FSP Protek Power PM101 Series 80-100W Medical & ITE AC-DC Power Supplies

Description

The PM101 series comprises AC-DC switching power supplies designed in a compact 2 x 4 x 1.29 inch package. These units can deliver 100 watts of continuous power with 7.5 CFM forced air cooling or 80 watts with convection cooling. Constructed on a printed circuit board, they are suitable for medical applications, information technology, and industrial applications. Approvals to IEC60601-1 and IEC62368-1 safety standards streamline design-in processes and reduce end-equipment compliance costs.

Certifications: [CE Mark] [RoHS Compliant]

Features

BF class insulation
Operation altitude up to 5000 meters
2 x 4 inch footprint with 1.29 inch low profile
Less than 175 μA leakage current
Wide input range: 80-264 VAC
Meets EN55011 / EN55032 and FCC Class B standards
Short-circuit protection
Compliant with RoHS requirements
No load power consumption less than 0.15W

Safety Standard Approvals

[UL Certified] UL ES 60601-1, CSA C22.2 No. 60601-1 (File No. E178020)

[TÜV Certified] TÜV EN 60601-1

[UL Certified] UL 62368-1, CSA C22.2 No. 62368-1

[TÜV Certified] TÜV EN 62368-1

Input Specifications

Input voltage: 80-264 VAC
Power derating: Derates linearly from 100% at 90VAC to 90% at 85VAC and 80% at 80VAC.
Input frequency: 47-63 Hz
Input current: 2.0 A (rms) for 115 VAC, 1.2 A (rms) for 230 VAC
Earth leakage current: 175 μA max. @ 264 VAC, 63 Hz
Touch current: 100 μA max. @ 264 VAC, 63 Hz

Output Specifications

Output voltage/current: See rating chart.
Maximum output power: See rating chart.
Ripple and noise: 1% peak to peak maximum.
Over voltage protection: Set at 112-140% of its nominal output voltage; latches by recycle input to reset.
Short circuit protection: Automatic recovery.
Over temperature protection: Latching by recycle input to reset.
Temperature coefficient: All outputs ±0.04% /°C maximum.
Transient response: Maximum excursion of 4% or better on all models, recovering to 1% of final value within 500 μs after a 25% step load change.

Environmental Specifications

Operating temperature: -20°C to +70°C
Storage temperature: -40°C to +85°C
Relative humidity: 5% to 95% non-condensing
Temperature derating: Derates from 100% at +50°C linearly to 50% at +70°C, applicable to convection and forced-air cooling conditions.

General Specifications

Switching frequency: 65 KHz (typical)
Efficiency: See rating chart.
Hold-up time: 10 ms minimum at 100 W load and 115 VAC; 10 ms minimum at 80 W load and 100 VAC.
Line regulation: ±0.5% maximum at full load.
Inrush current: 80 A @ 115 VAC or 160 A @ 230 VAC, at 25°C cold start.
Withstand voltage: 4000 VAC from input to output, 1500 VAC from input to ground, 1500 VAC from output to ground.
MTBF: 150,000 hours at full load at 25°C ambient, calculated per MIL-HDBK-217F.
EMC Performance:
- EN55011/ EN55032: Class B conducted, class B radiated
- EN61000-3-2: Harmonic distortion, class A
- EN61000-3-3: Line flicker
- EN60601-1-2, EN55024:
- EN61000-4-2: ESD, ±15 KV air and ±8 KV contact
- EN61000-4-3: Radiated immunity, 9-28 V/m
- EN61000-4-4: Fast transient/burst, ±2 KV
- EN61000-4-5: Surge, ±1 KV diff., ±2 KV com
- EN61000-4-6: Conducted immunity, 10 Vrms
- EN61000-4-8: Magnetic field immunity, 30 A/m
- EN61000-4-11: Voltage dip immunity, 30% reduction for 500 ms, 100% reduction for 10 ms

Output Voltage/Current Rating Chart

Model	V1	Max. Current at convection	Max. Current at 7.5 CFM	Tol.	Ripple & Noise⁽²⁾	Max. Power⁽¹⁾	Efficiency (typical) 115/230 Vac
PM101-12A	12 V	6.67 A	8.34 A	±2%	120 mV	80 W / 100 W	87/90%
PM101-13A	15 V	5.34 A	6.67 A	±2%	150 mV	80 W / 100 W	87/90%
PM101-13-1A	18 V	4.45 A	5.56 A	±2%	180 mV	80 W / 100 W	87/90%
PM101-14A	24 V	3.34 A	4.17 A	±2%	240 mV	80 W / 100 W	88/90%
PM101-15A	28 V	2.86 A	3.58 A	±2%	280 mV	80 W / 100 W	88/90%
PM101-16-1A	32 V	2.50 A	3.13 A	±2%	320 mV	80 W / 100 W	88/90%
PM101-17A	36 V	2.23A	2.78 A	±2%	360 mV	80 W / 100 W	88/90%
PM101-18A	48 V	1.67A	2.09A	±2%	480 mV	80 W / 100 W	88/90%

Notes:

The first value of max. power is at convection cooling. The second value is with 7.5 CFM forced air provided by user.
Ripple and noise is maximum peak to peak voltage value measured at output within 20 MHz bandwidth, at rated line voltage and output load ranges, and with a 10 μF tantalum (or electrolytic) capacitor in parallel with a 0.1 μF ceramic capacitor across the output, except model PM101-12A which uses a 22 μF tantalum (or electrolytic) capacitor in parallel with a 0.1 μF ceramic capacitor across the output.

