Introduction
This guide provides comprehensive information for the setup, configuration and maintenance of the C200 Scanning - Dimensioning device. It contains shortcuts for end users, configuration barcodes for system management, communication options, data and transmission formats, dimensioning units and output, and supported software information.
Also available for download at www.cubetape.com/support is the scan engine parameter programming guide which provides complete guidance to programming the scan engine to meet specific symbology requirements.
Factory Default Settings
| Settings | Factory Defaults |
|---|---|
| Communication Mode | HID over wireless 2.4G using dongle |
| Keyboard | English |
| Workflow | Single Item (1DIM) |
| Suffix for Dimensional Items | TAB |
| Suffix for General Items | TAB |
| Source Prefix | OFF |
| Units | inches |
| Output | Nearest inch |
| Sleep Time | 10 minutes |
| LED Aimer | ON at Read |
| Tape Cassette | 16ft/5m with QR symbology |
Communication and Pairing Options
Barcodes and dimensions captured on C200 can be sent to a connected system using one of the following methods:
- Windows connection using wireless USB dongle
- Windows or Android connection using Bluetooth Direct (HID) Mode
- Windows or Android connection using Bluetooth Application (SPP) Mode
- Apple iOS connection using Bluetooth BLE Mode.
C200 ships with two other pairing utilities to simplify the pairing process:
NFC Pairing: Initiated when a user brings the NFC Reader of their mobile device into close proximity with the C200 scan head. Follow the Android prompts to complete pairing.
Scan to Pair: Initiates pairing when C200 scans a pairing barcode displayed on the mobile device screen. This option may need to be co-ordinated with 3rd party software vendors.
Behaviour
1. LED
Description of the basic functions of the indicator LED:
| LED | Description |
|---|---|
| Blue LED | Connection Status: ON when connected, OFF when disconnected |
| Green LED | Decode Indicator: Flashes once on successful data scan and transmission, Flashes three times if scanning is successful but transmission fails |
| Red LED | Charge Indicator: ON when charging, OFF when fully charged or not charged |
Indicator LED combination description:
| LED | Description |
|---|---|
| Blue LED OFF, Green LED flashes | 2.4G mode pairing status |
| Green LED OFF, Blue LED flashes | SPP mode pairing status |
| Green and Blue LED flash alternately | HID mode pairing status |
2. Buzzer
| LED | Description |
|---|---|
| Long beep (low followed by high frequency) | Power is ON |
| Long beep (high followed by low frequency) | Power is OFF |
| Short beep (low frequency) | Indicates bar code is read, or pairing is successful |
| Short beep (high followed by low frequency) | Configuration setting success |
| Three short beeps (low frequency) | Wireless transmission failed |
| Two short beeps (low frequency) | Wireless connection disconnect |
| Two short beeps (high frequency) | Configuration setting failure |
3. Button
| LED | Description |
|---|---|
| Button | Short press to power ON. Hold down the button for 8 seconds to enter Bluetooth HID pairing. When pairing, double-click to end pairing. |
System Options
About Bluetooth Version
Output Bluetooth version information
[QR code for Bluetooth Version]
About Scanner Version
Output scan module version information
[QR code for Scanner Version]
Configuration Disable
Prevent device reconfiguration
[QR code for Config Disable]
Configuration Enable
Allow device reconfiguration
[QR code for Config Enable]
Scan Count
Output scanner count
[QR code for Scan Count]
Restore Scanner Defaults
Reset scanner to factory defaults
[QR code for Scanner Defaults]
Restore Wireless Defaults
Reset wireless comms to factory defaults
[QR code for Wireless Defaults]
Output Battery Level
Output Battery Level
[QR code for Battery Level]
Connect Options
2.4G Communication Mode
Set communication mode to wireless 2.4G using dongle
[QR code for 2.4G]
2.4G Application (COM) Mode
Configures 2.4G Wireless dongle as a USB Serial device. Requires a connection for reconfiguration
[QR code for 2.4G App (COM)]
2.4G Direct (HID) Mode
Configures 2.4G Wireless dongle as a USB HID device. Requires a connection for reconfiguration
[QR code for 2.4 Direct (HID)]
Bluetooth Direct Mode (HID)
Set communication mode to Bluetooth Application Mode (HID)
[QR code for BT Direct (HID)]
Bluetooth Application Mode (SPP)
Set communication mode to Bluetooth Application Mode (SPP)
[QR code for BT App (SPP)]
Communication Pair
Scan this barcode before inserting RF dongle in spare USB port to connect to PC. Press the button twice to exit pairing mode
[QR code for Pair]
Bluetooth Low Energy Mode (BLE)
Set communication mode to Bluetooth Low Energy (BLE)
[QR code for 2.4G]
Other Device Settings
LED Aimer ON Always
[QR code for LED on Always]
