Redexim Verti-Drain 7626 Parts Manual

Version: 2338

Main Unit Assemblies

Exploded view illustrating the main components of the Verti-Drain 7626 unit.

Item	Part Number	Description	Quantity
1	911.260.404	Angle setting label VD	1
2	900.260.403	Logo Label	2
3	900.260.420	Decall PTO 300 500	1
4	900.280.402	Safety decall manual	1
5	900.280.404	Decall cut off fingers	2
6	911.260.402	Decall Verti-drain	3
7	911.280.404	Decall close cover	2
8	911.280.402	Safety Decall Verti-Drain	2
9	911.260.430	Label 7626	2
10	900.260.412	Heigth label 150-400	2
1	468.020.750	Cover	1
2	470.061.710	Lock plate	2
3	590.342.700	Clamp	2
4	456.269.048	Rear cover VD7526-7626	1
5	2281782	TOP PTO protection cover	1
6	2282350	Bottom PTO Protection	1
7	402.120.120	Distance bush	2
8	464.100.600	Rubber stop 50x58 M10	2
9	830.080.080	Self Lock Nut M8 - ISO 10511	18
10	816.080.300	Bolt M8 x 30 - DIN 7991	8
11	804.080.200	Bolt M8 x 20 - ISO 4017	8
12	804.060.200	Bolt M6 x 20 - ISO 4017	12
13	826.060.060	Nut M6 - DIN 934	12
14	844.060.060	Winged nut	12
15	864.120.030	Washer M12 - ISO 7089	2
16	830.120.120	Self Lock Nut M12 - ISO 10511	10
17	802.120.450	Bolt M12 x 45 - ISO 4014	2
18	864.100.030	Washer M10 - ISO 7089	20
19	804.100.300	Bolt M10 x 30 - ISO 4017	18
20	864.080.024	Large washer M8 - DIN 9021	2
21	804.080.350	Bolt M8 x 35 - ISO 4017	2
22	444.803.100	Toolbox Complete	1
23	804.120.400	Bolt M12 x 40 - ISO 4017	8
24	599.031.000	Foam rubber L=100	8
25	464.061.370	Cover support	8
26	468.083.060	Set of tools	1
27	456.029.136	Front cover left 7626	1
28	456.029.134	Front cover right 7626	1
29	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
16	844.060.060	Winged nut	12
17	864.120.030	Washer M12 - ISO 7089	2
18	830.120.120	Self Lock Nut M12 - ISO 10511	10
19	802.120.450	Bolt M12 x 45 - ISO 4014	2
20	864.100.030	Washer M10 - ISO 7089	20
21	804.100.300	Bolt M10 x 30 - ISO 4017	18
22	864.080.024	Large washer M8 - DIN 9021	2
23	804.080.350	Bolt M8 x 35 - ISO 4017	2
24	444.803.100	Toolbox Complete	1
25	804.120.400	Bolt M12 x 40 - ISO 4017	8
26	599.031.000	Foam rubber L=100	8
27	464.061.370	Cover support	8
28	468.083.060	Set of tools	1
29	456.029.136	Front cover left 7626	1
30	456.029.134	Front cover right 7626	1
31	468.030.530	Toolbox contraplate	1
1	468.020.750	Cover	1
2	456.029.132	Front cover left 7626	1
3	470.061.710	Lock plate	2
4	590.342.700	Clamp	2
5	456.269.048	Rear cover VD7526-7626	1
6	456.029.130	Front cover right 7626	1
7	2281782	TOP PTO protection cover	1
8	2282350	Bottom PTO Protection	1
9	402.120.120	Distance bush	2
10	464.100.600	Rubber stop 50x58 M10	2
11	830.080.080	Self Lock Nut M8 - ISO 10511	18
12	816.080.300	Bolt M8 x 30 - DIN 7991	8
13	804.080.200	Bolt M8 x 20 - ISO 4017	8
14	804.060.200	Bolt M6 x 20 - ISO 4017	12
15	826.060.060	Nut M6 - DIN 934	12
11	830.100.100	Self Lock Nut M10 - ISO 10511	14
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4
1	830.200.200	Self Lock Nut M20 Din 985 h=17	3
2	802.200.700	Bolt M20 x 70 - ISO 4014	2
3	802.201.700	Bolt M20 x 170 - ISO 4014 Class 8.8	1
4	802.220.700	Bolt M22 x 70 - ISO 4014	2
5	830.220.220	Self Lock Nut M22 - ISO 10511	8
6	866.200.020	Spring Washer M20 - Din 127	4
7	802.200.900	Bolt M20 x 90 - ISO 4014	2
8	802.201.000	Bolt M20 x 100 - ISO 4014	2
9	864.100.030	Washer M10 - ISO 7089	4
10	802.221.300	Bolt M22 x 130 - ISO 4014	6
11	830.100.100	Self Lock Nut M10 - ISO 10511	4
12	804.100.400	Bolt M10 x 40 - ISO 4017	4
13	523.100.570	Linch Pin d10	3
14	468.202.490	3-Point bottom link plate	4
15	406.200.700	Distance bush Ø33.7/Ø20.5 L=69.5	1
16	464.205.220	Top link support strip	2
17	406.220.140	Distance bush Ø35/Ø22.5 L=13.5	12
18	521.280.950	Pin Cat. 2 - 28,6 x 95	2
19	521.251.380	Top link pin	1
20	464.203.860	Top link strip	2
21	494.261.020	Central bar	1
22	464.251.250	Lock strip	2
23	412.210.250	Distance bush	4
24	412.210.030	Shim 3mm	4
25	412.210.020	Shim 2mm	4
26	464.031.400	Distance plate	2
27	468.085.070	Tine angle adjustment lever	1
28	466.279.000	Support bolt assy central bar	2
29	848.791.360	U-Bolt M14	2
30	802.160.750	Bolt M16 x 75 - ISO 4014	2
31	402.160.100	Distance washer Ø16.5/Ø50 L=10	4
32	830.140.140	Self Lock Nut M14 - ISO 10511	4
33	830.160.160	Self Lock Nut M16 - ISO 10511	2
34	468.080.750	Lock strip	2
35	494.270.138	Main frame 7626	1
36	468.253.452	Gearbox clamp right	1
37	468.253.450	Gearbox clamp left	1
38	814.160.800	Bolt M16 x80 - DIN 912	4
39	814.161.100	Bolt M16 x 110 - DIN 912	4