Mechanical Specifications

Dimensions: 2 x 4 x 1.29 inches [50.8 x 101.60 x 32.8 mm]. Tolerance: 0.02 [0.5] maximum.

Input Connector (CN1): Molex header 09-65-2038, mating with Molex housing 09-50-1031 or equivalent.

Output Connector (CN2): Molex header 09-65-2048, mating with Molex housing 09-50-1041 or equivalent.

Ground Tab: 0.25 [6.35] x 0.032 [0.8] fast-on connector.

Mounting: Four mounting holes, 0.157 [4.00] diameter.

Emissions Compliance: To ensure compliance with Level B emissions, connect the three "*" marked mounting holes with metallic standoffs to the chassis.

Weight: 155 grams (0.34 lbs.) approx.

Diagram Description: The diagram shows a rectangular power supply unit with connectors labeled CN1 and CN2. CN1 is a 3-pin connector on one side, and CN2 is a 4-pin connector on the opposite side. A ground tab is indicated. Mounting holes are shown around the perimeter. Dimensions are provided in inches and millimeters.

Output Power Derating Curves

Curve 1: Output Power vs. Input Voltage

This graph shows how output power is derated based on input voltage. The Y-axis represents Output Power (%) from 80% to 100%. The X-axis represents Input Voltage (V) from 80 to 264. The curve indicates full power (100%) is available from approximately 90V to 264V, with derating occurring below 90V, reaching 80% at 80V.

Curve 2: Output Power vs. Ambient Temperature

This graph illustrates output power derating based on ambient temperature. The Y-axis represents Output Power (%) from 50% to 100%. The X-axis represents Ambient Temperature (°C) from -20 to 70. The curve shows full power (100%) is available up to 50°C, and derates linearly to 50% power at 70°C.

Pin Chart

CN1			CN2
PIN NO.	1	2	3	1	2	3	4
Polarity	Live	Void	Neutral	V1	V1	Common Return	Common Return

	FSP PM101 Series Switching Power Supply CB Test Certificate \| IEC 60601-1 Compliance CB Test Certificate for FSP PM101 series switching power supplies, detailing product specifications, safety compliance with IEC 60601-1, manufacturer information, and certification by TÜV Rheinland.
	FSP PM101 and FSP100M-K24 Series Switching Power Supply Verification of Compliance Official verification of compliance for FSP Group's PM101 and FSP100M-K24 series switching power supplies, confirming adherence to key EMC and medical electrical equipment standards as certified by SGS and Compliance Certification Services Inc.
	FSP Protek Switching Power Supply CB Test Certificate - Models PM101, PU101 Series Official CB Test Certificate issued by TÜV Rheinland for FSP Group Inc. (Protek trademark) Switching Power Supplies, models PM101 and PU101 series, compliant with IEC 62368-1:2014.
	FSP PM101 and FSP100M-K24 Series Switching Power Supply UL Compliance Certificate Official UL compliance certificate for FSP PM101 and FSP100M-K24 series switching power supplies, detailing safety standards and product models. Includes information on UL/cUL medical category compliance.
	FSP Group Inc. Power Supply Safety Certifications and Model Information This document compiles safety certification details for FSP Group Inc. power supplies, including model numbers, manufacturing plants, and compliance standards tested by TÜV Rheinland. Covers various PM101, PU101, and FSP100-K24 series power supplies.
	FSP Switching Power Supply Safety Certifications - IEC 60601 Compliant This document contains safety certifications for FSP Group Inc.'s switching power supplies, including the PM101 and FSP100M-K24 series, tested to IEC 60601 standards by TÜV Rheinland. It details product designations, voltage, current, and manufacturing locations.
	FSP Switching Power Supply CB Test Certificate for IEC 62368-1 Compliance Official CB Test Certificate issued by TÜV Rheinland for FSP Group Inc. Switching Power Supplies, models PM101 and PU101 series, demonstrating compliance with IEC 62368-1:2014 safety standards.
	FSP Switching Power Supply Safety Certificates - TÜV Certified Models Official TÜV Rheinland safety certificates for FSP Group Inc. switching power supplies, including models from the PM101, PU101, and FSP100-K24 series, certified to EN 62368-1.

FSP Protek Power 80-100 Watt Medical & ITE Power Supplies