Home - World Accelerator
User Manual for OLIGHT models including: Prowess Versatile EDC Flashlight, Prowess, Versatile EDC Flashlight, EDC Flashlight, Flashlight
TS004 COOL WHITE CCT: 6000-7000K CRI:70 WARM WHITE CCT: 2800-3200K CRI:70 145min 30min 4,500 100% 3min 24% 7% lumens TURBO 100% 1,100 HIGH lumens 300 100% 10h MEDIUM lumens 50 100% LOW lumens
File Info : application/pdf, 1 Pages, 1.95MB
DocumentDocumentUSER MANUAL A versatile EDC flashlight with dual-direction illumination. IN THE BOX 27,000cd 325m 1m IPX7 Magnetic tail cap Holster fixing bracket X2 Plastic Expansion Screws TS004 Table 1 Flashlight (FRONT LIGHT) Vertical Holster USB-C Charging Cable COOL WHITE CCT: 6000-7000K CRI:70 TURBO 4,500 lumens 100% 3min 24% 145min 7% 30min HIGH 1,100 lumens 100% 155min 27% 30min MEDIUM 300 lumens 100% 10h LOW 50 lumens 100% 55h MOONLIGHT 5 lumens 100% 20 days (BACK LIGHT) WARM WHITE CCT: 2800-3200K CRI:70 HIGH 800 lumens 100% 35min 75% 105min MOONLIGHT 2 lumens 100% 20 days 50% 55min 273g/9.63oz (Including Battery) Working temperature 0-40°C (L)145*(D)50mm (L)5.71*(D)1.97in Rechargeable Li-ion Battery 5000mAh3.6V (18Wh) * Above data are tested per ANSI/PLATO FL 1-2019 standard in Olight's labs for reference. Table 2 USB-C Charging Cable Charge Type Cable length Input Time to fully charge USB-A to USB-C cable 0.8m 5V/2A About 2.5 hours Figure 1 Remove the insulating film Figure 2 Charge Indicator Figure 3 ON/OFF Press OFF ON Figure 4 Lockout/Unlock Press and hold >1 sec >2 sec Figure 5 Moonlight Press and hold 1 to 2 sec Moonlight Figure 6 Turbo Front light Operation: Figure 8 Strobe Double press TURBO Or Figure 7 Switch between front light and back light Triple press Or Strobe Figure 9 Change Brightness Level Toggle modes Front light Back light Press and hold Moonlight Turbo Low High Medium Back light Operation: Figure 10 Change Brightness Level (Stepless dimming) Figure 11-2 Battery level indicator (Moonlight mode) Press and hold ON Figure 11-1 Battery level indicator Stepless dimming Figure 12 Magnetic tail cap application 1 2 3 Screw Figure 12 How to use the fixing bracket 1 Figure 13 4 How to take the vertical holster out of the fixing bracket 1 Use tools to punch holes in the wall or wooden board 2 Secure the bracket in place by screwing in the screws 5 Insert the expansion screws 3 Remove the 3M adhesive sticker on the back of the fixing bracket and align it with the hole on the wall (Note: Please stick the 3M adhesive sticker on a flat and smooth wall or car panel) Hang the holster and flashlight Press the vertical holster against the fixing bracket 2 Pull HOW TO OPERATE 1. Product specifications, see Table 1 and Table 2; 2. Operating instructions as below: 2.1 Remove the insulating film before first use, see Figure 1; 2.2 Charge, see Figure 2; 2.3 ON/OFF, see Figure 3; Single press the switch quickly to turn on the light. When turned on, the flashlight will light up at the memorized brightness level. (Moonlight, Low, Medium, and High modes will be memorized when turned off. Turbo mode will be memorized as High mode; High mode output will last for 10 minutes before switching to Medium mode; Strobe mode will not be memorized.) Single press the switch again to turn off the light. The back light retains brightness memory for 1 minute after turning off and switches to the lowest output upon restart. 2.4 Lockout/Unlock, see Figure 4; When the flashlight is on, press and hold the switch (for about 2 seconds) to access lockout mode (the flashlight will enter Moonlight briefly and then switch off to signal lockout mode activation). In lockout mode, if you operate the switch for a non-unlock purpose, the indicator at the center of the switch will briefly light up red to signal that the light is still in lockout mode. To unlock it, please press and hold the switch for about one second until the Moonlight is on. 2.5 Moonlight, see Figure 5; When the flashlight is off, press and hold the switch for over one second to access the Moonlight mode. If the light was turned off in Moonlight mode, simply press the switch. 2.6 Turbo, see Figure 6; Front light: Double press the switch quickly to activate Turbo mode, and double press again to return to the memorized brightness level. If the battery level is low, it returns to a lower output. Back light: When the current brightness is 70%, double press the switch quickly to set the flashlight output to the lowest brightness. When the current brightness is <70%, double press the switch quickly to set it to the highest available brightness. 