PTO Components (Various Types)

Exploded views of PTO shafts, universal joints, and clutch mechanisms.

Item	Part Number	Description	Remarks	Quantity
1	BEN F1B08	Flange yoke		1
2	BEN F060	Bush		1
3	BEN F334	Hub		1
4	BEN 90934	Conic bolt and nut		1
5	BEN F030/S	Lining ring		4
6	BEN F070	Inner plate		2
7	BEN F1180	Pressure plate		1
8	BEN F0111	Spring		8
9	BEN F10100	Bolt and nut		8
10	BEN F080	Drive plate with hexagon		1
11	190000243	Outer roll pin		2
12	BEN PT140150	End yoke with quick lock		1
13	BEN PT140518	Inner tube yoke		1
14	BEN PT147350	Outer tube yoke		1
15	BEN PT155479	Universal joint assembled	Cut to correct length	2
16	BEN PT155954	Inner tube	Cut to correct length	1
17	BEN PT155956	Outer tube	Cut to correct length	1
18	BEN PT156265	Safety guard group	Cut to correct length	1
1	190000271	Inner roll pin		1
2	190000243	Outer roll pin		1
3	180018004	Cross and 4x circlip kit		2
4	1510182421	Inner tube yoke		1
5	1510182411	Outer tube yoke		1
6	1522802160700	V-series Outer tube	7626	1
7	153280116	V-series Inner tube	7626	1
8	1410284231	Complete collar yoke		1
9	1423800169851	Complete shield		1
10	1510180161	Flanged yoke		1
11	180019019	Bush		1
12	180017430	Pressure plate		2
13	180019018	Lining ring		4
14	1510194181	Clutch support T48		1
15	165000857	Bolt & nut M10x1.5x70		8
16	165000589	Tapered Pin 1 3/4" kit	Retighten every 40 hours	1
17	180017451	Belleville spring		1
18	180019115	Intermediate plate		1
1	141028423	Complete collar yoke C12		1
2	180018004	Cross and 4x circlip kit		2
3	151018241	Outer yoke		1
4	190000243	Roll pin for outer tube		1
5	1522802030730	Outer tube	7626	1
6	1522802140730	Outer tube	7626H (For use with wheelkit)	1
7	159280185	Inner tube	7626	1
8	159280192	Inner tube	7626H (For use with wheelkit)	1
9	190000271	Roll pin for inner tube		1
10	151018242	Inner yoke		1
11	180014022	Spring		8
12	151018016	Flanged yoke		1
13	180019019	Bush		1
14	180019018	Lining ring		4
15	165000503	Bolt & Nut		2
16	151019012	Clutch support F44		1
17	180019014	Inner plate		2
18	180019115	Intermediate plate		1
19	180019116	Pressure plate		1
20	165000548	Bolt & Nut		8
21	1423800379850	Complete guard	7626	1
22	1423800299850	Complete guard	7626H (For use with wheelkit)	1

Tines and Related Components

Details on various types of tines (solid, hollow, replacement, cross, chisel) and associated components like multi-tine blocks and turf hold-down fingers.

