Pro-Ject T2 W Built in Wi-Fi Turntable Instructions

Instructions for Pro-Ject models including: T2 W Built in Wi-Fi Turntable, T2 W, Built in Wi-Fi Turntable, Wi-Fi Turntable, Turntable

252T2WHGB

252T2WHGB, Pro-Ject T2W HG BLack turntable w.streaming, WWW.CRUTCHFIELD.COM

HNEWBERRY

Pro-Ject T2 W owner's manual

Pro-Ject T2 W (Walnut) Manual belt-drive turntable with built-in phono preamp, pre-mounted cartridge, and Wi-Fi streaming at Crutchfield

File Info : application/pdf, 23 Pages, 10.02MB

JavaScript is disabled. Open the PDF or Download.

252T2WHGB

~ro-Ject
AUDIO SYSTEMS
INSTRUCTIONS FOR USE
Pro-Ject T2 W

Dear Music Lover,
Congratulations and thank you for choosing Pro-Ject Audio Systems record player.
Your T2 W turntable has been handcrafted and rigorously tested by skilled technicians to give you years of enjoyable, trouble-free service. Please contact your dealer if you require additional assistance.
Important: Your turntable was shipped partially disassembled in order to avoid damage to sensitive parts. Please check immediately to make sure that neither the packaging nor the device was damaged in transit. If you are missing parts or if the unit is damaged, please do not operate and contact your dealer.

Contents

Product illustrations

Setup

1. Platter and drive belt installation

2. Cartridge installation, stylus exchange

3. Vertical Tracking Force setting (VTF)

4. Maintenance and cleaning

5. Switching ON and OFF, changing replay speed

6. Anti-skating

7. Connection to the amplifier

Technical parameters

Troubleshooting, warranty, service

Exploded view of the packaging

Please do your part to help protect the environment: Disposal of packaging material: Pro-Ject packaging is carefully designed to protect your component from damage in transit and you are strongly urged to keep the original packaging in order to safely ship or otherwise transport your turntable in the future.
However, the packaging materials were chosen to be environmentally friendly, so if you must discard the packaging, please recycle.

GENERAL INFORMATION

Controls, features and connections

PLATTER & FELT MAT

CHASSIS

SPEED CONTROL BUTTON

MOTOR WITH PULLEY

DRIVE BELT

SUB-PLATTER

TONEARM COUNTERWEIGHT

ANTI-SKATING ADJUSTMENT SCREW WITH SCALE

TONEARM REST / REMOVABLE TRANSPORT LOCK

10 TONEARM LIFT LEVER

11 TONEARM TUBE

12 HEADSHELL WITH FINGER LIFT AND PRE-MOUNTED CARTRIDGE

13 LID

14 LID HINGES

15 HINGE FASTENERS

16 POWER SUPPLY SOCKET

17 LINE RCA OUT, ETHERNET, Wi-Fi RESET SWITCH, Wi-Fi ON/OFF BUTTON, Wi-Fi STATUS LED

Accessories

SINGLE ADAPTOR

ALLEN KEY 1,5mm

COUNTERWEIGHT no. 105 (FOR CARTRIDGE WEIGHT 5 11.5g)

TWO-POINT CARTRIDGE ALIGNMENT PROTRACTOR

CONNECTION CABLE (CONNECT IT E RCA)

SETUP GUIDE

UNIVERSAL POWER SUPPLY

3 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

14
15 17

14
15 16

SETUP
1. Platter and drive belt installation Please remove drive belt from accessories box and install it as shown in the following illustration. Put the felt mat on the top of the platter.
FELT MAT
MAIN PLATTER
DRIVE BELT
SUB-PLATTER

2. Cartridge installation, stylus exchange
* If you purchased this turntable in a package that included the cartridge, this has already been done for you. Install the cartridge into the aluminium headshell, using the appropriate hardware included with your cartridge. All cartridges with half inch mounting holes can be fitted.

