深圳市铂胜光电有限公司
Owner's Manual for BERSN models including: Vesta-W4, Vesta-W4 LED Driver, LED Driver, Driver
Bridgelux, lnc. 20BS-U405W LED Driver 2BF24-20BS-U405W 2BF2420BSU405W 20bs u405w
File Info : application/pdf, 4 Pages, 619.20KB
DocumentDocumentVesta-W4 LED Driver 20W 250-500mA DIP 40V WiZ RGBTW 120-277V CC 4-Channels RGBW LED Bridgelux Vesta-W4 LED Driver connected by WiZ PRO can work with Bridgelux RGBW LED to enable colors and tunable white control features. It enables simple, cost effective wireless lighting system for energy saving and comfort. Advanced design of the smart LED driver helps to build a reliable and standardized connected lighting system with different functionalities from simple wireless dimming to cloud based operations Features · Easy wireless dimming and scheduling for energy saving and convenience · No gateway needed · Energy metering feature with 10% accuracy · Wi-Fi dual protocol module which enable local messages for installation and connectivity to WiZ cloud over Wi-Fi network · Future-proof flexibility, support OTA (Over-The-Air) firmware update · Protective features (short-circuit, open-circuit, over-load, no-load) · Reliable, flicker-free · 5 years warranty. Applications · Bridgelux RGBW Solution 1 /3 www.bersn.com Jan 2024 Electrical Data Item Model No. Rated Power Output Channels Output Current (4CH) Output Voltage (4CH) Nominal Input Voltage Nominal Input Current Max Input Current Nominal Input Frequency Power Factor Eff (typ) Total Harmonic Distortion Output Current Tolerance Output Current Ripple LF Mains Surge Capability Ambient Temperature Tcase Maximum Humidity Lifetime Control Mode Standby Power Dimming range Isolation controls input to output Open load protection Short circuit protection Over power protection Hot wiring Certificate RF Data Work mode Work frequency Modulation mode RF output power Rx sensitivity Vesta-W4 LED Driver BXDR-PS-20BS-U405W-01-A 20W 4CH (RGBW) 500/400/300/250mA 18...40Vdc 120...277VAC 0.09-0.20A 0.25A 50...60Hz 0.9 @ rated output power 84%@rated output power 15% @ rated output power ±5% 5% L-N 1kV; -20...+50°C 80°C 10~90% 50,000 hrs Wireless protocol = Wi-Fi 0.5W 10...100% Dimming Via WiZ App SELV (acc. IEC61347-1) YES YES YES YES CE-RED ENEC UKCA UL FCC . Wi-Fi: 802.11b/g Wi-Fi: 2.4...2.4835 GHz Wi-Fi: CCK/DSSS/OFDM Wi-Fi: 20 dBm Wi-Fi: -98 Wi-Fi: -74 2 /3 www.bersn.com Jan 2024 Wiring and Connections Input wire cross-section Input wire strip length Output wire cross-section Output wire strip length Maximum cable length 0.75...1.5 mm2 / AWG 18...16 8.5...9.5 mm 0.5...1.5 mm2 / AWG 20...16 8.5...9.5 mm 0.3 m Input 120277VAC Dip-switch Operation Instructions 2 Dip-switch (4 steps) Output LED/ 4CH Dimensions (mm) 3 /3 www.bersn.com Jan 2024 FCC statement This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) This device may not cause interference. 2) This device must accept any interference, including interference that may cause undesired operation of the device. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: --Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC Radiation Exposure Statement This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device must operate with a minimum distance of 20 cm between the radiator and user body.