Logic 5.0 Commercial Door Operator

IMPORTANT INSTALLATION NOTE: THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED DOOR SYSTEMS TECHNICIAN ONLY. Operators are shipped in C2 operating mode. Visit www.liftmaster.com to locate a professional installing dealer in your area.

Warranty: 2 YEAR WARRANTY

Serial # _________________________ Installation Date _________________________

CONTACT INFORMATION

LiftMaster
300 Windsor Drive
Oak Brook, IL 60523
LiftMaster.com

INTRODUCTION

Congratulations on purchasing a quality LiftMaster Logic 5.0 Commercial Door Operator.

The Logic 5.0 operator provides everything you know and trust in the prior version, plus the new features listed below:

MyQ^® Technology

• Enables secure monitoring and control of the operator with a smartphone, tablet or computer (requires a LiftMaster Internet Gateway).

Security+ 2.0^®

• Increased security – with every click a new code is sent to the commercial door operator ensuring the door opens only for the individual pressing the remote.
• Enhanced radio communicates with tri-band frequency to improve range and reduce interference – assuring the door opens, stops and closes conveniently and reliably every time.

Dual Voltages

• Single phase operators provide (115V and 230V).
• 3 phase operators provide (208/230V and 460V).
• 575V operator.

CYCLE RATINGS

STANDARD DUTY:

Up to 25 cycles/hr. at peak periods.
Up to 80-90 cycles/day.

Models: T, APT, J, DJ, H, DHJ, & SD

HEAVY DUTY:

25 cycles/hr. constant high loading in excess of 90 cycles/day.

Models: GT, GH, & GSD

PROGRAMMING

INTRODUCTION TO PROGRAMMING

Many programmable functions require that a LiftMaster Entrapment Protection (LMEP) Device be installed in order to function.

Before programming the logic board, set the operator's open and close limits. LEDs on the logic board are provided to assist setting the limits. As each limit is activated the corresponding LED will light up. The abbreviations are Open Limit Switch (OLS), Close Limit Switch (CLS) and Sensing Limit Switch (SLS).

When power is applied to the operator, the following LED's will illuminate: STOP, CLOSE, OPEN, LMEP, 24Vac, RADIO, DATA, TIMER ENABLE, OLS MID, SLS, CLS, and MAS. Once the power up process is completed (approximately 2-3 seconds) only the appropriate LED’s will continue to be lit (i.e., STOP, 24Vdc, limit LED(s) if limit(s) is activated).

NOTE: When the power up process is over, the MAS LED will blink a code indicating the version of firmware. If the selector dial is in the DIAG, OPTN, or PROG position, the MAS will not provide this code. After the code has been provided the MAS LED will go out.

LOGIC BOARD PUSH BUTTONS (OPEN, CLOSE, STOP)

Open, Close and Stop buttons are mounted directly on the logic board. Thus, making it easy to program as well as having the door control at the electrical box.

Either the stop control or a jumper MUST be wired between terminals 4 and 5 for the push buttons to function.

LOGIC BOARD OVERVIEW

• Optional Auxiliary Card Receptacles
• Current Sense (3 Phase ONLY)
• Motor Direction Jumper
• Maximum Run Timer Button
• Coaxial Antenna Connector
• Radio Learn Button
• Mid-Stop Learn Button
• Timer-To-Close Learn Button
• System Wiring Connector (J3)
• Selector Dial (used for programming and selecting wiring type)

Components on Logic Board:

• Control Wiring Terminal Block (Terminals 1-14)
• 24VAC POWER
• 24VAC
• TIMER DEFEAT
• OLS
• MID
• 3-PHASE
• 1-PHASE
• COMMON
• MAS
• SLS
• LMEP:
• MRT MID TTC TIMER ENABLE EDGE:
• OPEN Button
• CLOSE Button
• STOP Button
• RADIO Button
• T, TS, E2, FSTS, D1, DIAG, C2, OPTN, PROG (Selector Dial positions)
• RELAY A, RELAY B
• SBC
• Single Phase & Three Phase Jumper
• Maintenance Alert System Button for Programming
• Main Motor Control Harness Connection

DETERMINE AND SET WIRING TYPE

Read the descriptions of the different wiring types to determine which setting will be correct for each application. Once the wiring type is determined, set the selector dial accordingly.