Connect the cartridge as indicated below:

· White · Red · Green · Blue

left channel L+ right channel R+ right channel Rleft channel L-

For correct cartridge alignment, use the two-point cartridge alignment protractor provided with your T1 accessories. If unfamiliar with two-point setup, please refer to your dealer.

A damaged or worn stylus may harm your record collection and should be replaced. Please remove stylus protection before pulling the stylus from the cartridge and replace for a new one. Stylus type is exchange for pre-mounted cartridge Sumiko Rainier: Stylus Sumiko Rainier. If in doubt, consult your local dealer or distributor.

5 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

3. Vertical Tracking Force setting (VTF)
The T2 W comes with the counterweight already assembled on the tonearm, and the tracking force is factory pre-adjusted.
To adjust or fine tune the tracking force manually, loosen the hexagonal screw on top of the counterweight (6) using the allen key provided. Remove the stylus protection cover and place the stylus pressure gauge onto the platter. To set the required VTF, lower the tonearm lift lever (10) as indicated in the illustration and place the tip of the stylus on one of the points on the scale. For example, the Sumiko Rainier requires 20mN of tracking force, so place the stylus on the 20mN point. If the stylus gauge becomes level when the tonearm is lowered down onto the desired point, then the correct pressure has been achieved. However, if there is insufficient or excessive pressure, the gauge will either not move or tilt down.

STYLUS PRESSURE GAUGE
To adjust the amount of pressure, carefully move the counterweight (11) along the support rod, until the stylus pressure is sufficient to raise the pressure gauge to the level position. Moving the counterweight (6) away from the cartridge will reduce pressure and towards will increase pressure. Finally secure the counterweight (6) using hexagonal key provided.

VTF+ ~

VTF-

4. Maintenance and cleaning
Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts. It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.
If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching.

5. Switching on and off, changing replay speed
The turntable is equipped with a three-position switch for ON/OFF and electronic speed change. To play records at 33 rpm. press this switch (3) to the rear side. To play records at 45 rpm. press this switch (3) to the front side as shown on illustration below.

33 rpm

45 rpm

6. Anti-skating The anti-skating force is pre-adjusted from the factory corresponding to the tracking force. Sumiko Rainier recommended tracking force 20mN = anti-skating set to 2 (middle position). You can adjust the anti-skating by rotating the anti-skating setting screw to the left or right.

Anti-skating setting screw
7. Connection to the amplifier The record player has gold plated female RCA phono sockets with LINE output (the internal phono preamp of the T2W is always on). Connect the RCA outputs of your T2 W to a line input (such as AUX, CD, Tuner, Tape or Video) on your amplifier. Take care to connect the left and right channels correctly. The right channel is usually marked red, the left channel black or white. The earthing wire of the tonearm lead should be connected to the earth terminal on your amplifier (if provided).
The analogue RCA output remains purely analogue and is not digitized, not affected by any additional delay or in any other way influenced by the Wi-Fi capabilities of the turntable. You can rest assured that the analogue output will always give you the pure analogue output signal.
7 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

RCA Line Output

Stream Control Button

Wi-Fi Control LED

Wi-Fi Reset Button Ethernet Socket

8. Wi-Fi
App Control: Please download the App "Pro-Ject Control" (Android and iOS) to control the Wi-Fi functionalities of your T2 W.
Browser Control: You can enter die IP address of your T2 W into any webbrowser on a device connected to the same network and control the Wi-Fi functionalities of your T2 W in exactly the same way as with the App.
You can use IP Scanners or get the IP address from the "Pro-Ject Control" App. Alternatively, the Pro-Ject Control App will show you the IP address of your turntable as well, after you connected it to your network via ethernet or Wi-Fi.

Wi-Fi Startup

The Wi-Fi module of your T2 W will boot up as soon as you connect the power supply to your turntable. You can see its status from the colour of the LED:

Red static: Wi-Fi module starting up Red blinking: Module started up, no ethernet or Wi-Fi connection established Green static: Connected to ethernet or Wi-Fi network Blue static: Streaming audio Blue blinking: Previous streaming receiver unavailable

Network Connection

Ethernet: Connect an ethernet cable, the network connection will be automatically established and LED turns green. Ethernet is recommended for lossless streaming (note that also your streaming receiver should be connected via ethernet and not Wi-Fi to avoid connectivity issues).