Tine Type	Mounting Ø (mm)	Tine Size (mm)	Tine Size (inch)	Part #	Adapter	Quantity
Solid Tines	5	5 x 125	3/16 x 5	311.105.125	J or multi-tine block mini	40+J
Solid Tines	5	8 x 150	5/16 x 6	311.108.150	K or multi-tine block	40+K or 80+N+U+W
Solid Tines	5	8 x 175	5/16 x 7	9990056	K or multi-tine block	40+K or 80+N+U+W
Solid Tines	5	8 x 250	5/16 x 10	9990059	K - Don't use in MTH. Will bend	40+K
Solid Tines	12	12 x 150	1/2 x 6	311.112.150		40
Solid Tines	12	12 x 200	1/2 x 8	311.112.200		40
Solid Tines	12	12 x 225	1/2 x 9	311.112.225		40
Solid Tines	12	12 x 250	1/2 x 10	2381837		40
Solid Tines	12	12 x 300	1/2 x 12	2381838		40
Solid Tines	18	18 x 200	3/4 x 8	311.118.200	L or non needed	20+L
Solid Tines	18	18 x 225	3/4 x 9	311.118.225	L or non needed	20+L
Solid Tines	18	18 x 250	3/4 x 10	2381841	L or non needed	20+L
Solid Tines	18	18 x 300	3/4 x 12	2382638	L or non needed	20+L
Solid Tines	18	18 x 350	3/4 x 14	311.118.350	L or non needed	20+L
Solid Tines	18	18 x 400	3/4 x 16	2382639	L or non needed	20+L
Solid Tines	24	24 x 225	1 x 9	311.124.225		20
Solid Tines	24	24 x 350	1 x 14	311.124.350		20
Solid Tines	24	24 x 400	1 x 16	2382640		20
Hollow Tines	8	10 x 6 x 80	3/8 x 1/4 x 3	311.210.080	K or multi-tine block	40+K or 80+N+U+W
Hollow Tines	8	10 x 6 x 125	3/8 x 1/4 x 5	311.210.127	K or multi-tine block	40+K or 80+N+U+W
Hollow Tines	12	16 x 10 x 150	5/8 x 3/8 x 6	311.216.150		40
Hollow Tines	12	16 x 10 x 175	5/8 x 3/8 x 7	9990022		40
Hollow Tines	12	19 x 12 x 150	3/4 x 1/2 x 6	311.219.150		40
Hollow Tines	18	19 x 12 x 200	3/4 x 1/2 x 8	311.219.200	L or non needed	20+L
Hollow Tines	12	19 x 12 x 200	3/4 x 1/2 x 8	311.219.201		40
Hollow Tines	18	19 x 12 x 225	3/4 x 1/2 x 9	311.219.225	L or non needed	20+L
Hollow Tines	12	19 x 12 x 225	3/4 x 1/2 x 9	311.219.226		40
Hollow Tines	12	19 x 12 x 250	3/4 x 1/2 x 10	9990040		40
Hollow Tines	18	19 x 12 x 250	3/4 x 1/2 x 10	9990023	L or non needed	20+L
Hollow Tines	18	25 x 16 x 200	1 x 5/8 x 8	311.225.200	L or non needed	20+L
Hollow Tines	18	25 x 16 x 225	1 x 5/8 x 9	311.225.225	L or non needed	20+L
Hollow Tines	18	25 x 17 x 250	1 x 5/8 x 10	9990024	L or non needed	20+L
Hollow Tines	18	29 x 19 x 250	1 1/8 x 3/4 x 10	9990066	L or non needed	20+L
Solid Tines	24	32 x 21 x 300	1 1/4 x 13/16 x 12	9990034		20
