scott-sports.com
Instruction Manual for SCOTT models including: 2024, 2025, 2025 PATRON Scale RC Team Bike, PATRON Scale RC Team Bike, Scale RC Team Bike, Team Bike
File Info : application/pdf, 22 Pages, 6.15MB
DocumentDocument2025 SCOTT PAT R O N / PAT R O N ST M A N U A L 2024 PATRON | ENGLISH 1 | PATRON CONTENT THE PATRON / PATRON ST SHOULD BE ADJUSTED EXACTLY TO THE RIDER FOR MAXIMUM SAFETY AND RIDEABILITY. Please contact your authorized SCOTT dealer for advice in order to avoid technical problems or any harm. GEOMETRY & TECHNICAL DATA 03 HEADSET ADJUSTMENT 05 BATTERY INSTALLATION 06 MOTOR INSTALLATION 09 SHOCK AND SHOCK COVER 10 BOSCH POWERMORE 11 CABLE ROUTING 12 GENERAL SPARE PARTS 18 MANUFACTURE'S GUARANTEE 21 LEGEND TORQUE REQUIRED TASK DIFFICULTY T 25 TORX TOOL SIZE 8 HEX TOOL SIZE 5 Nm TORQUE AMOUNT GREASE REQUIRED NO GREASE CARBON GREASE THREADLOC BEARING FIT 2024 PATRON | ENGLISH 2 | PATRON GEOMETRY & TECHNICAL DATA SEATPOST SEATPOST CLAMP TRAVEL SHOCK LENGTH SHOCK STROKE REAR AXLE HEADSET mm 31.6 HARDWARE M.FRAME mm Trunnion mm 34.9 HARDWARE LINKAGE mm 8 x 20 mm 150 MAX TYRE WIDTH in 2.6 mm 185 CHAINLINE mm 55 mm 55 MAX CHAINRING Tooth 36 mm 12 x 148 MAX ROTOR mm 200 Rr 200 Fr mm O52/142 - O52/140 BOSCHCONNECTMODULE not compatible 2025 PATRON SM MED LG XL SM ST MED ST LG ST XL ST A Head tube angle ° 65.8 65.8 65.8 65.8 64.9 64.9 64.9 64.9 B Head tube length mm 120 125 135 145 120 125 135 145 C Top tube horizontal mm 579.3 605.5 626.6 657 582.4 607.9 629.7 660.2 D standover height mm 719 719 729 732 719 719 729 732 E BB offset mm -36.2 -36.1 -35.9 -35.8 -28.4 -28.4 -28.4 -28.5 F BB height mm 340.8 340.9 341.1 341.2 348.6 348.6 348.6 348.5 G Wheelbase mm 1212.8 1234.9 1264.7 1298.4 1222.3 1244.5 1274.2 1308 I BB center to TST mm 405 435 470 500 405 435 470 500 J Seat angle ° 77.4 77.2 77.2 77.2 76.4 76.3 76.3 76.3 K Chainstay mm 453.5 453.5 453.5 453.5 454 454 454 454 L Reach mm 439.4 459.3 484.7 514.2 428.3 448.3 473.9 503.4 M Stack mm 643 647.4 656.3 665.1 650.5 655 664.2 673.3 Fork Length mm 561 561 561 561 584 584 584 584 Trail mm 120.5 120.6 120.8 120.9 127.9 127.9 127.9 127.9 2024 PATRON | ENGLISH 3 | PATRON GEOMETRY & TECHNICAL DATA CONT. PATRON There is a stop inside the seat tube to avoid damaging the frame internals. MAX INSERTION (MM): SMALL: 205 MEDIUM: 232 LARGE: 267 XL: 298 All Patron bikes will use the UDH hanger. 2024 PATRON | ENGLISH 4 | PATRON HEADSET ADJUSTMENT PATRON SLACKER STEEPER It is important to install the headset correctly depending on the setup required. Make sure the angle indication markers are set opposite each other. Bikes will be delivered with 0,6° cups installed. CUP SIZE (MM): SMALL: 120, MEDIUM: 125, LARGE: 135 XL: 135 288251 SYN HEADSET ZS56/28.6 - ZS56/40 MTB 290060 SCO HEADSET CUP KIT SPARK 22 DO NOT USE A STANDARD HEADSET TOOL! 2024 PATRON | ENGLISH 5 | PATRON PATRON BATTERY INSTALLATION BATTERY FIXATION MUST ONLY BE CARRIED OUT BY A SCOTT AUTHORISED DEALER USING THE CORRECT GAUGE AND TOOLING ! 