LIFTMASTER MONITORED ENTRAPMENT PROTECTION (LMEP) DEVICE IS REQUIRED

A LiftMaster Entrapment Protection (LMEP) Device is required for the following wiring types:

• B2: Momentary contact to open, close and stop, plus wiring for sensing device to reverse and auxiliary devices to open and close with open override. Programmable mid stop available with this wiring type. Compatible with 3-Button Station, 1-Button Station, 1 and 3-Button Remote Control.

TS (TIMER SECURE)

This mode will attempt to close the door from any position except when fully closed, or when a safety input is present. The stop button will not disable the Timer-To-Close at any position. To disable the Timer-To-Close in this mode, installation of a defeat switch is required (see wiring diagram on the inside cover of operator).

Momentary contact to open, close, and stop with open override and Timer-To-Close. Every device that causes door to open, including a reversing device, activates the Timer-To-Close. Auxiliary controls can be connected to open input to activate the Timer-To-Close. If the timer has been activated, the open button and radio control can recycle the timer. The Timer-To-Close will function from the programmable mid stop with this wiring type. Compatible with 3-Button Station, 1-Button Station and 1 and 3-Button Remote Control.

NOTE: A Programmable “Car Dealer Mode” available.

T

Momentary contact to open, close, and stop, with open override and Timer-To-Close. Every device that causes the door to open, except any sensing edge input device, activates the Timer-To-Close. Auxiliary controls can be connected to open input to activate the Timer-To-Close. If the Timer-To-Close has been activated, the open button and radio control can recycle the timer. The stop button will deactivate the timer until the next command input. The Timer-To-Close will function from the programmable mid stop with this wiring type. Compatible with 3-Button Station, 1-Button Station and 1 and 3-Button Remote Control.

NOTE: Programmable “Car Dealer Mode” available.

FSTS

Momentary button contact for open, close and stop programming. User set mid stop. User set Timer-To-Close. The single button station opens the door to the full open limit bypassing the mid stop and activates the Timer-To-Close, putting the operator in TS mode until the door reaches the down limit, or is stopped in travel. At which time the operator enters the B2 mode.

Compatible with 3-Button Station, 1-Button Station, 1 and 3-Button Remote Control. A 1-Button remote control in FSTS mode will open only with the Timer-To-Close, bypassing a programmed mid stop. The Timer-To-Close will reset and reverse when closing.

LIFTMASTER MONITORED ENTRAPMENT PROTECTION (LMEP) DEVICE IS RECOMMENDED

A LiftMaster Entrapment Protection (LMEP) Device is recommended for the following wiring types:

• C2: Momentary contact to open and stop with constant pressure to close, open override plus wiring for sensing device to reverse. Programmable mid stop available with this wiring type. Compatible with 3-Button Station and 1-Button Station.
• E2: Momentary contact to open with override and constant pressure to close. Release of close button will cause door to reverse (roll-back feature) plus wiring for sensing device to reverse. Compatible with 3-Button Station.
• D1: Constant pressure to open and close with wiring for sensing device to stop. Compatible with 2 or 3-Button Station.

SELECTOR DIAL

Diagram showing Selector Dial positions (T, TS, E2, FSTS, D1, DIAG, C2, OPTN, PROG).

IMPORTANT NOTES:

1. External interlocks may be used with all functional modes.
2. Auxiliary devices are any devices that have only dry contacts. Examples: loop detector, pneumatic or electrical treadles, radio controls, one button stations, pull cords, etc.
3. Open override means that the door may be reversed while closing by activating an opening device without the need to use the stop button first.
4. When the door is in a stopped position other than fully closed, and an LMEP or EDGE input is activated, the Restricted Close (RC) feature will allow a close command when the close button is pressed and held. The operator will begin closing after 5 seconds. If the close button is released the door will stop. When in E2 mode, the door will move to the fully open position.

PROGRAMMING

REMOTE CONTROLS

WARNING: To prevent possible SEVERE INJURY or DEATH:

• Install a LiftMaster Monitored Entrapment Protection (LMEP) Device.
• NEVER permit children to operate or play with door control push buttons or remote controls.
• Activate door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
• ALWAYS keep door in sight until completely closed. NEVER permit anyone to cross the path of closing door.

