User Manual for Meteer models including: HD-M1, 2BKMR-HD-M1, 2BKMRHDM1, HD-M1 Trendy Desktop Robot, HD-M1, Trendy Desktop Robot, Desktop Robot, Robot
Shenzhen Yingfengfan Technology Co., Ltd HD-M1 2BKMR-HD-M1 2BKMRHDM1 hd m1
Meteer Robot 1. In th e B o x MeteerUser ManualUSB-C Cable 2. In ro d u ctio n Meteer Trendy desktop robotThe perfect fusion of technology and fun Meteer Trendy Desktop Robot: Perfect Fusion of Technology & Fun MeteerTrendy desktop robotBuilt in AI chip and cutting-edge technologyThe exterior design is unique, with a flexible and agile body, exquisite lines, cool colors, and dynamic eye expressions. Whether placed on an office desk or a bedside table in the bedroom, it can instantly become the focus, adding a sense of futurism and technology to the entire space MeteerTrendy desktop robots cheer you on with music, dance, and powerful brains! Meteer is also a great life assistant with voice interaction capabilities that can understand your questions and provide accurate answers. Whether it's searching for information, writing content, or chatting to relieve boredom, it can handle it with ease. Can become a companion during work and study, adding fun to dull times Meteer's design inspiration comes from handmade culture, with a unique and personalized appearance that showcases a vibrant and creative artistic fashion sense 3. G et to ko n w Illustration (Status Light) (MIC) (sunglasses) (trumpet) (Servo) (13-inch TFT display) (Reset button) (TF card) 4. F irst u se 4.1 Pow er on Press and hold the power button for 2.5 seconds to turn on the device, and it will default to dialogue mode 4.2 Distribution network Voice prompt "Enter network configuration status, please use the APP to configure the network" Install the "Meteer" app from the App Store or Google Play Open the Meteer app and click on "WiFi Distribution Network" Turn on Meteer and connect to 2.4G band WiFi (does not support 5G) Click on 'Meteer' Click on 'Connect' Enter the WiFi password and click on 'Connect to WiFi' Successful distribution network" " Voice prompt "Network connection successful" 4.3 interaction Touching your head, or saying 'Hi Meteer' Start voice conversation, touch again, end conversation 5. F u n ctio n s Illustration 0 Dialogue mode (default) 1 music and dance 2 Comes with music mode 3 Voice changing mode 4 Choreography mode 5 Swing mode 6 OTA mode 7 Set mode 5.1 Dialogue m ode *Default mode, please refer to the first use for details on distribution network and interactive operation. *In dialogue mode: When there is no operation, play idle animation every minute, and then play sleep animation five times. Press any key to wake up. 5.2 Dance m ode Enter dance mode Touch your head, play random songs and dance accompaniment Touch your head again and switch to playing a random song 5.3 Voice changing m ode Enter voice changing mode Press the left and right keys to select item touch one's headRecording "Hi Meteer" Repeating "Hi Meteer" 5.4 Choreography m ode Enter choreography mode Swing the joints and make a movement Right click to record and edit the next action (up to 100 actions) Left click to switch emoticons and play the current editing action Touch your head and repeat playing all the actions currently programmed 5.5 Sw ing m ode Enter swing mode Touch your head and switch expressions Swing the joints and perform movements 5.6 OTA m ode Enter OTA mode Automatically search for new firmware Search completed If there is new firmware, automatically confirm the upgrade If there is no new firmware, play the prompt and return to the previous level Upgrade completed, automatically shut down, run new firmware on next boot 5.7 set up Enter setup mode Press the left and right keys to switch between items; Touch your head and select an item Press the left and right keys to adjust the parameters Atmosphere light color Volume Setting WiFi connection (see First Use - Distribution Network for details) battery level Version information number Touch your head, confirm the settings, and return to the previous page 6. A tten tio n s 6.1 Charge Illustration New content added The optimal charging time is 70 minutes Low battery state, charging state, fully charged state You can check the Meter battery level through 'Settings' Dance at maximum volume for 90 minutes in Bluetooth mode when fully charged 6.2 Reset New content added If an abnormality occurs during the operation and the power cannot be turned off, a reset can be performed by forcibly powering off and then powering on again Step1 Insert the card needle into the back of the head Step2 Meteer Shut down Step3 Restart for use 6.3 FQA 6.3.1 Abnorm al card m achine If there is an abnormal stuck machine, please check if there are any unfinished or improper operations in the current process that prevent it from entering the next step If the operation is correct, try pressing the power button to return to the homepage If unable to return to the homepage, try shutting down and restartingUnable to shut down, try resetting with a pin 6.3.2 Unable to distribute netw ork If Bluetooth devices cannot be found, please confirm that your phone's Bluetooth is turned on If the network connection fails, please confirm that the WLAN connected to the phone is 2.4G (does not support 5G) If it's 2.4G, try changing the network to a mobile hotspot 6.3.3 Firm w are upgrade failed If there is a delay in the firmware upgrade progress bar, it may be due to unstable network. Please try using a mobile hotspot to reconfigure the network and update it again If the exit mode fails, try forcing a shutdown and retry 6.4 Product specifications name Meteer Robot horn 42W*2 PCS size high Displ 1.3" 230.6mm ay wide 154mm 240*240 TFT* 2pcs thick 117.5mm bare 590g weight Batter y capac ity 2500mA h Numb er of servos 11pcs charg 5V-2A / e 9V-2A 6.5 Safety Tips How to save and use the product? If not washed with water, not exposed to direct sunlight, and not close to sources of fire... 6.6 w arranty policy How many days of warranty policy is provided? For example, 90 days What is the specific warranty service? For example, during the warranty period, provide official purchase receipts to repair or replace faulty product components... Under what circumstances is warranty service not provided? For example, improper testing... 6.7 Com pliance Statem ent What certificates have been applied for? For example, FC, WEEE, CE... This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.WPS 文字