6 5 3 1 4 7 2 ITEM QTY DESCRIPTION BOSCH ITEM SCOTT 1 1 Battery Cradle Inverted EN12.200.0U0 424333 SCO eRIDE Bosch Battery mount Option 8 2 1 Battery Adapter 2 EB12.100.015 294641 SCO eRIDE Bosch Battery Adapter 2 22 3 1 Battery Damper Foil Patron Plug EB12.200.0LK 424341 SCO eRIDE Bosch Foam damper 25 4 2 Battery Clamping Plate Patron 25 (Screws Not Included) N/A 424336 SCO eRIDE Batt Clamping plate 25 5 1 Battery Powertube Horizontal 800Wh EB12.100.050 424338 SCO eRIDE Bosch Powertube 800 H 25 6 6 Battery PT800 Locking Assembly Inverted EB12.100.050 424334 SCO eRIDE Bosch Lock Assembly Patron 25 7 4 Battery Screw For Holder M5x9 EB12.100.01Y 424337 SCO eRIDE Bosch screw for Batt plate 25 2024 PATRON | ENGLISH 6 | PATRON BATTERY INSTALLATION CONT. PATRON 01 Insert the battery, bottom end first. 02 Turn and hold the key and press in the battery, you will hear the first click. 03 Let go of the key, then push the battery one more time. You will hear a second click to secure. 04 Place the bottom part of the battery cover into position. 2024 PATRON | ENGLISH 7 | PATRON BATTERY INSTALLATION CONT. PATRON 05 Lift up the lock tab, then press the cover into place. You will hear a click when engaged fully. 2024 PATRON | ENGLISH 8 | PATRON PATRON MOTOR INSTALLATION MOTOR FIXATION MUST ONLY BE CARRIED OUT BY A SCOTT AUTHORISED DEALER USING THE CORRECT TOOLING ! 7 6 4 9 5 10 11 ITEM 1 2 3 4 5 6 7 8 9 10 11 QTY DESCRIPTION 1 Drive Unit CX BDU38YY 1 DU BDU38YY Lockring 1 O-Ring 1 Drive Unit Bezel 1 Front Motor Bolt Wide 1 Rear Motor Bolt 2 Motor Wide adapter 2 Motor Assembly Nut 2 Motor Bolt Sleeve 1 Rim Magnet 1 Rim Magnet Adapter 1 2 8 3 BOSCH ITEM EB11.100.01C EB11.200.0JH 1270016119 EB11.200.0KD EB11.200.0T1 EB11.200.12M EB11.200.12H EB11.200.03C EB11.200.0GK EB11.200.015 EB11.200.025 2024 PATRON | ENGLISH 9 | PATRON SHOCK AND SHOCK COVERS PATRON Scott Nude 6 rear shock cover is latched at the top and magnetic at the base, it will cover the complete shock. Piggyback rear shock cover only covers half the opening, with a small base plate. Both parts have a screw fixation. Both rear shock covers will use the upper shock cover bracket. This also doubles as a cable guide for all cable apart from Bosch components wires. NO COIL SHOCKS PERMITTED ! 2024 PATRON | ENGLISH 10 | PATRON BOSCH POWERMORE PATRON Patron's are Bosch PowerMore ready, no configuration update is required. You will need the follow Bosch parts: BOSCH POWERMORE HOLDER: EB12.110.01Q BOSCH POWERMORE CABLE 250mm: EB12.120.08J 2024 PATRON | ENGLISH 11 | PATRON CABLE ROUTING PATRON CABLE ROUTING OVERVIEW FOR BOSCH COMPONENT CONNECTIONS PLEASE CONSULT YOUR AUTHORISED SCOTT SPORTS DEALER ! 2024 PATRON | ENGLISH 12 | PATRON CABLE ROUTING CONT. PATRON REAR BRAKE CABLE ROUTING Guide from the brake calliper to brake lever, enter mid point in the chainstay, exit front of the chainstay, then enter the main frame. Cross behind the shock on the drive side, through the seat tube on the drive side. Zip tie to the frame cable holder, then zip tie to the shock cover plate. Along the inside of the top tube and exit on the right side of the head tube. 2024 PATRON | ENGLISH 13 | PATRON CABLE ROUTING CONT. PATRON REAR SHOCK CABLE ROUTING Guide from the handlebar lever