Owner's Manual for DALI models including: DH8 DMX 8 Channel Relay Unit, DH8, DMX 8 Channel Relay Unit, Channel Relay Unit, Relay Unit
6 sept. 2023 — Three operating modes: DALI mode, DMX mode and manual mode. ○ LED segment display and 3 button operation. ○ Compliant DALI device type 7,. , in accordance.
DH8
DALI/DMX8-Channel Relay Unit
Three operating modes: DALI mode, DMX mode and manual mode. LED segment display and 3 button operation. Compliant DALI device type 7, DALI-2 certified, in accordance
with DALI standard protocol IEC 62386-101,102, 208 and in compliance with DALI products from other international incorporation. DALI address can be manually assigned and shown in digital display or automatically assigned by DALI master. Comply with the DMX512 standard protocols, support RDM function. Support manual switch. High-inrush specification relays (single pole, normally open). Zero cross switching function, 8 independently output channels. Can operate as: 8 individual channels (8 × 1) 4 sets of 2 channels (4 × 2) 2 sets of 4 channels (2 × 4)
DALI
LVD
DT7 / 8,4,2 DALI address / DMX-RDM / 8-channel dry contact output / Numeric display / Din Rail
Technical Parameters
Input and Output
Input voltage 100-240VAC
Input current
Full load loss power Input signal
Relay contacts
0.1A
Max. 12W
DALI and DMX512 High inrush (120 A at 20ms), single-pole, single-throw (SPST) relay.
Max relay load current
16A resistive load (incandescent lamp) 8A Capacitive load (LED dimming power supply) 8A inductive load ( uorescent lamp)
Environment Operationtem perature Case temperature (Max.) IP rating
Package Size Gross weight
Ta: -20 OC ~ +55OC Tc: +70 OC IP20
L165 x W98 x H72mm 0.422kg
Safety and EMC EMC standard (EMC) Safety standard(LVD) Certi cation
ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 62368-1:2020+A11:2020 CE,EMC,LVD
Warranty Warranty
5 years
Mechanical Structures and Installations
DALI signal input, no need distinguish plus-minus polarity
DMX signal input DMX signal output
AC input
LED indicator Digital display
DA1 DA2 DA1 DA2 GND D- D+ GND D- D+
DALI IN
DMX IN
DMX OUT
1 K1A K1B
2 K2A K2B
3 K3A K3B
4 K4A K4B
5 K5A K5B
PG N L 100-240VACIN
DH8
DALI/DMX 8-ChannelRelay Unit
Uin = 100-240VAC Iin = 0.1A Out = 8×16A Temp Range: -20~+55
DT7 IEC62386
6
7
8
K6A K6B
K7A K7B
K8A K8B
Setting button Installation rack
1# 2# 3# 4# 5# 6# 7# 8# Relay Relay Relay Relay Relay Relay Relay Relay
User Manual Ver 1.0.0 2023.7
DIN Rail Mounting Size: TS-35/7.5 or TS-35/15
Page 1
Wiring Diagram
DA 2 DALI DA 1
GND D- DMX D+
DA1 DA2 DA1 DA2 GND D- D+ GND D- D+
DALI IN
DMX IN
DMX OUT
PG N L 100-240VACIN
1 K1A K1B
2 K2A K2B
3 K3A K3B
4 K4A K4B
5 K5A K5B
6 K6A K6B
7 K7A K7B
8 K8A K8B
L N E
Operation
Work mode setting Short press M button to switch DALI mode, manual mode and DMX mode. DALI mode, display "dAxx" or "dUxx", xx is DALI address. Manual mode, display "Hxon" or "HxoF", x is 1-8 channel. DMX mode, display "Axxx", xxx is DMX start address.
DALI mode (dA00~dA63)
Manual mode (H1on~H8on)
DMX mode (A001~A512)
Channel setting Long press M and button for 2s, prepare for setup channel.This setting is valid for all three work modes. Short press or button to switch 8 independent channels("CH-8"), 4 groups of 2 channels("CH-4") or 2 groups of 4 channels("CH-2"). Short press M button or timeout 10s, quit channel setting.
DALI mode
Set start DALI Address via buttons: Display "dAxx", xx is start DALI address. Long press or button for 2s, prepare for setup DALI address. Short press or button to setup start DALI address. Short press M button or timeout 10s, quit DALI address setting.
DALI address assigned by DALI masters: DALI address can also be assigned by DALI Master controller automatically. Please refer to user manuals of compatible DALI Masters for speci c operations. The digital display will show "dAAU" When the DALI master is assigning address. After address is assigned, the digital display will show the start DALI address"dAxx", xx is from 00 to 63. Using the DALI master to assign addresses may result in discontinuous addresses, and the starting DALI address "dUxx" is displayed.
Manual mode Display "Hxon" or "HxoF", x is 1-8 channel, "on" is ON state, "oF" is OFF state. Short press button to switch channel. Short press button to switch ON/OFF state.
DMX mode Set start DMX Address via buttons: Display "Axxx", xxx is start DMX address. Long press or button for 2s, prepare for setup DMX address. Short press or button to setup start DMX address. Short press M button or timeout 10s, quit DMX address setting.
User Manual Ver 1.0.0 2023.7
Page 2
Corel PDF Engine Version 16.1.0.843