IN-12 Nixie Desktop Clock

Welcome

Thank you for purchasing a nixieshop.com clock! Please read the following manual carefully to ensure you get the most out of your Nixie Clock.

Unboxing

All nixieshop.com clocks are shipped as carefully as possible to ensure safe delivery. In the unlikely event that the clock arrives damaged, or if you have any questions about using the product, please contact us at petro.vodopyan@gmail.com.

Carefully remove the clock from the box when unboxing this product. The clock unit is protected with a plastic cover to secure tubes during shipping. The Nixie tubes are installed into sockets and should be handled with care.

WARNING: Please note that this clock is for indoor use only.

Contents

Each package contains the following items:

1. Clock base with mounted Nixie tubes (tube types are specific to purchased model).
2. 12V 1A power adapter with 5.5mm X 2.1mm jack.
3. IR remote control.
4. Built-in motion sensor module (based on Doppler radar).
5. Product manual.

Warranty

Nixieshop.com values your business and always attempts to provide the very best quality of service. We provide a lifetime warranty for electronics and a two-year warranty for tubes. The warranty applies only to products manufactured by Nixie Shop.

The warranty covers burned-out tubes (up to three) and problems with the electronics of the clock. The warranty does not cover:

• 12V external power supply.
• Damage resulting from negligence.
• Damage resulting from unauthorized modification of the product.
• Damage caused by natural disaster.
• Theft or loss of the product.

Powering Up

On the rear panel of the clock, there is a power socket. Plugging in and turning on the power, the clock will perform a brief self-test to confirm it is operational. The digits on the clock will scroll through from 0-9, then the clock will beep once.

Sleep Mode

Setting the clock to sleep when not required can help prolong the life of the Nixie tubes and save power. The sleep feature works using 24-hour time values. For best results, the clock should also be set into 24H mode (menu option 12). To disable the sleep feature, set the start value equal to the end value.

Settings and Adjustments

There are two ways to adjust the various settings of the clock:

1. The knob on the front side of the clock. Pressing it once changes through the menu items; twisting it changes the values.
2. Using the IR remote control. The "OK" button acts as a menu button and changes the current menu setting. Pressing the up/right arrows increases the current value, and down/left arrows decrease the values. The 0-9 buttons change the color scheme of RGB lights. The "*" acts as the OFF button, and the "#" button switches the clock ON.

Feedback

If you don't mind, please give us positive feedback at our Trustpilot profile or visit our Facebook group and leave a comment. Your feedback will help us develop the project and is always appreciated and welcome.

Find Us on Social Networks

• YouTube
• Facebook
• Instagram

Menu

The menu items are listed below in the order they will appear when navigating through them. Once you click the menu button, the clock will switch into edit mode – it will display the setting number (SN) in the leading position and the current setting value (SV) on the last two numbers, which will be blinking.

LED RGB Values

The clock has one RGB LED under each Nixie tube. All colors are adjustable and can be set to a custom brightness.

1. Red color brightness (0 - 40 levels).
2. Green color brightness (0 - 40 levels).
3. Blue color brightness (0 - 40 levels).

Alarm Settings

1. Alarm mode: 1 - enable; 0 - disable.
2. Alarm start hour.
3. Alarm start minute.

WARNING: The clock will make a short beep sound once it reaches the alarm time. To stop the alarm, rotate the knob.

General Settings

1. Colon tube modes: 0 - blinks once a second (default); 1 - permanently ON; 2 - permanently OFF; 3 - sensor status (sensor testing mode see #23, ON when detects motion).
2. Beep once per hour, on the hour: 0 - disable (default); 1 - enable.
3. Slot machine frequency (1 – 5): Value is the interval in minutes. 0 - disable.
4. Spin changing numbers mode: 0 - classic; 1 - scroll changing numbers; 2 - wave scrolling.
5. Animate RGB LED lights: 0 - none; 1 - linear; 2 - random.

Time/Date Settings

1. 12/24 hour mode: 0 - 24h mode (default); 1 - 12h mode.
2. Set hours.
3. Set minutes.
4. Set seconds.
5. Set month.
6. Set day.
7. Set year.

Sleep Settings

1. Set sleep starting hour - the clock displays ZZ:XX:YY (where XX is the value of the sleep start hour).
2. Set sleep ending hour - the clock displays ZZ:XX:YY (where YY is the value of the sleep end hour).
3. Display date at the end of period defined in setting #10: 1 - enable; 0 - disable.
4. Timeout for motion sensor (options from 1-5) - sets delay time from ~1 minute and longer.
5. Activates built-in motion sensor (for versions 1.14 and later): 0 - disable (default); 1 - enable. Motion sensor also overrides the sleep timer (if activated).
6. Silent mode: 0 - disable; 1 - enable. Switches on/off buzzer.
7. Internal temperature in Celsius.
8. Firmware version.