of transmitter with labels for button and battery compartment]

Set Up and Operation

1. Adjust the Volume

Press the [volume-up-button] 1s. (when the power is cut off, and power is restored again, the volume will be automatically adjusted to maximum)

2. Change the Tune

Press the [loop-tones-button] 1s: Loops tones in sequence and plays the current tone.

Long press 5s [change-direction-button]: Changes tone loop direction.

3. Connect a Push Button

You can connect up to 20 accessories to your doorbell, including other push buttons, window or door opening sensors, and motion sensors.

(1) VARIABLE - Tone Pairing:

1. Plug-in the receiver, pressing and holding the [pairing-button] on the receiver for 5s, the receiver beeps once, which means the receiver gets into pairing mode.
2. Press the push button, the receiver will beep twice with LED indicator flashes 1s. [paired-indicator]
3. Press push button again, the receiver will beep once with LED indicator flashes 1s, which means the pairing is successful. [pairing-successful-indicator]
4. Short press [exit-pairing-button] or leave it 20s without any operation, the doorbell will exit the pairing mode.

Adding additional push buttons or receivers, please follow the above steps.

(2) FIXED - Tone Pairing (only play your saved tone):

1. Select a tone that you like.
2. Pressing and holding the [select-tone-button] & [music-button] for about 5s until the receiver beeps once, which means the receiver gets into pairing mode.
3. Press push button once, the receiver will beep twice with LED indicator flashes 1s. [paired-indicator]
4. Press push button once again, the receiver will beep once with LED indicator flashes 1s, which means the pairing is successful. [pairing-successful-indicator]
5. Short press [exit-pairing-button] or leave it 20s without any operation, the doorbell will exit the pairing mode.

Adding additional buttons/receivers, please according to the above steps.

Note: Pair and set only one transmitter at a time to avoid interference and ensure successful operation.

4. Reset (Clearing out Settings)

Hold down the [reset-button] and plug it into an outlet. After playing the beep 10 times, all settings will return to factory defaults.

Chimes List

Battery Replacement of Push Button

Open the battery cover and install the CR2032 battery.

[Image showing battery replacement]

Mounting the Transmitter

① Open the Transmitter with a screwdriver and separate the front cover from the back cover. Penetrate the two standby holes at the back cover with two screws. Then fix the screws on the wall at suitable height.

[Image showing screw mounting]

② Or you can stick the Transmitter with the double-sided adhesive tape.

[Image showing adhesive mounting]

If you are not mounting the push button to the wall, place it where you want it.

Specifications

Troubleshooting

1 Year Limited Warranty

This product is warranted to the original purchaser only for a period of 1 year from the date of purchase for products damaged due to defect in workmanship and materials. Proof of purchase is required to obtain warranty service. Warranty is for replacement only. No service parts are available for these products. No other warranties are expressed or implied. Batteries are not covered under this warranty.

For warranty service, please contact SECRUI Customer Service by email: contact@secrui.com

IMPORTANT: PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE WHEN REPLACING BATTERIES