2.7 Choose between front light and back light, see Figure 7; Move the toggle switch upward for the front light, and downward for the back light. 3. Front light operation 3.1 Strobe, see Figure 8; Press the switch 3 times or more to activate Strobe mode. To quit this mode, single press or press and hold the switch. 3.2 Change brightness level, see Figure 9; When the light is on, press and hold the switch to adjust brightness. The flashlight will cycle through Low, Medium, and High modes, starting from the current brightness level. Release the button to select the desired brightness level. (Note: Moonlight and Turbo modes are not included in this cycle.) 4. Change the brightness level of the back light, see Figure 10; When the light is on, press and hold the switch once to smoothly increase the brightness, and release to select the brightness level. To decrease the brightness level, press and hold again to smoothly decrease the brightness from the current brightness level. When the brightness level reaches its limits at the brightest or lowest setting, the light will flash twice to indicate that it has reached the highest or lowest level. 5. Battery level indicator, see Figure 11-1 & 11-2; 6. How to use the fixing bracket, see Figure 12 Begin by using tools to punch holes in the wall or wooden board, then insert the expansion screws. Next, remove the 3M adhesive sticker on the back of the fixing bracket and align it with the hole on the wall. Finally, secure the bracket in place by screwing in the screws.(Note: Please stick the 3M adhesive sticker on a flat and smooth wall or car panel) 7. How to take the vertical holster out of the fixing bracket, see Figure 13; Press the vertical holster against the fixing bracket, then pull it up and out of the fixing bracket. CAUTION ·Do not look directly at the light source or shine to eyes, or else it may cause temporary blindness or permanent damage to the eyes. ·Do not cover the light outlet at close range, as the energy radiated by the light may damage the product's light emitting components, and even cause external objects to burn. ·Non-standard batteries, do not take them out for charging. ·Please use the standard charging cable for charging. ·Do not touch the hot surface, or else it may cause skin burns. ·Don't leave the light in a car where the inside of temperature may be over 60¥, or in similar places. ·Do not use damaged or deformed batteries, or those with a broken casing. NOTICE ·DO NOT leave the light in any type of fabric bag or fusible plastic container under high temperature. ·Active thermal management: The built-in proximity sensor monitors temperature in real-time and suppresses overheating by reducing output. ·Please do not short-circuit the charging port with metal or a conductor, as it will cause battery drain. ·Do not disassemble the product. ·Do not immerse the flashlight in seawater or other corrosive media as it will damage the product. REMARK ·Before long term storage, please fully charge the product. ·Keep the charging port clean and dry. EXCLUSION CLAUSE Olight is not liable for damages or injuries sustained resulting from the usage of the product inconsistent with the warnings in the manual, including but not limited to using the product inconsistent with the recommended lockout mode. WARRANTY We provide a warranty for products that experience defects in material and workmanship under normal use. We will repair or replace the products depending on the specific situation. However, please note that the warranty does not cover loss, theft, deliberate damage, or cosmetic damage. For the complete warranty information, please visit Olightworld.com or your local Olight official website. USA Customer Support: cs@olightstore.com Australia Customer Support: contact@olightstore.com.au Germany Customer Support: kontakt@olightstore.de France Customer Support: cs@olightstore.fr UK Customer Support: contact@olightstore.uk Japan Customer Support: cs@olightstore.jp Canada Customer Support: cs@olightstore.ca Korea Customer Support: olightkorea@olightworld.com Austria Customer Support: kontakt@olightstore.at Italy Customer Support: contatto@olightstore.it Spain Customer Support: contacto@olightstore.es Thailand Customer Support: cs@olightstore.co.th China Customer Support: Wechat: olightcs For other countries and regions, please contact Global Customer Support: contact@olightworld.com Dongguan Olight E-Commerce Technology Co., Ltd. 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China. Made in China 3.4000.0710 CAN ICES-005 (B) / NMB-005 (B) A. 10, 31, 2023