User Guide for MicroTouch models including: IC-156P-AW3, All -In-One Touch Computer, IC-156P-AW3 All -In-One Touch Computer
Sep 30, 2021 — The information in this document is subject to change without notice. MICROTOUCH makes no representations or warranties with respect to the contents herein, ...
File Info : application/pdf, 29 Pages, 1.45MB
DocumentDocumentUser Guide IC-156P-AW3 Touch Computer Version 1.2 2022/02 About This Document No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior written permission of MICROTOUCH. The information in this document is subject to change without notice. MICROTOUCH makes no representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a particular purpose. MICROTOUCH reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of MICROTOUCH to notify any person of such revisions or changes. Windows is a registered trademark of Microsoft, Inc. Other brand or product names are trademarks of their respective holders. 1 Compliance Information For FCC (USA) This equipment has been tested and fund to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. There limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For IC (Canada) CAN ICES-3(A)/NMB-3(A) For CE (EU) The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive 2014/35/EU Disposal Information Waste Electrical and Electronic Equipment This symbol on the product indicates that, under the European Directive 2012/19/EU governing waste from electrical and electronic equipment, this product must not be disposed of with other municipal waste. Please dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources. For more information about recycling of this product, please contact your local city office or your municipal waste disposal service. 2 | Renseignements relatifs à la conformité Pour la FCC (États-Unis). Ce matériel a fait l'objet d'essais qui ont déterminé qu'il respectait les limites d'un appareil de classe A selon la partie 15 des règlements de la FCC. Ces limites sont établies pour assurer une protection raisonnable contre les parasites nuisant à un fonctionnement dans un environnement commercial. Ce matériel génère, utilise et peut émettre des ondes radio électriques, et lorsqu'il n'est pas installé et utilisé selon le manuel d'instructions, peut causer des parasites nuisant aux communications radio. L'utilisation de ce matériel dans une zone résidentielle est susceptible de causer des parasites auquel cas l'utilisateur est tenu de corriger le problème des parasites à ses propres frais. L'appareil respecte la partie 15 des règlements de la FCC. Le fonctionnement doit respecter les deux conditions suivantes : 1) cet appareil ne doit pas causer de parasites et (2) cet appareil doit accepter tous les parasites reçus, notamment ceux pouvant causer un fonctionnement non voulu. Pour Industrie Canada Norme canadienne NMB-3(A) Pour la CE (UE) L'appareil respecte la directive 2014/30/UE relative à la compatibilité électromagnétique et la directive 2014/35/EU sur les limites de basse tension 3 | Usage Notice ! Warning - To prevent the risk of fire or shock hazards, and do not expose the product to moisture. ! Warning - Please do not open or disassemble the product as this may cause electric shock. ! Warning - Power cord shall be connected to a socket-outlet with earth connection. ! Warning - The cable cover cannot be removed under normal use conditions. ! Warning - Stability Hazard. The touch monitor may fall, causing serious personal injury or death. To prevent injury, this touch monitor must be securely attached to the wall in accordance with the installation instructions. Precautions Please follow all warnings, precautions and maintenance as recommended in this user's manual to maximize the life of your unit. Do Turn off the product before cleaning. Use a soft cloth moistened with mild detergent to clean the product housing. Use only the qualified power adapter that comes with your device. Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time. Don't Do not use abrasive cleaners, waxes or solvents for your cleaning. Do not operate the product under the following conditions: - Extremely hot, cold or humid environment. - Areas susceptible to excessive dust and dirt. - Near any appliance generating a strong magnetic field. Caution Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. 4 | Avis d'utilisation ! Mise en garde -- Pour prévenir les risques d'incendie ou d'électrocution, ne pas exposer le produit à l'humidité. ! Mise en garde -- Prière de ne pas ouvrir ou démonter le produit, car cela pourrait entraîner l'électrocution. ! Mise en garde Le cordon d'alimentation doit être branché à une prise pourvue d'une mise à la terre. ! Mise en garde La gaine du câble ne doit pas être retirée en conditions normales d'utilisation. ! Mise en garde -- Risque de renversement. Le moniteur tactile peut se renverser et causer de graves blessures corporelles, voire la mort. Pour prévenir les blessures, ce moniteur tactile doit être solidement fixé au mur selon les instructions d'installation. Précautions Veuillez suivre toutes les mises en garde, précautions et entretiens recommandés dans ce manuel d'utilisation pour maximiser la durée de vie de votre unité. À faire : Éteindre l'appareil avant de le nettoyer. Utiliser un chiffon humidifié par une solution savonneuse pour nettoyer le boîtier du produit. Utiliser uniquement l'adaptateur d'alimentation prescrit pour votre appareil. Débrancher l'appareil lorsqu'il n'est pas utilisé pendant une période prolongée. À éviter : Ne pas utiliser de nettoyants abrasifs, de cires ou de solvants pour le nettoyage Ne jamais utiliser l'appareil dans les conditions suivantes : des conditions environnementales extrêmes (chaud, froid ou humidité) des endroits remplis de poussières et de saletés. à proximité d'appareils produisant un fort champ magnétique. Mise en garde Risque d'explosion si la batterie est remplacée par un type incorrect. Jetez les piles usagées conformément aux instructions. 5 | Table of Contents Chapter 1 ........................................................................................................................ 7 1.1 Overview .................................................................................................................... 8 1.2 Feature ....................................................................................................................... 8 1.3 Specifications ............................................................................................................. 8 1.4 Block Diagram.......................................................................................................... 10 1.5 Interface Connectors................................................................................................ 11 1.6 Package Overview ................................................................................................... 14 Chapter 2 ...................................................................................................................... 15 2.1 About VESA Mount .................................................................................................. 16 2.2 Power On / Off Switch.............................................................................................. 17 2.3 Dimension ................................................................................................................ 18 2.4 Optional Accessory Installation ................................................................................ 21 2.4.1 Install the Stand ............................................................................................... 21 2.4.2 Remove the Stand ........................................................................................... 21 2.4.3 Install the Cables.............................................................................................. 22 2.4.4 Install the Camera Module ............................................................................... 22 2.4.5 Remove the Camera ........................................................................................ 23 2.4.6 Install the MSR Module .................................................................................... 