to the shock. Enter the headtube on the left side, and along the inside of the top tube. Zip tie to the shock cover plate on the drive side. 2024 PATRON | ENGLISH 14 | PATRON CABLE ROUTING CONT. PATRON REAR DERAILLEUR CABLE ROUTING Guide from the shifter to the rear derailleur. Enter the headtube on the right side and along the inside of the top tube. First attach to the left side of the shock cover plate, then again to the left side frame cable holder. Cross over behind the rear shock and enter the chainstay on the right side. 2024 PATRON | ENGLISH 15 | PATRON CABLE ROUTING CONT. PATRON 1 2 DROPPER SEATPOST CABLE ROUTING Guide from dropper lever to the post, enter at the head tube on the left side and along the inside of the top tube. Install a protective tube to the dropper cable. Then first zip tie the protective tube to the shock cover bracket left side of the shock cover (1), then again to the left side frame cable holder (2). Guide the cable housing through the protection tube and loop it upto the dropper cable interface. Cable loop should be long enough to allow dropper height adjustment. 2024 PATRON | ENGLISH 16 | PATRON CABLE ROUTING PATRON REAR LIGHT CABLE ROUTING Guide from the motor to the light. The cable must go below the chainstay / seatstay pivot, and enter the main frame via the main cable guide. 2024 PATRON | ENGLISH 17 | PATRON GENERAL SPARE PARTS (illustration only) PATRON 286000 SCO DROPOUT SRAM UDH 21 8 25 Nm Reverse Thread 290016 SCO AXLE RWS REAR 148X12 SPARK PLUG 22 10 Nm 297749 SCO eRIDE BOSCH RIM SPEED SENSOR 22 424177 SCO eRIDE MOTOR COVER OPTION 7 PATRON 25 T 25 5 Nm 424174 SCO eRIDE SHOCK COVER PATRON 25 T 15 3 Nm 2024 PATRON | ENGLISH 18 | PATRON GENERAL SPARE PARTS (illustration only) PATRON 424175 SCO eRIDE SHOCK COVER PB PATRON 25 T 15 3 Nm 425428 SCO eRIDE BAT COVER PATRON 25 T 15 3 Nm 424169 SCO eRIDE CHARGE PORT ASSEMBLY SPIN 25 T 20 2Nm 424183 SCO eRIDE TT REMOTE ADAPT PATRON CARB 25 T 10 0.5 Nm 424336 SCO eRIDE BATT CLAMPING PLATE 25 424337 SCO eRIDE BOSCH SCREW FOR BATT PLATE 25 T 25 4.5 Nm 2024 PATRON | ENGLISH 19 | PATRON GENERAL SPARE PARTS (illustration only) PATRON 424392 SCO eRIDE SEATPOST CLAMP PATRON CB 25 T 25 6 Nm 424169 SCO eRIDE CHARGE PORT ASSEMBLY SPIN 25 T 10 2 Nm 424541 SCO eRIDE DT CABLE HOLDER PATRON 25 (for Bosch wires only) 2024 PATRON | ENGLISH 20 | MANUFACTURER'S GUARANTEE, When purchasing a new SCOTT bicycle from an authorized SCOTT dealer, SCOTT grants a manufacturer's guarantee subject to the following provisions. CONDITIONS The manufacturer's guarantee is only granted to the first-time buyer of a SCOTT bicycle who has purchased it from an authorized SCOTT dealer. The manufacturer's guarantee only applies if the bicycle is registered to the first buyer at www.scott-sports.com within ten days of purchase. D U R AT I O N The manufacturer's guarantee is granted from the date of purchase for a period of five years on bicycle frames and rear ends. The guarantee period is reduced to three years, if the SCOTT bicycle is not serviced at least once a year by an authorized SCOTT dealer. Maintenance services must be