User Manual for INMOTION models including: V13 Pro, Challenger Electric Unicycle, Challenger, Electric Unicycle, Unicycle
INMOTION Challenger Pro Electric Unicycle | 56 MPH & 10000W Peak Power – INMOTION EU
Monocycle électrique INMOTION Challenger Pro | 56 MPH et puissance de crête de 10 000 W – INMOTION EU
INMOTION V13 Pro Electric Unicycle | World's Fastest EUC - INMOTION
File Info : application/pdf, 12 Pages, 3.74MB
DocumentDocumentV13 Challenger Electric Unicycle User Manual Please wear an approved helmet, elbow pads, knee pads and other protective gear before riding. Please read the user manual and keep it for ready reference. 1. About This Manual This manual applies to the electric unicycle Challenger V13 (hereinafter referred to as V13) produced by INMOTION Technologies Co.,Ltd. V13 is an intelligent, high-tech recreation product . When you use V13, there may be injuries caused by collision or falls and other risks. To reduce the possible risks and ensure the personal and property safety of you and others, please read this manual carefully and fully understand all warnings and precautions listed in it, then make sure you use it correctly. For the latest features/functions and safety guidance, please download from INMOTION official website. 2. Brief Introductions 2.1 Serial Number Serial number (hereinafter referred to as SN) is a unique identifier assigned sequentially to an item which can be used for warranty, maintenance, insurance compensation, damage confirmation, etc. SN is a 16-character number that can be found from the packing case sticker, user manual, vehicle body, and vehicle information on INMOTION App. 2.2 Packing List Before use, please read this user manual carefully and check to confirm that any and all parts are in serviceable condition. If any parts are missing, please contact your dealer immediately. User Manual Quick Start Guide Power Adapter Damper Regulator Kickstand Inflator Hex Socket M3 M4 M5 M6 Wrench*4 Power Pads Warning: Please retain the box at least 30 days after the date you receive your product for future use when transporting the electric unicycle. 1 3. Diagram Lock Catch Dashboard Power Button Headlight Front Bumper Trolley Anti-Spin Button Charging Port Taillight Tail Bumper Rear Mudguard Pedals Tire 4. Functions Power on/off: Long press the power button to turn on the wheel. Long press the power button to turn off the wheel after powering on. Headlight: Press the power button to turn on/off the light after powering on; The headlight can be set to automatically on/off on the App. Taillight: It flashes brightly when braking; The taillight keeps lighting up when the headlight is on. Anti-spin button: Press and hold the anti-spin button, the vehicle could result in loss of balance. Power Assistant : Turn on this mode to help you accelerate and brake rapidly. Acceleration Assistant: Adjust the values for better and rapid acceleration with smaller values representing shorter braking distance. Brake Assistant: Adjust the values for better and rapid acceleration with greater values representing shorter braking distance. Speed Description: For your safety,the vehicle's maximum speed will be limited to 60km/h after activation. When the total mileage of the vehicle exceeds 30km, you can remove this restriction in the APP, and then the maximum speed limit of the vehicle can be adjusted to 90km/h. 2 Charging The original charger is 126V 5A. Blue light indicates the Power is on, green light shows when the battery is fully charged, and red light indicates it's charging or completion of charge. Two chargers working together will reduce charging time by 50%; Type-C and USB ports are available for power output. Type-C USB Open Trolley Unfold: Pull up the lock catch, the trolley will bounce up automatically. Fold: Pull up the lock catch, then press down the trolley. 2 Charger 1 Charger 2 Suspension The air suspension systems must be inflated when you use them for the first time. Dashboard Get real-time riding information and set vehicle parameters after entering the password. 731mm 790mm Before Air Springs Inflation After Air Springs Inflation 3 5. Specifications Specification Basic specs Requirement to Rider Performance Battery Motor Charger Other Items Model Dimension Net weight Max. palyload Required height Recommended age Typical range [1] Max. slope [2] Max. speed [3] IP rating Charging time Working Temperature Storage Temperature Intelligent BMS Rating Voltage (VDC) Capacity Nominal power Max.of power Input Voltage (VAC) Output Voltage (VDC) Display Output ports Tire size Parameter V13Pro 579x268x731mm Approx. 53.2kg 130kg 120-200cm 16-50 years Approx. 95-150km Approx. 45° 90km/h IP55 Approx. 