Wi-Fi: You can add the T2 W to your Wi-Fi network via our "Pro-Ject Control" App. Connect your T2 W to power and wait until Wi-Fi module has finished booting (Status LED). Then open the "Pro-Ject Control" App and you will see your turntable in the list of devices
waiting to be connected to a Wi-Fi network. If the turntable and the Wi-Fi Setup don't show up immediately, don't worry. It can take 10 seconds to scan for available devices. Press "Wi-Fi Setup" and follow
the next steps.

Wi-Fi setup is done via BLE (= Bluetooth Low Energy), so please make sure your phone is granting Bluetooth access to the "Pro-Ject Control" App. For BLE, you do not need to pair your phone to the turntable. BLE always, doesn't matter which BLE device, works WITHOUT pairing. A low energy Bluetooth connection can be established on the fly automatically, just by having Bluetooth turned on and access granted to the App. Please allow 10-15 seconds for your phone to discover the turntable after first starting the app, depending on how fast the Bluetooth connection is. If necessary, restart your phone after granting access.

Wi-Fi Control Button
Press for 2 seconds: Turns Wi-Fi on or off Short press: When turned on, start streaming to the previously selected streaming device
The Wi-Fi Control Button is a quick interface for you to start streaming to the streamer that you previously selected in the Pro-Ject Control App or T2 W webinterface. You can also turn off the Wi-Fi module should you wish to declutter your Wi-Fi network. Energy consumption is negligible in idle mode when the module is turned on. But it won't hurt to turn the module off, if you don't use your turntable for longer periods to save energy consumption.
In usual operation you will probably not need this button, as you will choose which device to stream to in your App or webinterface. But once you have chosen an output streamer once, you can comfortably start streaming to it again in a later session, by just pressing the button once. This saves time and there is no need to break out the App or webinterface.

Pro-Ject Control App & Webinterface With the Pro-Ject Control App or the T2 W's webinterface you'll do most of your interaction with the T2 W.

10:46
·~ =-ro-Ject <D

f: ro-Ject

Pro-Ject-56a429

Rs stream box s2 ultra
[t) Stream Box RS

Rs stream box s2 ultra
[e) Stream Box RS

r 1 1 Stream Box 52 OS room

r 1 1 Technical Department
SHOP - Sones Five Med1a Renderer Den - So nos Play: S Media Renderer
Shop stream box s2 ultra
Samsung The Frame 55

rI I Technical Department
SHOP - Sones Five Media Renderer Den - Sanos Play: 5 Media Renderer
Shop stream box s2 ultra
Samsung The Frame 55

After connecting the T2 W to your network, choose which device to control (should you have more than one on your network) from the main screen and from there choose which output device you want stream your turntable to. You can stream to as many output devices as your network connection can handle. To stop the stream simply select the output device again, the blue outline will go away, and streaming to that device will stop.
Allow some time after choosing an output device and sending the stream to them. Each device reacts differently past and reports the status back. Some are almost instantaneous and some take a few seconds. The T2 W uses UPNP to hand over the digital audio streams and the streams itself are either MP3 or FLAC, and implementations can vary from manufacturer to manufacturer.

9 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

The more output devices you stream to, the more network bandwidth you need. The T2 W has very powerful Wi-Fi and ethernet and internal processing power and can in theory handle hundreds of lossless audio streams at the same time. The bottleneck is most likely your Wi-Fi access point or Wi-Fi pollution (too many different Wi-Fi networks in too close proximity to each other.

Options Menu

The wheel in the top left corner takes you to the options menu.