Built-in 3-channel, Security+ 2.0^® radio receiver allows you to add up to 90 remote control devices and up to 30 keyless entry devices.

NOTE: The following programming requires a LiftMaster Monitored Entrapment Protection (LMEP) Device.

SINGLE BUTTON REMOTE CONTROL

1. Press and release the RADIO button (RADIO LED will light).
2. Press and hold the remote control button until the RADIO LED flashes rapidly, then release remote control button. The RADIO LED will then remain on solid after releasing the button. Repeat to add additional remote control(s).
3. Press and release the RADIO button to complete the programming. The programming mode is exited if no activity is performed within 30 seconds.

3-BUTTON REMOTE CONTROL TO OPERATE AS A WIRELESS 3-BUTTON CONTROL STATION

NOTE: The feature will use 3 of the 90 memory channels in the operator.

1. Press and release the RADIO button on the logic board (the Radio LED will light).
2. Press and release the desired button on the logic board (OPEN, CLOSE or STOP). The Radio LED will flash and then stay on solid.
3. Press and hold the desired button of the remote control until Radio LED flashes rapidly, then release.
4. Press and release the RADIO button to complete the programming. The programming mode is exited if no activity is performed within 30 seconds.

Repeat steps 1 through 4 to program additional buttons.

TO ERASE ALL REMOTE CONTROLS

1. Press and hold the RADIO button on the logic board until the RADIO LED flashes rapidly (approximately 5 seconds). All remote controls will be erased.

NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this transceiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003. This device must be installed in a way where a minimum 8" (20 cm) distance is maintained between users/bystanders and device.

MyQ^® SETUP (OPTIONAL)

For Smartphone App, tablet or PC control, LiftMaster MyQ Internet Gateway (model 828LM) is required.

1. To enter programming mode, press and release the RADIO button on the logic board (the RADIO LED will light).
2. To program the MyQ device, place the MyQ device into learn mode (see instructions for the specific MyQ device).
3. When the programming is complete the RADIO LED will turn off.

NOTE: If the programming is not completed within 3 minutes, the program mode will be exited and the RADIO LED will turn off.

TO ERASE ALL MYQ DEVICES:

1. Press and release the RADIO button on the logic board (the RADIO LED will light).
2. Press and hold the MAS button for 5 seconds. The RADIO LED will flash for approximately 5 seconds and the RADIO LED will turn off.

All MyQ devices are now erased.

Please visit LiftMaster.com/MyQ-CDO for troubleshooting information.

TIMER-TO-CLOSE

WARNING: To prevent possible SEVERE INJURY or DEATH:

• Install a LiftMaster Monitored Entrapment Protection (LMEP) Device.
• NEVER permit children to operate or play with door control push buttons or remote controls.
• Activate door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
• ALWAYS keep door in sight until completely closed. NEVER permit anyone to cross path of closing door.

Feature: Timer automatically closes the door after preset time. All entrapment protection devices must be unobstructed.

Benefit: The door will automatically close after the preset amount of time. Great for apartment buildings, fire stations and other applications where the end user wants the door to close automatically after a specified amount of time.

Requirements: Must have at least one LiftMaster Monitored Entrapment Protection (LMEP) Device installed (refer to installation manual). Wiring type must be set to TS, T or FSTS.

TO PROGRAM MANUALLY (METHOD 1):

1. Close the door.
2. Turn the selector dial to PROG.
3. Press and release the TIMER button on the logic board.
4. Press and release the STOP button to clear the timer.
5. Press and release the OPEN button for every second the operator should wait before attempting to close the door. Press and release the CLOSE button for every 15 seconds the operator should wait before closing the door.
6. Press and release the TIMER button to complete programming. The OPEN/CLOSE button LEDs will flash to confirm the timer setting. The OPEN LED will flash once for every second programmed and the CLOSE LED will flash once for every 15 seconds programmed.
7. Turn the selector dial to desired timer wiring type (TS, T or FSTS).

Example: To close the door after 70 seconds. Turn selector dial to PROG, press and release the TIMER button, press and release the STOP button to clear the timer, press and release the CLOSE button four times for 60 seconds and press and release the OPEN button 10 times for 10 seconds. Press the TIMER button to finish programming the timer. Turn the selector dial to desired timer wiring type (TS, T, or FSTS).

