AFX LIGHT SPOT100-LED User Manual

Unpacking Instructions

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present and have been received in good condition. Notify the freight company immediately and retain packing material for inspection if any parts appear to be damaged from shipping or the carton itself shows signs of mishandling. Keep the carton and all packing materials. In the event that a fixture must be returned to the factory, it is important that the fixture be returned in the original factory box and packing.

Contents of the Carton

• 1 pc. SPOT100-LED
• 1 pc. user manual
• 1 pc. powercon mains lead
• 1 pc. omega bracket

Explanation of Symbols

• ⚡ The triangle containing a lightning symbol indicates risk to health (e.g., electric shock).
• ⚠️ An exclamation mark in a triangle indicates particular risks in handling or operating the appliance.
• CE The unit complies with CE standards.
• UK The unit complies with UK standards.
• ? For indoor use only.
• 0.5m Minimum distance between the appliance and other objects.

Safety Recommendations

• Read these instructions carefully; they include important information about the installation, usage, and maintenance of this product.
• Keep this User Guide for future reference. If you sell the unit to another user, ensure they also receive this instruction booklet.
• Always ensure you are connecting to the proper voltage, and that the line voltage is not higher than that stated on the fixture.
• The appliance is Class I and must be connected exclusively to an earthed mains outlet.
• This product is intended for indoor use only!
• To prevent fire or shock, do not expose the fixture to rain or moisture. Ensure no flammable materials are close to the unit during operation.
• Install the unit in a location with adequate ventilation, at least 50cm (20in) from adjacent surfaces. Ensure ventilation slots are not blocked.
• The minimum distance from the luminaire to the lighted object is 0.5m.
• The maximum ambient temperature (Ta) is 40°C. Do not operate the fixture at higher temperatures.
• DO NOT TOUCH the housing barehanded during operation. Turn off the power and allow about 15 minutes for the unit to cool down before servicing.
• DO NOT OPEN the unit within 5 minutes after switching off.
• In case of a serious operating problem, stop using the unit immediately. Never attempt to repair the unit yourself. Repairs by unskilled people can lead to damage or malfunction.
• Make sure the power cord is never crimped or damaged.
• Never disconnect the power cord by pulling or tugging on the cord.
• Avoid direct eye exposure to the light source, as it may cause epileptic shock in sensitive individuals.
• The product is for decorative purposes only and not suitable as household illumination.
• If the external flexible cable or cord is damaged, it must be replaced by the manufacturer, service agent, or a similarly qualified person to avoid hazards.
• The appliance must be replaced if it is damaged or thermally deformed.
• The LED protection screen must be replaced if visibly damaged to the point of impairing its effectiveness (e.g., due to cracks or deep scratches).
• The light source is not replaceable; when it reaches the end of its life, the entire luminaire must be replaced.

Disconnect Device

Where the MAINS plug or an appliance coupler is used as the disconnect device, it shall remain readily operable.

Installation

This fixture may be mounted vertically on a ceiling or truss, or placed on a level surface, provided there is adequate room for ventilation.

Rigging

The LED moving head provides a unique mounting bracket assembly that integrates the base, the included 'omega bracket', and the safety cable rigging point. When mounting on a truss, use an appropriate clamp with the omega bracket and an M10 screw through the center hole. As an added safety measure, attach at least one properly rated safety cable to the fixture using the integrated rigging points.

Fuse Replacement

• Disconnect the power cord before replacing a fuse and always replace with the same type fuse.
• Turn the fuse knob to access the fuse.
• Remove the damaged fuse and replace with the same type.
• Close the fuse compartment and reconnect power.

DMX Connection

Connect an XLR cable from your controller's 3-pin XLR output to the fixture's 3-pin XLR input. A serial data link is needed for light shows with one or more fixtures using a DMX-512 controller, or for synchronized shows in master/slave mode. The total number of channels required by all fixtures on a link determines the link's capacity.

Important: Fixtures must be daisy-chained in a single line. Maximum recommended serial data link distance: 100 meters (328ft). Maximum recommended number of fixtures: 11.

The cable should be two-core, screened cable with XLR input and output connectors.

Data Cabling

To link fixtures, use data cables. For custom cables, use data-grade cables for high-quality signals, less prone to electromagnetic interference.

Cable Connectors

Cabling requires a male XLR connector on one end and a female XLR connector on the other. Termination reduces signal errors. Connecting a DMX signal terminator is advisable to avoid transmission problems and interference.

Caution

Do not allow contact between the common and the fixture's chassis ground. Grounding the common can cause a ground loop and erratic performance. Test cables with an ohm meter to check polarity and ensure pins are not grounded or shorted to the shield.

Rear Panel Description

1. DMX IN: Connect a DMX cable from a DMX controller's output.
2. DMX OUT: Connect this output to a slave unit's DMX input.
3. POWER IN: Connect the supplied mains lead to this connector and a wall outlet.
4. POWER OUT: Connect this output to a slave unit's POWER IN connector.
5. ON/OFF switch.
6. 3A fuse.

Control Panel

The control panel configures settings via an LCD screen and buttons:

• 1. DMX: Lights up when the unit is in DMX mode and receives a DMX signal.
• 2. ERR: Lights up when a fault is detected.
• 3. LCD Screen: Shows current settings.
• 4. <←>: Scrolls through first-level options or exits menu/function.
• <↑>: Navigates up or increases numeric value.
• <↓>: Navigates down or decreases numeric value.
• : Enables menu or confirms selected value.

Interface Description (Subinterface Settings)

Manual Control

This interface controls the fixture in Master mode (does not receive DMX, sends DMX to slave).

The orange arrow indicates the selected menu item. Press OK to enter edit mode. The item turns red. Use UP/DOWN to select value, then OK to save and exit.

System

Lamp Temp

Access sub-menu to view channel values.

DMX Monitor

Displays channel values for viewing.

System Errors

The red ERR indicator flashes for error messages. Navigate to "System Information" -> "System Error" to view the message. After addressing the error, you can clear the error record by selecting "Clear Error" -> OK.

Error List:

• MT board connection failed
• Pan Reset failed
• Tilt Reset failed
• Pan Hall failed
• Tilt Hall failed
• Color Wheel Reset failed
• Gobo Wheel Reset failed
• Focus Reset failed

Advanced Settings

Password: "▲▲▲▼▼▼" (three up, three down). Press OK to enter the Advanced menu.

DMX Channel Table (14 Channel Mode)

Fixture Cleaning

Clean internal and external optical lenses and mirrors periodically due to fog residue, smoke, and dust to optimize light output. Cleaning frequency depends on the environment. For heavy club use, clean monthly. Periodic cleaning ensures longevity and crisp output.

1. Wipe the casing with normal glass cleaner and a soft cloth.
2. Brush the cooling vents and fan grill.
3. Clean external optics with glass cleaner and a soft cloth every 20 days.
4. Clean internal optics with glass cleaner and a soft cloth every 30-60 days.
5. Ensure all parts are completely dry before plugging the unit back in.

Specifications

• Power supply: 100-240V~ 50/60Hz
• Consumption: 150W
• Fuse: 3A
• Light source: White 100W LED
• Illumination: 3420 Lux@5m Ø124cm
• Beam angle: 15°
• Pan/tilt: 540°/270°
• Dimmer: 0-100%
• Strobe: 1-20 flashes/sec.
• Dimensions: 280 x 215 x 370mm
• Weight: 5.9kg

Product Disposal

♻️ IMPORTANT NOTE: Electric products must not be disposed of with household waste. Please bring them to a recycling center. Ask your local authorities or dealer for instructions.