Automatically starts streaming to the last selected output device as soon as the motor of the T2 W is turned ON.
Enter Wi-Fi connection data or configure Ethernet
Displays network information
Check back here regularly for Firmware Updates
Settings for language, power management and factory reset
Advanced streaming settings
Streaming Compatibility The standard audio stream is designed to be compatible with as many devices as possible. Requirements are that your streamer is UPNP capable and can play MP3 encoded live-streams. An up-to-date list of compatible manufacturers and devices can be found on the T2 W product page on our Pro-Ject Audio Systems website. Lossless Audio Stream The lossless audio stream in the Advanced Settings is not intended to be compatible with as many devices as possible, but is intended to be used with high-end streamers like our own Stream Box S2 Ultra in excellent network conditions. Please make sure to use this setting only on really good W-Fi connections or with ethernet cables, as lossless requires roughly 6x more bandwidth. At Pro-Ject Audio Systems the Stream Box S2 Ultra and Stream Box S2 are compatible with the lossless stream. A list of lossless compatible devices/manufacturers can be found on the T2 W product page on our Pro-Ject Audio Systems website. If the lossless audio stream is turned on, only selected compatible devices will receive it, the rest will continue to receive the standard compressed stream, so you won't run into any major bugs or issues.
10 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

Secondary Stream The secondary stream in the Advanced Settings is a nice helper, in case your streaming device is not UPNP capable. Many streamers allow adding custom radio stations. If you start the secondary stream and copy the stream-link into your webbrowser or add a custom radio station, you'll get to enjoy your T2 W on many more devices.
The secondary stream is only available as MP3. Airplay While the T2 W is not able to play to Airplay devices directly, you can build a workaround with the secondary stream.
Long press on the stream link -> Open Link -> Press Airplay symbol -> Choose which device to play to Network Standby By default, your T2 W is configured to enter network standby after 20 minutes of inactivity. You can disable this functionality at your choice under Device Settings -> Power Management -> Auto Standby Mode.
If the T2 W is greyed out like here, it means it is currently in Network Standby mode. You can wake it up with the power button. You can also manually set it to network standby mode using the power button on the home screen.
11 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

Technical specifications Pro-Ject T2 / Pro-Ject 9''

Nominal speeds Speed variance Wow and flutter Signal to noise Effective tonearm mass Effective tonearm length Overhang WLAN standards

33/45 r.p.m. 33: ±0.60% 45: ±0.50% 33: ±0.19% 45: ±0.17% -67dB 9.5g
9" (230mm) 22 mm IEEE 802.11a/b/g/n/ac/ax 2x2 MIMO; 2.4/5GHz

Power consumption

4.5W

Power input

15V/ 0.8 A DC, universal power supply

Dimensions (W x H x D)

457 x 134 x 335mm

Weight

5.5kg

Dimensions packaging (W x H x D) 542 x 300 x 412mm

Weight incl. packaging

8.5kg

Technical specifications MM-Cartridge Sumiko Rainier

Frequency range Channel separation Output voltage Recommended load impedance Compliance/stylus type Recommended tracking force Capacitance Weight

15-25.000Hz
25dB /1kHz
5mV 47kohms/amplifier connection MM-input 10×10-6cm/dyn @ 100Hz elliptical
20mN 100pF 200pF
6.5g

12 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

Potential incorrect use and fault conditions
Pro-Ject turntables are manufactured to the highest standards and undergo strict quality controls before leaving the factory. Faults that may possibly occur are not necessarily due to material or production faults but can sometimes be caused by incorrect use or unfortunate circumstances. Therefore, the following list of common fault symptoms is included.
The platter doesn't turn although the unit is switched on:
The unit is not connected to the mains power supply. No mains at the socket. Drive belt is not fitted or has slipped off.
No signal through one or other channel or both channels:
No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier. This could be due to a faulty plug, broken wire or solder joint or simply loose plug/socket connection. Correct input not selected at amplifier. Amplifier is not switched on. Amplifier or speakers are defective or muted. No connection to the loudspeakers.
Distorted or inconsistent sound from one or both channels:
Record player is connected to wrong input of amplifier. Needle or cantilever damaged. Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.

Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.

Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems Copyright © 2023. All rights reserved.

The information was correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development.

Mac®, Mac OS®, iOS, Airplay, Apple are trademarks of Apple Inc., registered in the U.S. and other countries. AndroidTM is a trademark of Google Inc.