Solid Tines	18	32 x 21 x 300	1 1/4 x 13/16 x 12	9990041	L or non needed	20+L
Replacement Tubes	12	16 x 10 x 150	5/8 x 3/8 x 6	311.716.150	9990010	40
Replacement Tubes	12	16 x 10 x 175	5/8 x 3/8 x 7	9990036	9990010	40
Replacement Tubes	12	19 x 12 x 150	3/4 x 1/2 x 6	311.719.150	9990012	40
Replacement Tubes	18	19 x 12 x 200	3/4 x 1/2 x 8	311.719.200	9990012	20+L
Replacement Tubes	12	19 x 12 x 200	3/4 x 1/2 x 8	311.719.201	9990012	40
Replacement Tubes	18	19 x 12 x 225	3/4 x 1/2 x 9	311.719.225	9990012	20+L
Replacement Tubes	12	19 x 12 x 225	3/4 x 1/2 x 9	311.719.225	9990012	40
Replacement Tubes	12	19 x 12 x 250	3/4 x 1/2 x 10	9990037	9990012	40
Replacement Tubes	18	19 x 12 x 250	3/4 x 1/2 x 10	9990037	9990012	20+L
Replacement Tubes	18	25 x 16 x 200	1 x 5/8 x 8	311.725.200	9990014	20+L
Replacement Tubes	18	25 x 16 x 225	1 x 5/8 x 9	311.725.225	9990014	20+L
Replacement Tubes	18	25 x 17 x 250	1 x 5/8 x 10	9990038	9990014	20+L
Replacement Tubes	18	29 x 19 x 250	1 1/8 x 3/4 x 10	9990067	9990016	20+L
Solid Tines	24	32 x 21 x 300	1 1/4 x 13/16 x 12	9990039		20
Solid Tines	18	32 x 21 x 300	1 1/4 x 13/16 x 12	9990041	L or non needed	20+L
Cross Tines	8	12 x 90	1/2 x 3 1/2	9990020	K or multi-tine block	40 + K
Chisel Tines	12	4.8 x 19 x 175	3/16 x 3/4 x 7	311.619.175		40
Chisel Tines	12	4.8 x 19 x 120	3/16 x 3/4 x 4 3/4	311.619.120		40
Composed Hollow Tines	19	5 x 30 x 90	3/16 x 1 3/16 x 3 1/2	311.619.127		40
Clip	A	12	1/2	311.120.690	(Straight)	40
Clip	B	18	3/4	311.180.782	(Straight)	20
Clip	C	12	1/2	311.180.780		40
Clip	D	24	1	311.240.862	(Straight)	20
Clip	E	18	3/4	311.240.860	Clip	20
Hollow tine tube (folded)	F	16	5/8	438.160.160		40
Hollow tine tube (folded)	G	22	7/8	438.220.220		40/20
Hollow tine tube (folded)	H	30	1 3/16	438.300.300		20
Tine Size (mm)	Tine Size (inch)	Part #	Quantity	Combine with:
16 x 150	5/8 x 6	317.316.150	40	A and F
16 x 200	5/8 x 8	317.316.200	40	A and F
22 x 150	7/8 x 6	317.322.150	40	B or C and G
22 x 250	7/8 x 10	317.322.250	20	B or C and G
22 x 150	7/8 x 6	317.322.150	40	B or C and G
22 x 250	7/8 x 10	317.322.250	20	B or C and G
30 x 150	1 3/16 x 6	317.330.150	20	E and H
30 x 225	1 3/16 x 9	317.330.220	20	E and H
30 x 300	1 3/16 x 12	317.330.300	20	E and H