24 2.4.7 Remove the MSR Module ................................................................................ 25 Appendix ...................................................................................................................... 27 Declaration of the Presence Condition of the Restricted Substances Marking .............. 28 6 | Chapter 1 Product Introduction 7 | 1.1 Overview The IC-156P-AW3 is a thin 15.6" touch computer that offers a unique design with expandability and flexibility, making expansion and accessory installation easy. The versatility of IC-156P-AW3 is an exceptional choice for applications in all business sectors, especially in the retail market. 1.2 Feature Intel I3-7100U processor. Sleek design for a better user experience. Patented I/O design for better wiring management while implementation. 1.3 Specifications System CPU GPU DDR Storage Input Power Display Touch Audio Network Intel I3-7100U Processor, 3MB Cache, up to 2.4 GHz Intel HD Graphics 620 2 x SO-DIMM, DDR4, Support up to 32GB/64bits, 2133MT/s 1 x M.2 2280 (SATA III & NVME) DC in 24V/5A 4PIN Dual channel LVDS, resolution up to 1920x1080P60 ZCC (EETI 80W60 controller) /TPK (EETI 80H84 controller) 15.6-inch P-Cap touch sensor, supports 10 fingers touch function. 2 x speaker (2W x 2) Gigabit Ethernet (Intel i219LM) Optional m.2 2230 module: Intel AC 3168, Wi-Fi 802.11a/b/g/n/ac 1T1R, Bluetooth 4.2 (Support BLE) 8 | External IO Ports Internal IO Ports (inside plastic cover) OS version Operation temp. Storage temp. Operation humidity Storage humidity LCD Touch Panel Size Brightness (non-touch screen) Brightness (P-CAP with ZCC) Brightness (P-CAP with TPK) Number of Pixels Tilt Angle Environment Certificate Mounting Dimension (W x H x D) 1 x Power button 1 x USB Type-C (USB3CM:1x USB 3.1 gen1 with Display ALT Mode and PD2.0, support 5V@3A / 12V@2.5A output, Maximum 30W.) 1 x MiniDP (4K@60HZ) 2 x USB2.0 Type-A, 2 x USB3.0 Type-A 1 x LAN (Support 10/100/1000Mbps) 1 x DB9 (RS232, pin9 with NA/5V/12V support that select by BIOS) 1 x 24V DC In 3 x connector (5V/0.5A) Windows 10 0°C~40°C -20°C to 60°C 20~80%, Non-Condensing 10~90%, Non-Condensing 15.6" TFT LCD Typical 450 cd/m2; Min. 360 cd/m2 Typical 382 cd/m2; Min. 306 cd/m2 Typical 387 cd/m2; Min. 313 cd/m2 1920 (H) × 1080 (V)/ 60Hz 8°~68° CEFCCLVDUKCA VESA 100 mm x 100 mm System Only369.1 mm x 223.7 mm x 35.2 mm System with Stand Module369.1 mm x 291.6 mm x 169.4 mm 9 | Net Weight Gross Weight System Only2.01 Kg System with Stand Module4.01 Kg System Only3.01 Kg System with Stand Module6.01 Kg 1.4 Block Diagram 10 | 1.5 Interface Connectors 24V DC In Pin # 1 3 Signal Name GND 24V Pin # 2 4 Signal Name GND 24V RJ45 for LAN Pin # 1 3 5 7 LED LED1 LED2 Signal Name TP1+ TP2+ TP3+ TP4+ Function 1000 Speed 100 10 Active Pin # Signal Name 2 TP1- 4 TP3- 6 TP2- 8 TP4- Color Orange Green Non Yellow USB-C 11 | Pin # A1 A2 A3 A4 A5 Signal Name GND SSTXp1 SSTXn1 VBUS CC1 Pin # B12 B11 B10 B9 B8 Signal Name GND SSRXp1 SSRXn1 VBUS SBU2 A6 Dp1 B7 Dn2 A7 Dn1 B6 Dp2 A8 SBU1 B5 CC2 A9 VBUS B4 VBUS A10 SSRXn2 B3 SSTXn2 A11 SSRXp2 B2 SSTXp2 A12 GND B1 GND Note USB3CM: Support DP ALT mode and 5V@3A / 12V@3A output; USB 3.0 Dual Pin # Signal Name Pin # Signal Name 1 USB5V 10 USB5V 2 D- 11 D- 3 D+ 12 D+ 4 GND 13 GND 5 StdA_SSRX- 14 StdA_SSRX- 6 StdA_SSRX+ 15 StdA_SSRX+ 7 GND_DRAIN 16 GND_DRAIN 8 StdA_SSTX- 17 StdA_SSTX- 9 StdA_SSTX+ 18 StdA_SSTX+ Note Every on USB3.0 Power current provide 0.9A (Regular) USB 2.0 Dual 12 | Pin # Signal Name Pin # Signal Name 1 USB5V 1 USB5V 2 D- 2 D- 3 D+ 3 D+ 4 GND 4 GND Note Every on USB2.0 Power current provide 0.5A (Regular) Mini DP Pin # 1 3 5 7 9 11 13 15 17 19 Signal Name GND ML_Lane 0 (p) ML_Lane 0 (n) GND ML_Lane 1 (p) ML_Lane 1 (n) GND ML_Lane 2 (p) ML_Lane 2 (n) GND Pin # 2 4 6 8 10 12 14 16 18 20 Signal Name Hot Plug Detect CONFIG1 CONFIG2 GND ML_Lane 3 (p) ML_Lane 3 (n) GND AUX_CH (p) AUX_CH (n) DP_PWR DB9 for RS232 Pin # 1 3 5 7 9 Signal Name DCD SOUT GND RTS 0V / 5V/ 12V Max. current=1A Pin # 2 4 6 8 Signal Name SIN DTR DSR CTS 13 | 1.6 Package Overview Touch Computer