PROGRAM TIMER-TO-CLOSE BY EXAMPLE (METHOD 2):

TO PROGRAM:

1. Close the door.
2. Turn the selector dial to PROG.
3. Press and hold TIMER button for 5 seconds until OPEN and OLS flashes then release.
4. Press and release the OPEN button and wait for the door to reach full open or mid stop position.
5. Wait for desired amount of time to pass. (An internal stop watch starts counting when the door stops moving.)
6. Press and release the TIMER button, CLOSE button or STOP button to stop the timer. (TIMER SET LED will turn on.)
7. Turn the selector dial to the desired wiring type (T, TS, FSTS).

NOTE: To read back the Timer-To-Close setting, turn the selector dial to DIAG and press the TIMER button. The OPEN LED will flash once for every second programmed and the CLOSE LED will flash once for every 15 seconds programmed.

In T Mode, timer can be deactivated from the open position by pressing the STOP button. The timer will be reactivated on the next operation command. The STOP button WILL NOT deactivate the timer in the TS mode. To deactivate the timer for more than one cycle in T mode or in TS mode, attach a defeat switch to 11 and 12 (COMMON and TIMER DEFEAT).

Selector Dial diagrams are shown for reference.

MANUAL RELEASE

WARNING: To prevent possible SERIOUS INJURY or DEATH from a falling door or arm:

• DO NOT stand under the door arm when pulling the emergency release.
• If possible, use emergency release handle to disengage trolley ONLY when door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.
• NEVER use emergency release handle unless doorway is clear of persons and obstructions.

EMERGENCY DISCONNECT SYSTEM MODEL GT AND T

TO DISCONNECT DOOR FROM OPERATOR

The door should be in the fully closed position if possible.

1. Pull emergency release handle straight down. Emergency disconnect will open. ➡️

TO RECONNECT DOOR ARM TO TROLLEY

1. Lift free end of door arm to trolley. Pull emergency release handle to allow arm to engage roll pin. Release handle. Emergency disconnect will close.

NOTICE

EMERGENCY DISCONNECT SYSTEM MODEL APT

TO DISCONNECT DOOR FROM OPERATOR

The door should be in the fully closed position if possible.

1. Pull down on the emergency release handle and raise or lower the door manually.

TO RECONNECT DOOR ARM TO TROLLEY

1. The trolley will reconnect on the next UP or DOWN operation, either manually or by using the door control or remote.

NOTICE

EMERGENCY DISCONNECT SYSTEM MODEL H, GH, J, AND HJ

This operator has provisions for manually operating the door in case of emergency or power failure. Refer to the appropriate instructions below for your model operator.

MODEL H AND GH

These operators are equipped with a manual hoist. An electrical interlock will disable the electrical controls when the hoist is used. To operate the hoist:

1. Pull the disconnect chain (sash chain) ⛓️ to engage the hoist mechanism. The disconnect chain may be locked in position by slipping the end through the keyhole of the chain keeper mounted on the wall.
2. Operate the door in the desired direction by pulling on one side or the other of the continuous loop hoist chain.
3. The disconnect chain must be released from the chain keeper before the door will operate again electrically.

MODEL J

This operator has a floor level disconnect chain to disconnect the door from the door operator.

1. To disengage, pull the disconnect chain (sash chain) and secure in the disengaged position by slipping the end through the keyhole bracket mounted on the wall.
2. The door may now be pushed up or pulled down manually.
3. Release the disconnect chain to operate the door again electrically.

MODEL HJ

This operator includes both a floor level disconnect chain (sash chain) to disconnect the door from the door operator and a disconnect chain with manual hoist to electrically disable the operator controls.

1. Pull the disconnect chain to engage the hoist mechanism. The disconnect chain may be locked in position by slipping the end through the keyhole of the chain keeper mounted on the wall.
2. To disengage, pull the disconnect chain and secure in the disengaged position by slipping the end through the keyhole bracket mounted on the wall.
3. Operate the door in the desired direction by pulling on one side or the other of the continuous loop hoist chain.
4. Release the disconnect chain to operate the door again electrically.

CAUTION: To prevent possible SERIOUS INJURY from a moving chain:

• DISCONNECT electric power to the operator BEFORE manually operating your door.
• If possible, use emergency disconnect ONLY when door is CLOSED. Weak or broken springs or unbalanced door could result in an open door falling rapidly and/or unexpectedly.
• NEVER use emergency disconnect unless doorway is clear of persons and obstructions.