Optional Bogy Kit

Exploded view diagrams and part lists for the optional bogy kit.

Item	Part Number	Description	Quantity
1	494.911.970	Draw bar	1
2	2282906	Top link	1
3	2490830	Pin d.25	1
4	523.051.000	R-clip Round 5, DIN 11024	1
5	470.203.354	Towing hook	1
6	802.200.650	Bolt M20 x 65 - ISO 4014	4
7	830.200.200	Self Lock Nut M20 Din 985 h=17	4
8	2283017	Spindle assembly P560	1
9	830.160.160	Self Lock Nut M16-ISO 10511 Class 10	16
10	802.161.000	Bolt M16 x 100 - ISO 4014	8
11	831.160.160	Self Lock Nut M16x1.5 - ISO 10511	10
12	804.160.550	Bolt M16 x 55 - ISO 4017	4
13	804.160.500	Bolt M16 x 50 - ISO 4017	4
14	808.010.060	Hex Bolt 1"-8x6" UNC - ANSI B18.2.1	4
15	838.010.220	Self Lock Nut 1 inch UNC - DIN 985	6
16	808.010.051	Hex Bolt 1"-8x5" UNC - ANSI B18.2.1	2
17	830.080.080	Self Lock Nut M8 - ISO 10511	11
18	802.080.450	Bolt M8 x 45 - ISO 4014	4
19	804.080.350	Bolt M8 x 35 - ISO 4017	3
20	864.270.040	Washer DIN 125 - A 27	4
21	494.064.267	Static frame VD7626	1
22	494.094.162	Rotating frame	1
23	519.050.921	Wheel axle 50x50	1
24	519.050.922	Wheel axle with hydraulic brake	1
25	464.151.600	Wheel axle lock plate	2
26	534.353.000	Hydraulic Cylinder 30-60, Stroke 300mm	2
27	544.172.400	Cavity Bolt 3/8"	4
28	549.170.044	Banyo connector 3/8" straight	2
29	544.170.122	Straight nipple BSP 3/8" x pipe 12-(M18)	4
30	874.170.020	Copper washer 3_8	16
31	549.170.043	Banyo connector 3/8" straight	2
32	535.401.001	Pressure controlled one way valve 3/8"	2
33	544.170.120	Nipple BSP 3_8" x pipe 12 (M18)	4
34	412.260.150	Distance bush	4
35	511.660.305	Wheel 26x12 inch complete	2
36	511.660.305RIM	Rim 26x12	2
37	511.660.305TIRE	Tire 26x12 8ply	2
38	547.150.150	Hose clamp double 15mm	20
39	547.300.510	Cover plate hose clamp 2x15 - 2x18	12
40	544.124.125	T-Connector 12x12x12	2
41	541.170.575	Hose TL=575 HST10 PGLO1018 + PGLO101890	2
42	541.172.000	Hose TL=2000 HST10 PGLO1018 + PGLO101890	2
43	464.042.560	Bracket	1
44	547.180.180	Hose clamp double 18mm	4
45	802.080.500	Bolt M8 x 50 - ISO 4014	6
46	402.080.180	Bush Ø20xØ9x18	4
47	468.012.160	Shim plate	4
48	802.080.750	Bolt M8 x 75 - ISO 4014	6
49	468.150.500	Spacer	1
50	549.010.500	Hose binder L=500	1
51	541.132.502	Hose NSK6-1/4" TL=2500 PN68 + PN64	2
52	541.174.850	Hose, TL=4850 HST10 PGLO1018+PN108	2
53	545.210.800	Quick connector male 1/2"	1
54	802.080.600	Bolt M8 x 60 - ISO 4014	4
55	874.130.020	Copper washer 1/4"	2
56	874.210.020	Copper washer 1_2	4

Shim Plate and Hydraulic Hose Routing

Diagram illustrating shim plate installation and hydraulic hose routing.

	Redexim VERTI-DRAIN 7215 User Manual Comprehensive user manual for the Redexim VERTI-DRAIN 7215, covering operation, safety, maintenance, and technical specifications. Includes instructions for setup, adjustments, and troubleshooting.
	Redexim Verti-Drain 1513-1517 User Manual Comprehensive user manual for the Redexim Verti-Drain 1513-1517, covering safety guidelines, technical specifications, operation, maintenance, and troubleshooting.
	Redexim RINK DS550SP Parts Manual Comprehensive parts manual for the Redexim RINK DS550SP turf maintenance machine, detailing components and part numbers with diagrams.
	Redexim Verti-Drain 7416 User Manual This user manual provides comprehensive instructions for the Redexim Verti-Drain 7416, covering setup, operation, maintenance, and troubleshooting. It details technical specifications, safety guidelines, and optional accessories.
	Redexim Speed Brush User Manual Comprehensive user manual for the Redexim Speed Brush, covering safety instructions, technical data, installation, operation, maintenance, and troubleshooting for agricultural and turf care applications.
	Betjeningsvejledning Verti-Drain 7215 Betjeningsvejledning for Verti-Drain 7215, en maskine designet for jordbearbejdning. Denne vejledning indeholder vigtige sikkerhedsinstruktioner, tekniske data, vedligeholdelsesprocedurer og fejlfindingstips for at sikre optimal og sikker brug af Verti-Drain 7215.

Main Unit Assemblies

PTO Components (Various Types)

Tines and Related Components

Optional Bogy Kit

Shim Plate and Hydraulic Hose Routing

Related Documents