Power Cord DC Power Supply Screw Stand Module (Optional) ! Warning! This product is intended to be supplied by a UL Listed Power Adapter, rated 24Vdc, 5A minimum. (complied with LPS or PS2) Tma = 40 degree C minimum, and the altitude of operation = 3048m minimum. If it needs further assistance with purchasing the power source, please contact to TES for further information. ! Mise en garde! Cet appareil est conçu avec une alimentation de courant CA, d'une tension nominale de 24Vdc, 5A minimum. (conforme au LPS ou PS2) Tma = 40 degrés C minimum et l'altitude de l'utilisation = 3048m minimum. Pour d'autres conseils pour l'installation de la source d'alimentation, communiquer avec TES pour de plus amples renseignements. 14 | Chapter 2 Product Installation 15 | 2.1 About VESA Mount The IC-156P-AW3 conform to the "VESA Flat Display Mounting Interface Standard" which defines a physical mounting interface for touch computer, and corresponding with the standards of touch computer mounting devices, such as wall-mounted. The VESA mount is located on the back of this unit. The IC-156P-AW2 may be wall mounted in the horizontal position (output connector facing down) or vertical position (output connector facing left or right). VESA Mount 16 | ! Warning! Please select the TES original screws! The distance between the back cover surface and the bottom of the screw hole is 8 mm. Please use four M4 / 8 mm screws diameter with proper length to mount your monitor. ! Mise en garde! Sélectionner les vis d'origine de TES! La distance entre la surface du couvercle arrière et le bas de l'orifice de la vis est de 8 mm. Utiliser quatre vis M4 de 8 mm de diamètre pour le montage de votre moniteur. 2.2 Power On / Off Switch Power On/Off Switch 17 | Function Power on Sleep Power off Force power off Description Press the power button. With OS settings, sleep or shut down choose one. Press the power button 4 sec. 2.3 Dimension 2.3.1 System Only Front View Side View 18 | Rear View Bottom View 2.3.2 System with Stand Front View 19 | Side View Rear View Bottom View 20 | 2.4 Optional Accessory Installation Note: Please install the accessories when the touch computer is in a powered off state 2.4.1 Install the Stand Place stand module on back of touch computer and align the screw holes. Install the four M4 screws to fasten the stand module. 2.4.2 Dismantle the Stand Step 1: Loosen the screws Step 2: Pull it out from touch computer and remove stand module. Step 2 Step 1 21 | 2.4.3 Install the Cables 2.4.4 Install the Camera Module Camera Module weight 19g Step 1: Remove the side cover. Step 2: Connect the camera module cable to the touch computer. Step 3: Install the two M3 screws to fasten the camera module. Step 1 Step 2 Step 3 22 | 2.4.5 Remove the Camera Step 1: Loosen the screws. Step 2: Remove the camera module cable from the touch computer. Step 3: Replace the side cover. Step 3 Step 2 Step 1 23 | 2.4.6 Install the MSR Module MSR Module weight 62g. Step 1: Remove the side cover. Step 2: Connect the MSR module cable to the touch computer. Step 1 Step 2 Step 3: The metal bracket hook into the gap between cover glass and bezel. 24 | Step 4: Install the two M3 screws to fasten the MSR module. Step 4 2.4.7 Remove the MSR Module Step 1: Loosen the screws. Step 1 25 | Step 2: Remove the MSR module cable from the touch computer. Step 3: To assemble the side cover. Step 3 Step 2 26 | Appendix 27 | Declaration of the Presence Condition of the Restricted Substances Marking IC-156P-AW3 Equipment name: Touch Computer Type designation (Type): IC-156P-AW3 Restricted substances and its chemical symbols Unit Plastic Parts Metal Parts Cable component LCD Panel Touch Panel PCBA () Software Lead Mercury Cadmium Hexavalent (Pb) (Hg) (Cd) chromium (Cr+6) Polybrominated biphenyls (PBB) Polybrominated diphenyl ethers (PBDE) Note 1Exceeding 0.1 wt %andexceeding 0.01 wt %indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. Note 2indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. Note 3The-indicates that the restricted substance corresponds to the exemption. 28 |Adobe PDF Library 21.11.71