carried out in accordance with the maintenance instructions in the SCOTT manual and must be confirmed there by the stamp and signature of the authorized SCOTT dealer. For frames and rear ends of Category 5 bicycle models and for rigid forks manufactured by SCOTT, the duration of the manufacturer's guarantee is limited to two years. If a defect on the SCOTT bicycle is remedied within the scope of a manufacturer's guarantee or a warranty claim, the duration of the manufacturer's guarantee is not extended. The manufacturer's guarantee ends, when the first-time buyer transfers ownership of the SCOTT bicycle to a third person. ASSERTION The manufacturer's guarantee is provided by SCOTT Sports SA, Route du Crochet 11, 1762 Givisiez, Switzerland. The buyer must inspect the SCOTT bicycle immediately after purchase and notify his authorized SCOTT dealer at once in writing of any obvious defects. Hidden defects must be reported immediately after their discovery. In the event of a guarantee claim, the SCOTT bicycle must be handed over to an authorized SCOTT dealer. The latter will contact SCOTT to remedy the defect. The assertion of a guarantee claim always requires the presentation of the original proof of purchase as well as the proof of maintenance service in the SCOTT manual. Performance of SCOTT in the event of a guarantee claim In the event of a guarantee claim, SCOTT will, at its own discretion, repair the defect or replace the defective product with a product of similar quality, whereby colour and model deviations are possible. If a repair or replacement is not possible, a purchase price refund will be made taking into account previous use. SCOTT is entitled to commission third parties to remedy the defect. LIMITATIONS The manufacturer's guarantee applies exclusively to frames, swingarms and rigid forks of SCOTT bicycles. Bicycle components are excluded from this manufacturer's guarantee. The manufacturer's guarantee does not apply to normal wear and tear, damage caused by accidents or other excessive force on the SCOTT bicycle, corrosion, improper maintenance, incorrect assembly and assembly of unsuitable components or accessories as well as cosmetic defects, for example in the varnish. The manufacturer's guarantee does not apply to SCOTT bicycles that have been used in a rental shop. MISCELLANEOUS These manufacturer's guarantee provisions apply to all SCOTT bicycles as of model year 2023. Statutory warranty rights of the buyer and guarantees of component manufacturers (Shimano, SRAM etc.) remain unaffected by this manufacturer's guarantee. The place of jurisdiction for all disputes in connection with this manufacturer's guarantee is Freiburg, Switzerland. This manufacturer's guarantee p SCOTT Bikes Category 5 Bikes Year 1 BIKE WARRANTY PERIODS Year 2 Year 3 Year 4 Year 5 is subject to Swiss law to the exclusion of all legislation that refers to foreign law. Regular Warranty Period Option for prolongation according to maintenance intervals shown in manual attached to bikes 2024 PATRON | ENGLISH 21 | FR À DÉPOSER À DÉPOSER EN MAGASIN EN DÉCHÈTERIE OU 2024 PATRON | ENGLISH 22 |