User Manual for CVTE models including: SKOW603501, 2AR82-SKOW603501, 2AR82SKOW603501, SKO.W603.5, 2T2R USB Wi-Fi Module, SKO.W603.5 2T2R USB Wi-Fi Module
Guangzhou Shikun Electronics Co., Ltd SKOW603501 IEEE 802.11b/g/n 2T2R USB Wi-Fi Module 2AR82-SKOW603501 2AR82SKOW603501 skow603501
File Info : application/pdf, 16 Pages, 990.63KB
DocumentDocumentGuangzhou Shikun Electronic Technology Company Limited SPECIFICATION SKO.W603.5<002.029.0000260> IEEE 802.11b/g/n 2T2R USB Wi-Fi Module CVTE SKO.W603.5 TCL CVTE SKO.W603.5 Checked by Approved by Shikun Rechecked by Approved by Please send the original back to us after you have approved and signed. Comments Approved by customer Approved by Company's seal Customer's Name: QR-ZZPJ-017 CVTE REVISION HISTORY VERSION DATE V0 2020.08.14 BOARD ID SKO.W603.5 B20161 PAGE All DESCRIPTION First Issued. AUTHOR CVTE Content 1. Introduction...................................................... 1 2. FEATURES ....................................................... 1 3. Block Diagram ............................................... 1 4. Package Outline and Mounting ......................... 2 5. Pin Definition................................................. 2 6. Product Pictures .............................................. 3 7. Materials BOM BOM .............................................. 4 8. General Requirements........................................ 4 9. Electrical Characteristics ..................................... 4 9.1 IEEE 802.11b Section ................................................................ 5 9.2 IEEE 802.11g Section ................................................................ 5 9.3 IEEE 802.11n HT20 Section ........................................................ 6 9.4 IEEE 802.11n HT40 Section ........................................................ 7 10. Software Requirements ..................................... 8 CVTE SKO.W603.5 1. Introduction SKO.W603.5 module is based on MEDIATEK MT7603U solution. The MT7603U is a highly integrated Wi-Fi single chip which supports 300 Mbps PHY rate. It fully complies with IEEE 802.11n and IEEE 802.11 b/g standards, offering feature-rich wireless connectivity at high standards, and delivering reliable, cost-effective throughput from an extended distance. This documentation describes the engineering requirements specification. SKO.W603.5 MEDIATEK MT7603U MT7603U Wi-Fi 300 Mbps IEEE 802.11n IEEE 802.11 b/g 2. FEATURES Reserving System Chip Solution Band Dimensions IEEE Std. 802.11b IEEE Std. 802.11g IEEE Std. 802.11n MT7603U 2.4GHz 45.0mm*30.0mm*3.4mm Model SKO.W603.5 Installation Mode Ext-WIFI Radio Technology IEEE 802.11b/g/n Operation Frequency 2.4GHz Antenna Port PCB On-board PCB Antenna Remark 45.0mm*30.0m m*3.4mm 3. Block Diagram QR-ZZPJ-017A 1 CVTE SKO.W603.5 4. Package Outline and Mounting 5. Pin Definition PIN 1 2 3 4/5/6 7 SYMBOL GND USB_DP USB_DM 3.3V WoWWLAN 8 RESET 9 GND DESCRIPTION Connected to Ground\ USB2.0 DP Signal\USB2.0 USB2.0 DM Signal\USB2.0 VDD 3.3V\+3.3V Wake on Wireless LAN 10K 3.3V RESET\ 10K 3.3V Connected to Ground\ QR-ZZPJ-017A 2 CVTE 6. Product Pictures SKO.W603.5 top view bottom view Nameplate content QR-ZZPJ-017A 3 CVTE SKO.W603.5 7. Materials BOM BOM Número 1 2 3 Componentes clave Circuito integrado PCB Oscilador de cristal Modelo MT7603U SKO.W603.5 2.3.3.400001208 Especificaciones 48-QFN FR-4,2LAY 40MHz Observación ---- 8. General Requirements No. Feature Description 8-1 Operation Voltage 8-2 Current Consumption 8-3 Ripple 8-4 Operation Temperature 8-5 Antenna Type 8-6 USB 8-7 Storage Temperature 3.3V±0.3V 430mA 100mV 0°C to +40°C Internal antenna High Speed USB 2.0 Interface -40°C to +85°C 9. Electrical Characteristics The Test for electrical specification was performed under the following condition unless otherwise specified. Ambient condition Temperature :25 ± 5; Power supply voltages3.3V (±0.3V) input power at the Module. QR-ZZPJ-017A 4 CVTE SKO.W603.5 25±5 3.3V±0.3V 9.1 IEEE 802.11b Section Items Specification Mode Channel Data rate TX Characteristics 1. Power Levels(Calibrated) 1) For Each antenna port 2. Spectrum Mask @ target power 1) fc +/-11MHz to +/-22MHz 2) fc > +/-22MHz 3 Constellation Error(EVM)@ target power 1) 1Mbps 2) 2Mbps 3) 5.5Mbps 4) 11Mbps 4. Frequency Error RX Characteristics 5 Minimum Input Level Sensitivity (each chain) 1) 1Mbps (FER 8%) 2) 2Mbps (FER 8%) 3) 5.5Mbps (FER 8%) 4) 11Mbps (FER 8%) 6 Maximum Input Level (FER 8%) Min. 14 - -20 Min. -10 9.2 IEEE 802.11g Section Contents IEEE802.11b CCK CH1 to CH13 1, 2, 5.5, 11Mbps Typ. Max. Unit Remark 16 18 dBm - -30 dBr - -50 dBr Typ. -10 -10 -10 -10 20 Max. dB dB dB dB ppm Unit - -83 dBm - -80 dBm - -79 dBm - -76 dBm - - dBm Items Specification Mode Channel Data rate TX Characteristics 1. Power Levels 1) For Each antenna port 2. Spectrum Mask @ target power 1) at fc +/-11MHz Min. 12 - Contents IEEE802.11g OFDM CH1 to CH13 6, 9, 12, 18, 24, 36, 48, 54Mbps Typ. Max. Unit Remark 14 16 dBm - -20 dBr QR-ZZPJ-017A 5 CVTE SKO.W603.5 2) at fc +/-20MHz 3) at fc > +/-30MHz 3 Constellation Error(EVM)@ target power 1) 6Mbps 2) 9Mbps 3) 12Mbps 4) 18Mbps 5) 24Mbps 6) 36Mbps 7) 48Mbps 8) 54Mbps 4 Frequency Error RX Characteristics 5 Minimum Input Level Sensitivity (each chain) 1) 6Mbps (PER 10%) 2) 9Mbps (PER 10%) 3) 12Mbps (PER 10%) 4) 18Mbps (PER 10%) 5) 24Mbps (PER 10%) 6) 36Mbps (PER 10%) 7) 48Mbps (PER 10%) 8) 54Mbps (PER 10%) 6 Maximum Input Level (PER 10%) - -20 Min. -20 - Typ. - -28 -40 -5 -8 -10 -13 -16 -19 -22 -25 20 Max. dBr dBr dB dB dB dB dB dB dB dB ppm Unit -85 dBm -84 dBm -82 dBm -80 dBm -77 dBm -73 dBm -69 dBm -65 dBm - dBm 9.3 IEEE 802.11n HT20 Section Items Specification Mode Channel Data rate (MCS index) TX Characteristics 2. Power Levels 1) For Each antenna port 3. Spectrum Mask @ target power 1) at fc +/-11MHz 2) at fc +/-20MHz 3) at fc > +/-30MHz 4. Constellation Error(EVM)@ target power 1) MCS0 2) MCS1 3) MCS2 Min. 11 - - Contents IEEE802.11n HT20 @ 2.4GHz OFDM CH1 to CH13 MCS0/1/2/3/4/5/6/7 Typ. Max. Unit 13 15 dBm - -20 dBr - -28 dBr - -45 dBr - -5 dB - -10 dB - -13 dB QR-ZZPJ-017A 6 CVTE SKO.W603.5 4) MCS3 5) MCS4 6) MCS5 7) MCS6 8) MCS7 5. Frequency Error RX Characteristics 6. Minimum Input Level Sensitivity (each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 7. Maximum Input Level (PER 10%) -20 Min. Typ. - - - - - - - - - - - - - - - - -20 - 9.4 IEEE 802.11n HT40 Section -16 -19 -22 -25 -28 20 Max. -82 -79 -77 -74 -70 -66 -65 -64 - dB dB dB dB dB ppm Unit dBm dBm dBm dBm dBm dBm dBm dBm dBm Items Contents Specification IEEE802.11n HT40 @ 2.4GHz Mode OFDM Channel CH3 to CH11 Data rate (MCS index) TX Characteristics Min. Min. MCS0/1/2/3/4/5/6/7 Typ. Max. Unit Typ. Max. Unit Remark 1. Power Levels (Calibrated) 1) For Each antenna port 11 13 15 dBm 2. Spectrum Mask @target power 1) at fc +/-22MHz - - -20 dBr 2) at fc +/-40MHz - - -28 dBr 3) at fc > +/-60MHz - - -45 dBr 3. Constellation Error(EVM)@ target power 1) MCS0 - - -5 dB 2) MCS1 - - -10 dB 3) MCS2 - - -13 dB 4) MCS3 - - -16 dB 5) MCS4 - - -19 dB 6) MCS5 - - -22 dB 7) MCS6 - - -25 dB 8) MCS7 - - -28 dB QR-ZZPJ-017A 7 CVTE SKO.W603.5 4. Frequency Error RX Characteristics 5. Minimum Input Level Sensitivity (each chain) 1) MCS0 (PER 10%) 2) MCS1 (PER 10%) 3) MCS2 (PER 10%) 4) MCS3 (PER 10%) 5) MCS4 (PER 10%) 6) MCS5 (PER 10%) 7) MCS6 (PER 10%) 8) MCS7 (PER 10%) 6. Maximum Input Level (PER 10%) -20 Min. Typ. 20 Max. ppm Unit - - -79 dBm - - -76 dBm - - -74 dBm - - -71 dBm - - -67 dBm - - -63 dBm - - -62 dBm - - -61 dBm -20 - - dBm 10. Software Requirements The driver supports the following operating systems: Microsoft Windows XP, Vista and Win7. Window QR-ZZPJ-017A 8 CVTE FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. The device must be professionally installed The intended use is generally not for the general public. It is generally for industry/commercial use. The connector is within the transmitter enclosure and can only be accessed by disassembly of the transmitter that is not normally required. the user has no access to the connector. Installation must be controlled. Installation requires special training CFR 47 FCC Part 15 Subpart C (15.247, DTS ) has been investigated. It is applicable to the modular transmitter This radio transmitter 2AR82-SKOW603501 has been approved