LED Aimer OFF
[QR code for LED off]
LED Aimer ON at Read
[QR code for LED On at Read]
Keyboard English
Sets Keyboard to English when in 2.4G and Bluetooth Direct (HID) mode
[QR code for KBD English]
Keyboard French
Sets Keyboard to French when in 2.4G and Bluetooth Direct (HID) mode
[QR code for KBD French]
Keyboard German
Sets Keyboard to German when in 2.4G and Bluetooth Direct (HID) mode
[QR code for KBD German]
Keyboard Italian
Sets Keyboard to Italian when in 2.4G and Bluetooth Direct (HID) mode
[QR code for KBD Italian]
Keyboard Japanese
Sets Keyboard to Japanese when in 2.4G and Bluetooth Direct (HID) mode
[QR code for KBD Japanese]
Keyboard Spanish
Sets Keyboard to Spanish when in 2.4G and Bluetooth Direct (HID) mode
[QR code for KBD Spanish]
Sleep in 1 min
Set sleep time to 1 minute
[QR code for Sleep 1min]
Sleep in 5 min
Set sleep time to 5 minutes
[QR code for Sleep 5min]
Sleep in 10 min
Set sleep time to 10 minutes
[QR code for Sleep 10min]
Sleep in 30 min
Set sleep time to 30 minutes
[QR code for Sleep 30min]
Sleep in 30s
Set sleep time to 30 seconds
[QR code for Sleep 30sec]
Sleep Never
Set sleep time to never
[QR code for Sleep Never]
Sleep Now
Set sleep time to sleep immediately
[QR code for Sleep Now]
Sound ON
[QR code for Sound On]
Sound OFF
[QR code for Sound Off]
Dimensioning Units and Output
Output Nearest 0.5
Output dimensions to the nearest half
[QR code for Output 0.5]
Output Nearest 1
Output dimensions to the nearest whole number
[QR code for Output Nearest 1]
Output Next 1
Output dimensions to the nearest whole number
[QR code for Output Next 1]
Units = cm
Set units to centimetres
[QR code for Units cm]
Units = in
Set units to inches
[QR code for Units in]
Units = m
Set units to metres
[QR code for Units m]
Suffixes and Prefixes
Prefix Disable
Disable use of prefix
[QR code for Prefix Disable]
Prefix Enable
Enable use of prefix
[QR code for Prefix Enable]
Prefix DIM ~
Set DIM prefix to ~
[QR code for Prefix Dim ~]
Prefix GEN ^
Set GEN prefix to ^
[QR code for Prefix Gen ^]
Suffix DIM CR
Set suffix to CR for dimensional items
[QR code for Suffix Dim CR]
Suffix DIM TAB
Set suffix to TAB for dimensional items
[QR code for Suffix Dim TAB]
Suffix Disable
Disable use of suffix
[QR code for Suffix Disable]
Suffix Enable
Enable use of suffix
[QR code for Suffix Enable]
Suffix GEN CR
Set suffix to CR for general items
[QR code for Suffix Gen CR]
Suffix GEN TAB
Set suffix to TAB for general items
[QR code for Suffix Gen TAB]
Batch and Online Modes
Clear Data Mode
Clear stored data when in storage (offline) mode
[QR code for Clear Data]
Data Upload Mode
Upload data when in storage (offline) mode
[QR code for Upload Data]
Display Record Number Mode
Output number of stored record when in storage (offline) mode
[QR code for Display Record#]
Real Time Mode
Send data in real time
[QR code for Real Time Mode]
Batch Mode
Store data for later upload
[QR code for Batch Mode]
Workflow and Process Options
Off Floor OFF
Remove off floor offset to next measurement
[QR code for Off Floor OFF]
Off Floor ON
Add off floor offset to next measurement
[QR code for Off Floor ON]
Set One Time Offset TC2-50
Set off floor value for TC2-50
[QR code for Set Offset 5m]
Set One Time Offset TC5-75
Set off floor value for TC5-75
[QR code for Set Offset 7.5m]
Set Spacer to x
Set Spacer to lower case x
[QR code for Spacer x]
Set Spacer to X
Set Spacer to upper case X
[QR code for Spacer X]
Workflow 1DIM
Set workflow to single item (1DIM)
[QR code for Workflow 1DIM]
Workflow 3DIM
Set workflow to three item (3DIM)
[QR code for Workflow 3DIM]
Workflow 3DIM+
Set workflow to three item LFT
[QR code for Workflow 3DIM+]
Disclaimer
[CubeTape Logo]
Disclaimer © 2023 ParcelTools Pty Ltd.
All rights reserved. Please read through the manual carefully before using the product and operate it according to the manual. It is advised that you should keep this manual for future reference. Do not disassemble the device or remove the seal label from the device, doing so will void the product warranty provided by ParcelTools.
All pictures in this manual are for reference only and actual product may differ. Regarding to the product modification and update, ParcelTools have the right to make changes to any software or hardware to improve reliability, function, or design at any time without notice. The information contained herein is subject to change without prior notice.
The products depicted in this manual may include software copyrighted by ParcelTools or a third party. The user, corporation or individual, shall not duplicate, in whole or in part, distribute, modify, decompile, disassemble, decode, reverse engineer, rent, transfer or sublicense such software without prior written consent from the copyright holders.
Specifications correct at time of printing.
[Australian Made Logo]
www.cubetape.com
