Haier High Wall Duct-Free System

Introduction

Thank you for purchasing this Haier product. This manual will help you get the best performance from your new heat pump.

For future reference, record the model and serial number located on the label on the side of your heat pump, and the date of purchase.

To register your new Haier Duct Free System, visit haierductless.com/product-registration and input the model/serial number information. Registration is required within 60 days of installation to receive a 10-year compressor and parts warranty.

Important Safety Information

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock, or personal injury.

• Use this appliance only for its intended purpose as described in this Owner's Manual.
• This heat pump must be properly installed in accordance with the Installation Instructions before it is used.
• Turn the unit OFF and unplug your heat pump before cleaning the air filter.
• GE Appliances does not support any servicing of the heat pump. We strongly recommend that you do not attempt to service the heat pump yourself.
• Do not store or use combustible materials, gasoline, or other flammable vapors or liquids in the vicinity of this or any other appliance. If disposing of a product with refrigerants, check with the handling company about proper disposal.
• These R410A heat pump systems require contractors and technicians to use tools, equipment, and safety standards approved for this refrigerant. DO NOT use equipment certified only for R22 refrigerant.

Keep batteries away from children.

• This remote control contains batteries. If a new or used battery is swallowed or enters the body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep it away from children.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
• Cells shall be disposed of properly, including keeping them away from children.
• Even used cells may cause injury.

This product is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Children should be supervised to ensure that they do not play with the product.
• Any damage to the electrical supply must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.

READ AND SAVE THESE INSTRUCTIONS

Remote Control Features and Settings

The remote control allows you to operate the Haier High Wall Duct-Free System. Below are descriptions of the buttons and their functions.

Remote Control Layout

The remote control features numerous buttons for various functions. The main buttons are numbered for reference:

• 1. POWER [Power Icon]: Press to start or stop the unit.
• 2. HEAT Button: Activates heating mode. In HEAT mode, warm air is blown after a short delay to prevent cold air. If FAN is set to AUTO, the fan speed adjusts automatically based on room temperature. The [Heat Mode Icon] will be displayed.
• 3. COOL Button: Activates cooling mode. In COOL mode, cool air is blown. If FAN is set to AUTO, the fan speed adjusts automatically based on room temperature. The [Cool Mode Icon] will be displayed.
• 4. DRY Button: Used for dehumidification. In DRY mode, if the room temperature drops 2°F below the set temperature, the unit operates intermittently at LOW speed, regardless of FAN setting. A crossed-out water droplet icon [Water Droplet Icon with Cross] is displayed.
• 5. SPEED Button: Cycles through fan speeds: LOW, MID, HI, AUTO. The fan icon [Fan Icon] is displayed. Holding the SPEED button for 10 seconds enters FAN mode. Pressing any other button exits this function.
• 6. TURBO Button: Speeds up airflow to the highest setting in heating and cooling modes. The "TURBO" icon is displayed. Pressing TURBO again or the SPEED button exits this function.
• 7. QUIET Button: Sets the fan to the lowest speed. The "QUIET" icon is displayed. Pressing QUIET again or the SPEED button exits this function.
• 8. TEMP +/- Buttons:
  • TEMP +: Increases the set temperature by 1°F (0.5°C).
  • TEMP -: Decreases the set temperature by 1°F (0.5°C).
  The operating temperature range is 60°F-86°F (16°C-30°C).
• 9. MOTION SENSOR Button: Activates Motion Sense mode, displaying "Eco". If no motion is detected for 20 minutes, the unit enters Eco mode, adjusting temperature by 1°F (0.5°C) every 10 minutes (decreasing in heat mode until 68°F/20°C, increasing in cool mode until 78°F/26°C). Total adjustment is capped at 4°F (2°C). Motion detection exits Eco mode immediately. This function may not adjust temperature further if the set point is already at the limit.
• 10. SWING UP/DOWN Button: Controls the horizontal airflow louvers.
  • Airflow Status Display (COOL/DRY): Shows various upward and downward louver positions.
  • Airflow Status Display (HEAT): Shows various upward and downward louver positions.

  Note: Avoid keeping the horizontal louver in the downward position for extended periods in COOL or DRY mode to prevent condensate formation. The unit returns to the previous setting upon power-on and fully opens before closing upon power-off.

• 11. SWING SIDE/SIDE Button (select models): Controls the vertical airflow louvers.
  • Airflow Status Display (COOL/DRY/HEAT/FAN): Shows various left and right louver positions.

  Note: High humidity may cause condensation if vertical louvers are angled too far left or right. The unit returns to the previous setting upon power-on.

• 12. DISPLAY Button: Toggles the indoor display on/off. Pressing 10 times within 5 seconds displays ambient temperature (2 beeps). Pressing again 10 times within 5 seconds displays set temperature (4 beeps). Default display is set temperature.
• 13. SLEEP Button: Activates the sleep function. The display light turns off after 20 seconds.
  • COOL or DRY modes: Temperature increases 1°F (0.5°C) after 1 hour, another 1°F (0.5°C) after 2 hours, and decreases 1°F (0.5°C) after 7 hours. Returns to original setpoint at the 8th hour. This optimizes comfort and efficiency during sleep.
  • HEAT Mode: Temperature decreases 2°F after 1 hour, another 2°F after 2 hours, increases 1°F after 5 hours, and returns to original setpoint after 8 hours.
  • AUTO Mode: The unit operates in a corresponding sleep mode adapted to the automatically selected operation mode.