13 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

Waste from Electrical and Electronic Equipment (WEEE): This directive mandates the collection and recycling of electronics and component materials in order to reduce the amount going to landfills. Outside North America, when the user decides to discard this product, it must be sent to a separate collection facility for recycling. Please contact your point of purchase for more details.
Federal Communication Commission (FCC) Interference Statement FCC Part 15: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna - Increase the separation between the equipment and receiver - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected - Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To maintain compliance with FCC´s RF exposure guidelines, this equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Use on the supplied antenna. Contains FCC ID: 2AJYB-S1955
Declaration of Conformity
We, SEV Litovel, s r.o. Palackého 1160/34 78401 Litovel Czech Republic (manufacturer)
and Pro-Ject Audio Systems a division of Audio Tuning GmbH
Margaretenstrasse 98
1050 Vienna,
Austria (distributor)
declare under our responsibility that the product is in conformity with the provisions of Directives: 2014/35/EU including amendments 2014/30/EU including amendments 2014/53/EU including amendments
The following harmonised standards were applied: Health: EN62479:2010 Safety: EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013, EN62368-1:2014/A11:2017, EN61558-1:2005/A1:2009, EN61558-2-16:2009/A1:2013 EMC: EN301489-1 V2.2.0: 2017-03, EN301489-17 V3.2.0:2017-03, EN55032:2015, EN55035:2017, EN61000-3-2:2014, EN61000-3-3:2013 Radio Spectrum: EN300328 V2.1.1 (2016-11)
Pro-Ject Audio Systems a division of Audio Tuning GmbH
1050 Vienna, Austria, Margaretenstrasse 98
info@project-audio.com
14 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

LID
TONEARM TRANSPORT LOCK SUB-PLATTER INSERT MAIN PLATTER

SETUP GUIDE ACCESSORIES
TONEARM SUPPORTS POWER SUPPLY

15 © Pro-Ject Audio Systems · Pro-Ject T2 W · Revision 14.07.2023

T2 W Setup Guide
Getting started: · Make sure to have enough space to unpack your turntable. · Always unpack and set up in a clean environment. · Please Do NOT throw away the packaging! If you need service or
want to return your product, please send it in the original packaging including all inserts. In case of damage due to alternative packaging your dealer cannot guarantee a full refund. · Full manual: www.project-audio.com/en/product/t2w

1 Unpack all items from the accessorie bag.

a) Single adapter

b) Drive belt

c) Connect it E cable

d) Gauge

e) Alignment tool

c) e)

2 Remove the dustcover.

4 Unpack the power supply unit.

5 Unpack glass-platter and felt mat from the bottom of the carton.

3 Remove the turntable from the box. 6 Remove the protective cloth.

7 Put the drive belt over the sub-platter. 8 Put the felt mat on the platter.

10 Remove cartridge cap.

11 Remove tonearm and counterweight protection inlays.

12 Remove the red tonearm security tape.

14 Connect to your stereo system. T2 W wireless setup on the back of this paper.

16 Select the playback speed.

17 Have fun with music!

Connect it E RCA cable to amplifier line input

Power Cable

33 RPM

45 RPM

T2 W Wi-Fi Quick Setup
Connect to your Wi-Fi and start streaming.
Visit www.project-audio.com/en/product/t2w for FAQ`s and full manual
1 Install Pro-Ject Control App from Apple
App Store or Google Play Store.

Settings

Stream Selection Screen/

Refresh Stream List

Device selection

home screen

2 WiFi Connection:
Check Red LED light blinking

Wi-Fi Sleep Mode/Wake Up

Initial Wi-Fi setup works via Bluetooth, please make sure Bluetooth is turned on on your phone and the Pro-Ject Control App has Bluetooth access. Open the App, wait a few seconds until the App has scanned for your T2 W and tap Wi-Fi Setup.

After Wi-Fi setup is complete, the Wi-Fi Control LED will light up green. You will now see the the T2 W in the home screen.

