Sunrise Alarm Clock with Himalayan Salt Lamp & Wireless Charger

Model: EAC-SU21

Introduction

This manual provides instructions for operating your EAC-SU21 Sunrise Alarm Clock with Himalayan Salt Lamp and Wireless Charger. Please read all instructions carefully before use and keep this manual for future reference.

In the Box

EAC-SU21 Sunrise Alarm Clock with Wireless Charger (x1)
Charging Cable (x1)
Instruction Manual (x1)

Safety Precautions

This product is not a toy; keep away from children and pets.
Use the device only as instructed in this manual.
This device is not a substitute for professional medical equipment or attention.
Only use the supplied charging cable.
Do not open or attempt to repair the unit yourself to avoid risks of fire, shock, or injury.
Store the device in a dry, cool location away from water or heat sources when not in use.
Do not expose the device or charging cable to extreme temperatures, open flames, or wet conditions.
Do not submerge in water or use where it could fall into liquid.
Unplug the charging cable when not in use. Do not pull the cable to disconnect or use it as a handle.
Do not use if the device or charging cable is damaged. Contact the manufacturer or service agent for repair or replacement.
Attachments on the back of your device can interfere with wireless charging and cause overheating. Remove attachments before charging.

Product Overview

The clock features several buttons and ports:

[SNOOZE/LIGHT] Button: Located on the top, used for snooze and light control.
Clock Display: Shows time, alarm, date, and temperature.
[SET] Button: Used for setting time, alarm, date, and saving settings.
[UP] Button: Used for adjusting settings and changing display modes.
[DOWN] Button: Used for adjusting settings, toggling 12/24 hour format, and switching temperature units.
Wireless Charging Surface: Located on the top, for charging compatible devices.
Power Input Port: USB-C port for connecting the charging cable.
USB Power Output Port: For charging other USB devices.

Diagram Description: A diagram shows the front of the clock with the display and SNOOZE/LIGHT button. The back of the clock shows the SET, UP, and DOWN buttons, the USB-C power input port, and a USB power output port. The display shows "88:88". The power input is labeled "INPUT 9V/3A" and the output is labeled "OUTPUT 5V/1A".

Connecting to Power

1. Plug the small connector of the included charging cable into the USB-C charging port on the clock.

2. Plug the large connector into a USB power source, such as a compatible 5V USB power adapter (not included), and plug into a wall outlet.

The clock display will turn on. If disconnected from power, time and settings are saved for 60 seconds.

Display Modes

Press the [UP] button to switch between display modes. Press [SET] to save the current mode as default.

Mode 1: Shows time for 10 seconds, then date and temperature for 2 seconds.
Mode 2: Shows time, alarm, date, and temperature continuously.

Setting the Time

Press [SET] until time is displayed.
Press [DOWN] to toggle between 12-hour and 24-hour clock format.
Press and hold [SET] to set the hour. The hour digits will flash. Use [UP] and [DOWN] to adjust. A dot appears in the upper left for PM. Press [SET] to save the hour.
The minute digits will flash. Use [UP] and [DOWN] to adjust. Press [SET] to save. The clock returns to default display.

Display example: "00:00 00:00" showing AM/PM indicator.

Setting the Alarm

Press [SET] until the alarm time is displayed.
Press [DOWN] to turn the alarm ON or OFF. A dot in the lower left corner indicates the alarm is ON.
When the alarm is ON, press and hold [SET] to set the alarm time. The hour digits will flash. Use [UP] and [DOWN] to adjust. Press [SET] to save the hour.
The minute digits will flash. Use [UP] and [DOWN] to adjust. Press [SET] to save. The clock returns to default display.

Display example: "00:00 00:00" showing Alarm OFF / Alarm ON status.

Setting the Date

Press [SET] until the date is displayed.
Press and hold [SET] to set the date. The year will flash. Use [UP] and [DOWN] to adjust. Press [SET] to save the year.
The month will flash. Use [UP] and [DOWN] to adjust. Press [SET] to save the month.
The day will flash. Use [UP] and [DOWN] to adjust. Press [SET] to save the day. The clock returns to default display.

Changing Temperature Units

Press [SET] until the temperature is displayed.
Press [DOWN] to switch between degrees Fahrenheit (°F) and Celsius (°C).
Press [SET] to save. The clock returns to default display.

Using the Bedside Light

Press the [SNOOZE/LIGHT] button to turn the bedside light ON (white light mode).
Press [SNOOZE/LIGHT] again to adjust brightness (low, medium, high).
Press and hold [SNOOZE/LIGHT] to switch to color-changing light mode.
In color mode, press [SNOOZE/LIGHT] to select a color.
Press and hold [SNOOZE/LIGHT] again to switch back to white light mode.

Note: The bedside light can only be turned OFF from white light mode. It cannot be used during sunrise mode or snooze mode.

Using the Sunrise Light

The sunrise light function activates 20 minutes before your set alarm time, gradually increasing brightness until the alarm sounds.

To use: Set the alarm before going to sleep.

Snooze Function

When the alarm sounds, press the [SNOOZE/LIGHT] button to activate Snooze. The alarm will repeat in 5 minutes, and the sunrise light will remain at full brightness.

To turn the alarm and sunrise light off completely for the day, press and hold the [SNOOZE/LIGHT] button when the alarm sounds. They will reactivate the next day.

Wireless Charging & USB Output

Wireless Charging:

When connected to power, the LED indicator flashes RED and BLUE alternately, then turns RED, indicating standby.
Place a wireless charging-enabled device on the charging pad. Charging begins automatically. The LED indicator turns BLUE while charging.
If charging doesn't start, reposition the device or remove its case, as attachments can interfere.
When fully charged, the LED indicator turns RED. Remove the device.

LED Indicator Status:

Flashing RED/BLUE: Not wireless charging enabled device or interference.
Solid BLUE: Device is charging.
Solid RED: Charging complete.

Note: For optimal wireless charging, use a 20W or higher power adapter (not included).

USB Output:

To power or charge a USB device, plug its USB connector into the USB output port on the back of the clock.

Technical Specifications

Input: DC 5V/3A, 9V/2A
Wireless Charging Output: 5W/7.5W/10W/15W
Wireless Charging Range: 6mm
USB Output: DC 5V/1A
Working Temperature: 32°F ~ 122°F (0°C ~ 50°C)

FCC Information

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

FCC ID: 2ALCFXO-9917

Made in China