TESTING

Apply power to the operator.

When power is applied to the operator, the following LED's will illuminate: STOP, CLOSE, OPEN, LMEP, 24Vac, RADIO, DATA, TIMER ENABLE, OLS MID, SLS, CLS, and MAS. Once the power up process is completed (approximately 2-3 seconds) only the appropriate LED's will continue to be lit:

• Between limits: 24Vac and STOP
• Fully closed position: 24Vac, STOP, CLS and SLS
• Fully opened position: 24Vac, STOP and OLS

Additional LED's will light when device(s) are activated.

NOTE: When the power up process is over, the MAS LED will blink a code indicating the version of firmware. If the selector dial is in the DIAG, OPTN, or PROG position, the MAS will not provide this code. After the code has been provided the MAS LED will go out.

TEST THE PHOTOELECTRIC SENSORS

1. Open the door.
2. Place an obstruction in the path of the photoelectric sensors. The LMEP LED will blink on the logic board.
3. Press and hold the CLOSE button. The door should not close.
4. Remove the obstruction.
5. Press and hold the CLOSE button. Door should close.

If the LMEP is activated while closing the door should reverse.

IMPORTANT NOTES:

• Be sure you have read and understand all safety instructions included in this manual.
• Be sure the owner or person(s) responsible for operation of the door have read and understand the safety instructions, know how to electrically operate the door in a safe manner and how to manually disconnect the door from the operator.

WARNING: To avoid SERIOUS personal INJURY or DEATH:

• Disconnect electric power BEFORE performing ANY adjustments or maintenance.
• ALL maintenance MUST be performed by a trained door systems technician.

TEST 3-BUTTON CONTROL STATION

1. Press OPEN button. (The door should move in the open direction.)
2. Press STOP button. (The door should stop.)
3. Press and hold the CLOSE button. (The door should move in the close direction.)
4. Release CLOSE button. Door should stop if in C2 or D1 mode. Door will reverse to full open position in E2 mode. The door should continue closing in all other modes.
5. Press STOP button. (The door should stop.)

TEST LIMIT ADJUSTMENT

1. Press OPEN button. (The door should open.)
2. Allow the door to fully open.
3. Press and hold the CLOSE button. (The door should close.)
4. Allow the door to fully close.
5. If the limits are not set properly, remove power and adjust limits (refer to Limit Adjustment section).

TROUBLESHOOTING

To locate a dealer in your area visit us online at www.liftmaster.com.

MAINTENANCE SCHEDULE

WARNING: To avoid SERIOUS personal INJURY or DEATH:

• Disconnect electric power BEFORE performing ANY adjustments or maintenance.
• ALL maintenance MUST be performed by a trained door systems technician.

Every 3 months or 5,000 cycles repeat all tests in the Testing section. Call a trained door systems technician. To locate a dealer in your area visit us online at www.liftmaster.com.

The operator should be serviced at the following intervals:

• Every 3 months or 5,000 cycles
• Every 6 months or 10,000 cycles
• Every 12 months or 20,000 cycles

ACCESSORIES

ENTRAPMENT PROTECTION DEVICES

MONITORED

• CPS-U: Dual-Sided Infrared Photo Eyes. NEMA 1 enclosure. Range: 30 ft (9.1 m).
• CPS-UN4: Monitored Thru-Beam Photo Eyes. Heavy-duty, NEMA 4 enclosure. Range: 45 ft (13.7 m).
• CPS-RPEN4: Monitored Retro-Reflective Photo Eyes. Polarized reflector, NEMA 4X enclosure. Range: 50 ft (15 m).
• CPS-OPEN4: Monitored Dual-Sided Photo Eyes. Flexible housings, NEMA 4X enclosure. Range: 45 ft (13.7 m).

MONITORED INTERFACE CARDS

• CPS3CARD: Safety Interface Card. Enables use of a second set of monitored photo eyes or edge.
• CPS-MEI: Edge Interface 2-Wire Monitored. For use with approved 2-wire edges.
• CPS-EI: Edge Interface 4-Wire Monitored. For use with approved 4-wire edges.