Start streaming records by choosing your network streaming device. Active streams are indicated with a blue outline. Stop streaming by tapping the device again and the blue outline dissapears. Stream to as many devices as you like.

Wi-Fi Control Button Press for 2 seconds: Turns Wi-Fi on or off Short press: When turned on, start streaming to the previously selected streaming device
Red static: Wi-Fi module starting up Red blinking: Module started up, no ethernet or Wi-Fi connection established
Green static: Connected to ethernet or Wi-Fi network Blue static: Streaming audio Blue blinking: Previous streaming receiver unavailable

Wi-Fi Control Button

Wi-Fi Control LED light

Ethernet Socket

Wi-Fi Reset Button (recessed)

Need help?
Feel free to contact us. We have experienced partners all over the world. Find your dealer here: www.project-audio.com/en/find-a-dealer/

Service Should you encounter a problem which you are not able to alleviate or identify despite the above information, please contact your dealer for further advice. Only when the problem cannot be resolved there should the unit be sent to the responsible distributor in your country. Warranty repairs will only be affected if the unit is returned correctly packaged. For this reason we recommend keeping the original packaging. Never return a record player without making sure that is it safely disassembled and correctly packaged in the original packaging according to the diagrams on the last page of this user guide. Please remove these parts and pack them separately: lid, counterweight, anti-skating weight and belt. Fit the cartridge protection cap and the transport lock for the tonearm tube, prior to carefully packaging the record player.
Warranty The manufacturer accepts no responsibility for damage caused by not adhering to these instructions for use and/or by transportation without the original packaging. Modification or change to any part of the product by unauthorized persons, release the manufacturer from any liability over and above the lawful rights of the customer.
Warranty: Terms and Conditions · A warranty is valid only for products purchased from an authorized Pro-Ject Audio Systems retailer or dealer. · This warranty offer is limited to the repair of the equipment (which could be a repair or replacement at our discretion, neither of which
affects your original warranty). · Neither transportation or any other costs, nor any risk for removal, transportation and installation of products is covered by this
warranty. · A warranty is only valid for the original owner. It is not transferable. · To validate your warranty, you will need to provide the original sales invoice or other proof of ownership and date of purchase. · Warranty must be claimed within two years of purchase from an authorized dealer. After this period of time, the warranty will expire. · The legal warranty obligation exists in addition to this warranty and is not limited by this warranty.

A Pro-Ject Audio Systems warranty relates to claims of defects in materials and/or workmanship at the time of purchase. It does not cover: · Deterioration of component parts, the nature of which is to become worn or depleted with use, such as batteries and headphone ear
pads, drive belts and cartridges. · Damages caused by incorrect installation, connection or packing. · Damages caused by any use other than the correct use described in the user manual, negligence, modifications, or use of parts that
are not made or authorized by Pro-Ject Audio Systems. · Damages caused by faulty or unsuitable ancillary equipment. · Damages caused by accidents, lightning, water, fire heat, war, public disturbances or any other cause beyond the reasonable control of
Pro-Ject Audio Systems and its appointed distributors. · Products where the serial number has been altered, deleted, removed or made illegible. · Repairs or modifications that have been executed by an unauthorized person.
Commercial Use Faults caused due to using domestic products in commercial environments or on commercial scales are not covered by warranty. This turntable is intended for domestic use only. Using them for business applications are done so at your own risk.
Pro-Ject Audio Systems is a Registered Trademark of H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems Copyright © 2023. All rights reserved.
The information, pictures and figures were correct at the time of going to press. The manufacturer reserves the right to make changes to the technical specification without prior notice as deemed necessary to uphold the ongoing process of technical development. Contains FCC ID: 2AJYB-S1955