  Note: In Sleep mode, fan speed is set to low and cannot be changed. If TIMER is set, Sleep cannot be set, and vice versa.

• 14. FOLLOW Button: The airflow follows the person.

  Model	Detect Area	Louver Up/Down	Louver Left/Right
  FOLLOW	Detect person in single zone	Remote setting position	Swing in the direction of the person
  	Detect person in multi zones	Remote setting position	Swing automatically
  	Detect nobody	Keep the initial setting position	Keep the initial settings position

• 15. SURROUND Button: The airflow surrounds the body.

  Model	Detect Area	Louver Up/Down	Louver Left/Right
  SURROUND	Detect person in single zone	Remote setting position	"Health airflow (up) in cooling mode" / "Health airflow (down) in heating mode"
  	Detect person in multi zones	Keep the initial setting position	Swing automatically
  	Detect nobody	Keep the initial setting position	Keep the initial settings position

• 16. AUTO Button: The heat pump automatically selects Cool, Heat, or Fan operation based on the set temperature. When FAN is AUTO, fan speed adjusts automatically.
• 17. VACATION Button: Sets heating to maintain 10°C/50°F to prevent freezing during long unoccupied periods.
• 18. TIMER ON/OFF Button: Sets the timer. Use CLOCK UP/DOWN to adjust time by 1-minute increments. Press APPLY to confirm. Press TIME OFF to cancel.
• 19. CLOCK Button: Sets the clock. Use CLOCK UP/DOWN to adjust time by 1-minute increments. Press APPLY to confirm. The clock retains the original time if APPLY is not pressed within 10 seconds.
• 20. APPLY Button: Saves and cancels TIMER and CLOCK selections.
• 21. F/C Button: Switches the remote and unit display temperature between Fahrenheit and Celsius.

Manual Operation and Maintenance

Manual Operation

Use the POWER button only when the remote control is lost or damaged.

• Pressing the POWER button will cause the unit to beep once, indicating operation has started.
• The unit will run automatically in the following modes:

  Room Temperature	Designated Temperature	Timer Mode	Fan Speed	Operation Mode
  Above 73°F	79°F	No	AUTO	COOL
  Below 73°F	73°F	No	AUTO	HEAT

  [Emergency Operation Switch Icon]

• In Manual Operation, temperature and fan speed cannot be changed, and TIMER or DRY modes are not available.

Inserting the Batteries

1. Remove the battery cover.
2. Insert 2 AAA batteries, noting polarity.
3. Reinstall the battery cover.

Note:

• Remote control range is less than 23 feet (7 meters) without obstructions.
• A weak display or reduced range may indicate the need for battery replacement.
• Remote control malfunctions can sometimes be corrected by removing and reinstalling batteries.
• Remove batteries if the unit will be unused for an extended period. If any display segments remain active after battery removal, press the RESET button.

Optimizing Performance

1. Close doors and windows during operation.
2. Do not block air inlets or outlets.
3. Wipe the cabinet with a soft, dry cloth. For stubborn stains, use a neutral detergent diluted with water. Wring out the cloth before wiping, then wipe off detergent residue.

Cleaning the Front Cover

1. Open the front cover by pulling it upward.
2. Remove the filter: Gently push up on the center tab until it releases, then pull the filter down.
3. Clean the filter: Use a vacuum cleaner or wash with water. Dry completely after washing.
4. Attach the filter: Ensure the "FRONT" label faces outward. Secure it behind the holding tabs. Incorrect attachment may reduce efficiency.
5. Close the front cover.

Troubleshooting Tips

For additional troubleshooting tips, consult the full owner's manual at GEAppliances.com.

Limited Warranty

For detailed warranty information, please refer to the installation manual.

Important Notices

IMPORTANT

Do Not Return This Product To The Store

If you have a problem with this product, please call 1-877-337-3639 for the name and telephone number of the nearest authorized service center. DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE.

IMPORTANT

Ne pas Réexpédier ce Produit au Magasin

En cas de problème avec ce produit, veuillez composer le 1-877-337-3639 pour connaître le nom et le numéro de téléphone du centre de service autorisé le plus proche. PREUVE D'ACHAT DATÉE, NUMÉRO DE MODÈLE ET LE NUMÉRO DE SÉRIE REQUIS POUR LE SERVICE DE GARANTIE.

IMPORTANTE

No regrese este producto a la tienda

Si tiene un problema con este producto, por favor comuníquese al 1-877-337-3639 para solicitar el nombre y número telefónico del centro de servicio al cliente autorizado más cercano. NECESITA UNA PRUEBA DE COMPRA FECHADA, NÚMERO DE MODELO Y DE SERIE PARA EL SERVICIO DE LA GARANTÍA.