by Federal Communications Commission to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. Antenna 1 2 Frequency (MHz) 2412-2462 2412-2462 Antenna Type PCBA Antenna PCBA Antenna MAX Antenna Gain (dBi) 1.38 1.43 QR-ZZPJ-017A 9 CVTE Canada Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d'Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1)L'appareil ne doit pas produire de brouillage; 2)L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Please notice that if the ISED certification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains IC: 24728-SKOW603501" any similar wording that expresses the same meaning may be used. l'appareil hôte doit porter une étiquette donnant le numéro de certification du module d'Industrie Canada, précédé des mots « Contient un module d'émission », du mot « IC: 24728-SKOW603501» ou d'une formulation similaire exprimant le même sens, comme suit The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 etla conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne surl'exposition et la conformité de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimè tres entre le radiateur et votre corps. the required impedance for each antenna type : 50 ohm l'impédance requise pour chaque type d'antenne : 50ohm QR-ZZPJ-017A 10 CVTE Antenna 1 2 Frequency (MHz) 2412-2462 2412-2462 Antenna Type PCBA Antenna PCBA Antenna MAX Antenna Gain (dBi) 1.38 1.43 Notice to OEM integrator Must use the device only in host devices that meet the FCC/ISED RF exposure category of mobile, which means the device is installed and used at distances of at least 20cm from persons. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The end user manual shall include FCC Part 15/ISED RSS GEN compliance statements related to the transmitter as show in this manual. (FCC/ Canada Statement). Host manufacturer is responsible for compliance of the host system with module installed with all other applicable requirements for the system such as Part 15 B, ICES 003. The devices must be installed and used in strict accordance with the manufacturer's instruction as described in the user documentation that comes with the product. Any company of the host device which install this modular should perform the test of radiated & condicted emission and spurious emission etc. according to FCC Part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement, only if the test result comply with FCC part 15C: 15.247 and 15.209 & 15.207, 15B class B requirement. Then the host can be sold legally. This modular transmitter is only FCC authorized for the specific rule parts ( 47CFR Part 15.247) listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. Host manufacturer is strongly recommended to confirm compliance with FCC/ISED requirements for the transmitter when the module is installed in the host. Must have on the host device a label showing Contains FCC ID: 2AR82-SKOW603501 and Contains IC: 24728-SKOW603501 The use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturer's instruction manual. This module is stand-alone modular. If the end product will involve the Multiple simultaneously transmitting condition or different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with module manufacturer for the installation method in end system. l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc / (catégorie d'exposition rf mobile, ce qui signifie le dispositif est installé et utilisé à une distance d'au moins 20 cm de personnes. QR-ZZPJ-017A 11 CVTE le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de conformité relatives à l'émetteur que de montrer dans ce manuel. le fabricant est responsable de la conformité de l'hôte, le système d'accueil avec le module installé avec toutes les autres exigences applicables du système comme la partie 15 b, ices - 003. accueillir le fabricant est fortement recommandé de confirmer la conformité avec les exigences de la fcc / (émetteur lorsque le module est installé dans l'hôte. le dispositif d'accueil doivent avoir une étiquette indiquant contient FCC ID: 2AR82SKOW603501, d'émission IC: 24728-SKOW603501 QR-ZZPJ-017A 12 CVTEAcrobat Distiller 20.0 (Windows)