SG027

PRODUCT INFORMATION

T2 W
Stream Vinyl Anywhere
MSRP 999 (incl. VAT)
· NEW Works with most UPNP network enabled streaming products (Smart TVs, home theater A/V receivers, streaming loudspeakers)
· NEW Latest Wi-Fi technology and standards, 2.4/5GHz with 2x2 MIMO, up to 866 mbps speed (= 346 concurrent 24/48 lossless audio streams)
· NEW Standard lossy and optional lossless stream - up to 24bit/48kHz (see our compatibility FAQ)
· NEW ,,Pro-Ject Control" App · NEW Multiroom capable · NEW High-quality dual-stage split-passive MM phono
preamp · NEW 9" highly precise one-piece aluminium tonearm · NEW Spring based anti-skating system · NEW Counterweight with nickel finish · NEW larger chassis for higher stability · NEW Preadjusted Sumiko Rainier (MSRP 175) · NEW 10mm, 1,7kg zero-resonance glass platter · Speed control with electronic speed switch · Acrylic dustcover with adjustable hinges · Semi-symmetrical phono cable with metal connectors · Available in high gloss Black, satin White and Walnut · Handmade in Europe

Walnut: Satin White: High-Gloss Black:
Speed: 33,45 RPM (electronic speed change) Principle: Belt drive Speed variance: 33: 0,6% 45: 0,5% Wow & Flutter: 33: 0,19% 45: 0,17% Platter: 10mm thick, 1,7kg heavy glass platter with felt mat Main bearing: Stainless steel/brass Signal to noise: 67dB Tonearm: 9" aluminium Effective arm length: 230 mm Overhang: 22.0 mm Effective tonearm mass: 9.5 g WLAN standards: IEEE 802.11a/b/g/n/ac/ax 2x2 MIMO; 2.4/5GHz Included accessories: dustcover, feltmat, singles adapter, power supply, phono RCA cable Power Supply: 15V / 800 mA DC, universal power supply Power consumption: 4,5 W / <2W in network stand-by Dimensions: 542 x 300 x 412mm (WxHxD) Weight: 5,5 kg net

PRO-JECT AUDIO SYSTEMS www.project-audio.com

Technical data and price changes reserved. Page 1/4

T2 W: A New Modern Marvel
The T2 W intelligently enhances our highly acclaimed T1 formula while introducing our innovative Wi-Fi streaming technology. This groundbreaking feature enables seamless streaming to a wide range of modern network-enabled audio devices, including HiFi streamers, network-enabled home theater A/V receivers, and contemporary streaming loudspeakers. Such versatility empowers you to effortlessly integrate the T2 W into any living space, taking modern lifestyle concepts to an entirely new level.
Brandnew Network Streaming
We have added the latest Wi-Fi technology into the package, including all the latest WLAN standards and 2x2 MIMO allowing for theoretical speeds which are faster than modern, typical internet connections. And with MIMO we get maximum signal stability and protection against package and data loss. All this is necessary, because with the T2 W you can either stream in our standard compressed format enabling maximum compatibility or in 24bit/48kHz lossless, for selected high-end streamers like our Stream Box S2 Ultra. All this is multiroom capable as well, meaning you could send hundreds of audio streams to as many receiving devices as you like, before the T2 W multi-core CPU or Wi-Fi bandwidth start to crackle down. The new ,,Pro-Ject Control" App offers a fast and intuitive user experience, while the Wi-Fi setup can be effortlessly accomplished through modern BLE functionality, simplifying the setup process.

PRODUCT INFORMATION
Widest compatibility, hundreds of concurrent streams, intuitive user experience

PRO-JECT AUDIO SYSTEMS www.project-audio.com

Technical data and price changes reserved. Page 2/4

PRODUCT INFORMATION

Highest Quality Materials

The elegantly crafted CNC-machined plinth has been expanded in size to enhance stability and is available in striking finishes such as High Gloss Black, Satin White, or Walnut. It boasts a construction free of plastic components and meticulous manufacturing that eliminates any hollow spaces within, effectively preventing unwanted vibrations within the chassis. Furthermore, the glass platter in the T2 W has been made heavier and thicker compared to its predecessor, ensuring a zero-resonance design that effectively eliminates the shortcomings associated with plastic or lightweight steel alternatives. Complementing these improvements, purpose-selected turntable feet effectively isolate the T2 W from ambient vibrations present in the vicinity of your hi-fi system.