6h -10 ~ 45° C -20 ~ 45° C Over-charge, Over-temperature, Over-discharge, Over-current, Short circuit, Over-voltage 126V 3024Wh 4500W 10000W AC100-240V 50/60HZ 126V 5A 2.4 Inch touch-screen USB+Type-C 22 Inch air-filled low rolling resistance tire Tire pressure is 40Psi or 2.8Bar [1]: Typical range is obtained at full charge, with a load of 90kg, ambient temperature of 25° C, and riding at speeds of 20 to 40 km/h on a flat, paved road. The range of the wheel is influenced by factors such as temperature, tire pressure, road conditions, and riding habits (such as rapid acceleration and braking). [2]: fully charged, 90 kg payload, 25° C, no wind, at the flat road. [3]: fully charged, 90 kg rider get the data through a large amount of tests. 4 6. Dimension 731mm 268mm 490mm 790mm 579mm 579mm 579mm 7. Initial Use 7.1 Before Use V13 is a high-tech recreation product. When you ride without following the operation specifications, it may lead to unpredictable injuries and property losses. The following will explain how to use V13 and the precautions in details. Please read it carefully and use V13 as required. Before using, please make sure that all parts of V13 are not damaged and installed properly. Note: · Before using the V13, ensure that the battery is fully charged. It is recommended to charge it more than 80 percent of capacity. · Find a relatively open and flat area to practice riding, (at least 4m by 4m in area), both inside and outside. You need to be fully aware of the riding environment around you to ensure that you are not disturbed by obstacles such as cars, pedestrians, pets, bicycles, etc. · You need a skilled assistant stood by. The assistant must be familiar with V13 and all precautions and usage methods in this manual. · Please do not ride the vehicle on slippery ground. · Users are advised to wear comfortable, casual or sports clothing, and to wear flats and warm up to improve your flexibility. · Be sure to wear a helmet and riding protective gear to avoid injury. 5 7.2 Download INMOTION APP Download the App in the following ways 1. Scan the QR code below 2. Search "INMOTION" in the Apple store or Google Play Store. 3. Visit www.inmotionworld.com/support/app Note: V13 supports Bluetooth 5.0 BLE. The BLE ID is V13-XXXXXXXX, where XXXXXXXX is the last 8 digits of SN. Install the INMOTION App on your mobile device (iOS 8.0 and above or Android 4.4 and above supported) and follow the prompts to connect your V13. For more functions, please visit the official website to download the latest version of INMOTION App user manual. 7.3 Air Springs Please inflate the built-in air spring before using this product, otherwise it may damage the product. After powering off, lay the vehicle flat for 10 min and then inflate it as shown in the picture. Before inflating, unscrew the red covers of the air springs at the bottom of the pedals, and then use the inflator delivered with the vehicle to inflate, refer to the table below for air pressure. It is recommended to check the air pressure every 3 months. Weight - Barometer Weight Under 60kg 60-70kg 70-80kg 80-90kg 90-100kg 100-130kg Air pressure 80-120psi 120-130psi 130-150psi 150-180psi 180-200psi 200-220psi Scan to check out the how-to video 6 7.4 Damping Adjustment For initial use, user can adjust the damper according to weight and preference as follows 1.Open the protective cover. 2. Take out the damping regulator from accessories, insert it into the damping adjusting port in the direction shown in the figure, turn the regulator, the damping decreases counterclockwise, and increases vice versa. 3. After adjustment, cover it tightly. 7.5 Suspension Adjustment There will be a certain gap when the shock absorbing parts are used for a long time. When the riding experience is affected, use the M3 wrench delivered with the vehicle to adjust it. Reduce the gap by turning the M3 wrench clockwise, on the contrary, it increases. Adjustment port 7 Scan to check out the how-to video 7.6 Remove Air Suspensions and Dampers Scan to check out the how-to video How to Remove the Air Spring and Damper How to Install the Air Spring and Damper 8 7.7 Learning to Ride 1. Step on the pedal with one foot, then swing back and forth. 2. Step on the pedal with one foot, keep your feet and body upright and gradually shift your weight up. 3. Step on the pedal with one foot, lift the other foot off the ground for 1-2 seconds and start gliding. 4. Step on the pedal with one foot, push back with the other foot and start gliding. 5. Step on pedals with both feet, use your weight to move forward and back 9 6. Press the pedals with feet by different force to make a turn. INMOTION App Facebook Group Version: V1.0 Customer service center:service@imscv.com Website