OPTICAL EDGE SYSTEM (OES)

• OES-SD16: Sectional 2-Wire Door Edge Kit (16 ft / 4.9 m). Includes sensors, rubber edge, mounting hardware.
• OES-SD24: Sectional 2-Wire Door Edge Kit (24 ft / 7.3 m). Includes sensors, rubber edge, mounting hardware.
• OES-RD16: Rolling 2-Wire Door Edge Kit (16 ft / 4.9 m). Includes sensors, rubber edge, mounting hardware.

OES Features: Durable rubber edge, cut-to-length, NEMA 6 rating, infrared optical sensors, max range 33 ft (10 m). Available in 50 ft (15 m) bulk rolls.

NON-MONITORED VEHICLE DETECTION SYSTEM

• 65-8202: Pneumatic Sensing Edge Kit with air switch, 2-wire coil cord, 14 ft (4.3 m) air hose.
• 65-5202: Pneumatic Sensing Edge Kit with air switch, 2-wire take-up reel (20 ft / 6 m extended), 14 ft (4.3 m) air hose.

ACCESSORIES

MyQ^® ACCESSORIES

• 828LM: LiftMaster^® Internet Gateway. Enables remote control of doors and lights via smartphone/tablet.
• 829LM: Garage and Gate Monitor. Monitors status of up to 4 MyQ^® compatible openers/gate operators.
• 825LM: Remote Light Control. Automatically controls lights using opener, remote, or Internet Gateway. Plugs into outlet.

REMOTE CONTROLS WITH SECURITY+ 2.0^® & CONNECTIVITY

• 811LM: Encrypted DIP Switch Single-Button Remote Control. Ideal for common spaces requiring many remotes.
• 813LM: Encrypted DIP Switch Three-Button Remote Control. Includes Red, Yellow, Green markings for Open, Close, Stop.
• 877LM: Wireless Keypad. Programmable with temporary access codes.

RADIO

• STAR1000: Commercial Access Control Receiver. Programs up to 1000 LiftMaster^® remotes. Supports suspending/unsuspending access.

CONTROL STATIONS

• 02-101: 1-Button Control Station (Steel enclosure).
• 02-102: 2-Button Control Station (Steel enclosure).
• 02-103L: 3-Button Control Station (Steel enclosure with Maintenance Alert System).
• 02-110: Key Control Station (NEMA 1, flush mount, with Stop button).
• 02-401: 1-Button Indoor Surface Mount Station (NEMA 1). Activates one or more commercial doors.

ACCESSORIES

MOUNTING BRACKETS

• 10-12360: Heavy gauge steel bracket for vertical/horizontal mount on front/top of coil. Compatible with many OEM manufacturers. For J, H, DJ, DH operators. May be welded.
• 08-9098: Cast iron bracket for side mount operators (J, H, DH, DJ, GH) on end bracket. For vertical/horizontal mount. Cannot be welded.
• 08-9098EZ: Same as 08-9098, with adapter plate for easier mounting.
• 1A4324: Heavy gauge steel bracket for vertical/horizontal mount on front/top of coil. For J, H, DJ, DH operators. May be welded.
• 1A4324EZ: Same as 1A4324, with adapter plate for easier mounting.

CHAIN TENSIONERS (For Jackshaft Type Operators)

• 71-6023: For 1" (2.5 cm) shafts. Recommended for proper drive chain tension.
• 71-6125: For 1-1/4" (3.2 cm) shafts.

OPTION CARDS

• TLS1CARD: Timer Light Status Card. Provides special functions for auxiliary devices (lights, bells, horns/strobes) and special timer functions.
• AUXCARD: Auxiliary Contact Card. Provides Normally-Open and Normally-Closed contacts for door status (idle, opening, closing).

ADDITIONAL CONTROL ACCESSORIES

• 86LM (15' [4.6 m]), 86LMT (25' [7.6 m]): Antenna Extension Kit. Used with EXT-ANT for maximum radio receiver range.
• RGL24LY: Red/Green Traffic Light. Indicates when a commercial door reaches the open position for safe entry/exit. (TLS1CARD recommended).
• 50-HERK2: Motion Detector 24V. Microwave motion detector with two programmable channels.
• 50450: Switch Sectional Door Interlock. NEMA 4 switch disables operator control circuit when door is locked, preventing electrical operation.