New Tonearm & Anti-Skating

The tonearm on the T2 W has been improved with a longer arm tube. With its 9" effective length and stiff aluminium construction, this one-piece tonearm also features new updated low-friction bearings to accommodate the increased length and diameter for absolute accuracy in use. Besides the clean and stylish looks, the integrated headshell won`t cause any additional vibrations either, and is a big improvement over other detachable, screwed-on or glued-on headshells! The T2 W also comes brand new with an adjustable spring-based anti-skating mechanism that optimizes performance and extracts the utmost potential from your cartridge.

Speed Control, Motor and Drive
The motor and drive system in the T2 W remain identical to those found in the T1. The motor drives a belt system, connected to our newly designed sub-platter exclusive to the T-line. This sub-platter is mounted on an ultra-precise 0.001mm main bearing with a hardened steel axle and brass bushing. Where most alternative products may use un-regulated DC motors with wide speed fluctuations, the T2 W features our proven system of an electronically regulated, precision-speed AC motor. The T2 W also comes with electronic speed switching between 33 and 45 RPM. The result is a low-noise, stable drive system for the turntable.

PRO-JECT AUDIO SYSTEMS www.project-audio.com

Technical data and price changes reserved. Page 3/4

Completely New Built-in Phono Stage
The T2 W has a high-quality dual stage split-passive MM phono preamp this is the first time a Pro-Ject turntable has used an integrated phono-preamp of this level. We considered this a necessity in order to maximize the Wi-Fi performance. We wanted a truly stunning phono stage to match and give the T2 W unrivalled longevity and audio performance. Supplied with a high-value Sumiko Rainier MM cartridge (MSRP 175), this is a true hi-fi playback system with no corners cut.

PRODUCT INFORMATION

Streaming and phono board: careful PCB layout, huge size of phono stage (on the right) carefully separated from digital
components on the left
Semi-balanced phono cable
Like the T1, the T2 W is then finished with super shielded, semi-symmetrical, low-capacitance phono cables, purpose-designed by Pro-Ject not off-the shelf RCA cables. There is also a dust cover for extra protection and a felt mat to protect your records.

PRO-JECT AUDIO SYSTEMS www.project-audio.com

Technical data and price changes reserved. Page 4/4

TECHNICAL INFORMATION

T2 W
How to stream without UPNP - For Bluesound and Apple
Some manufacturers do not support UPNP streaming. However there is a workaround by manuall adding a radio station via TuneIn for example. This can be done on any streaming devices that uses the TuneIn webradio service or supports adding custom radio stations in any other way. This is also a great way to listen to the T2 W on any webbrowser!
1) Start secondary stream (note: secondary stream is only available as MP3). Advanced Settings -> Secondary stream (*please note, there is currently a display bug, the link seems to be cut off, but you just need to scroll right to get to the complete link)

2) With this way you can also listen to the T2 W in any webbrowser! Simply copy the stream address into your webbrowser. If you do that on your phone, you have your vinyl with you on the go always!

It is also possible to add custom radio stations. For example on Bluesound devices or in Roon you can add a custom radio station and copy/type the T2 W stream address there.

Please find a guide on how to do that with Bluesound and Apple devices on the next page.
PRO-JECT AUDIO SYSTEMS www.project-audio.com

Page 1/2

TECHNICAL INFORMATION
Bluesound: Use the secondary stream address to add a custom radio station. In the BluOS App for Android and iOS, you can now save an Internet Stream as a Custom Station in TuneIn. Select TuneIn from the Navigation Drawer. Select Favorites, then Add Custom Station. When prompted Name your Station and enter the Internet address or URL of the stream and select OK. Your named Custom Station will now appear as a TuneIn Favorite for easy access.

Apple Airplay:

Enter secondary stream address here

Long press on the stream link -> Open Link -> Press Airplay symbol -> Choose which device to play to

PRO-JECT AUDIO SYSTEMS www.project-audio.com

Page 2/2

References

Adobe Acrobat Pro (32-bit) 23.8.20470