HELTEC AUTOMATION HT-H7608 Wi-Fi HaLow Router Instruction Manual

Instruction Manual for HELTEC AUTOMATION models including: HT-H7608, HT-H7608 Wi-Fi HaLow Router, Wi-Fi HaLow Router, HaLow Router, Router

User Manaul

Heltec Automation Technology Co., Ltd HT-H7608 Wi-Fi HaLow Router 2A2GJ-HT-H7608 2A2GJHTH7608 ht h7608

File Info : application/pdf, 16 Pages, 1.82MB

GetApplicationAttachment.html?id=8306304

HT-H7608 Wi-Fi HaLow Router

https://heltec.org

Documents

Rev. 1.0

P 1/16

May 2023

Heltec Automation © Limited standard files

Document version

Version

Time

Rev. 1.0

2024-9-16

Description Preliminary version

Remark Richard

Copyright Notice
All contents in the files are protected by copyright law, and all copyrights are reserved by Chengdu Heltec Automation Technology Co., Ltd. (hereinafter referred to as Heltec). Without written permission, all commercial use of the files from Heltec are forbidden, such as copy, distribute, reproduce the files, etc., but non-commercial purpose, downloaded or printed by individual are welcome.

Disclaimer
Chengdu Heltec Automation Technology Co., Ltd. reserves the right to change, modify or improve the document and product described herein. Its contents are subject to change without notice. These instructions are intended for you use.

https://heltec.org

Documents

Rev. 1.0

P 2/16

May 2023

Heltec Automation © Limited standard files

Content
HT-H7608 ..................................................................................................................1 Document version..................................................................................................2 Copyright Notice ....................................................................................................2 Disclaimer ............................................................................................................... 2 Content................................................................................................................... 3 1. Description.............................................................................................4 1.1 Overview................................................................................................................. 4 1.2 Product Features ......................................................................................................... 5 1.3 Application................................................................................................................... 6 2. Specifications.......................................................................................7 2.1 Generic Parameter ...................................................................................................... 7 2.2 Wi-Fi HaLow parameters ............................................................................................. 8 2.3 Power consumption .................................................................................................... 8 2.4 RF Specifications .......................................................................................................... 9 2.5 Channel&Bandwidth.................................................................................................. 10 2.6 RGB status indicator description ............................................................................... 10 2.7 Button description..................................................................................................... 11 3. Get Started ..........................................................................................12 3.1 Installation bracket.................................................................................................... 12 3.2 Hardware Connection................................................................................................ 12 3.3 Setup guide................................................................................................................ 13 4. Hardware Dimensions....................................................................14 5. Resource ...............................................................................................15 6. Heltec Contact Information ........................................................15

https://heltec.org

Documents

Rev. 1.0

P 3/16

May 2023

Heltec Automation © Limited standard files

7. FCC Statement ...................................................................................15
1. Description 1.1 Overview
HT-H7608 is an innovative WiFi HaLow gateway from Heltec Automation designed to meet the needs of long-distance/high-speed data transmission for IoT applications. The gateway uses WiFi HaLow(IEEE 802.11ah) technology that operates in the sub-1 GHz unlicensed band, which has stronger penetration and larger coverage compared with the traditional WiFi standard. H7608 is equipped with powerful hardware including advanced RF capabilities, high-performance MCU, and flexible interfaces for seamless integration with existing networks. It can be easily configured and OTA upgraded through web UI, and supports the simultaneous connection of a large number of devices, which making it a great solution for intelligent manufacturing, intelligent agriculture and smart city, etc.

https://heltec.org

Documents

Rev. 1.0

P 4/16

May 2023

Heltec Automation © Limited standard files

1.2 Product Features
Wi-Fi and Ethernet supported, WiFi HaLow and 2.4GHz dual-band design. Long-range transmission capability, the range can reach 1km and further
within the visual distance. Supports access to a large number of devices, more than 4 times that of
traditional Wi-Fi access points. High transmission speed, it maintains 150Kbps at the limit distance and
32Mbps at close distances. Flexible networking methods, including AP, STA, Mesh, etc. Easy setup and OTA upgrade via the Web UI. Light and stylish wall-mounted, simple to install. -20°C to 70°C maximum operating temperature range.

https://heltec.org

Documents

Rev. 1.0

P 5/16

May 2023

Heltec Automation © Limited standard files

1.3 Application
Wi-Fi HaLow technology is suitable for most IoT scenarios, especially those that require high-speed transmission. Here are some common application scenarios. If you have any questions or customization requirements, please feel free to contact us.
Remote camera monitoring Industrial automation control Asset management and tracking Old device Information upgrade Smart Home Smart City Wi-Fi/Ethernet/Wi-Fi_HaLow extension and bridging WiFi-HaLow Gateway Proximity sensors Rural internet access LAN construction Network blind spot coverage

https://heltec.org

Documents

Rev. 1.0

P 6/16

May 2023

Heltec Automation © Limited standard files

2. Specifications

2.1 Generic Parameter
Parameters Wi-Fi chip Wi-Fi HaLow chip Wi-Fi HaLow
Wi-Fi Flash RAM Power Supply Power Consumption Operating temperature Operating humidity
Interface
Dimensions Weight

Table 2.1 General specification

Description

MT7628NN

MM6108IQ

IEEE 802.11ah

IEEE 802.11 b/g/n

32M

128M

5V DC

Table 2.3 -20 ~ 70 10%90%, no-condensing

USB Type-C

Power/Ethernet

DC-031A

Power Supply

RJ45

Ethernet

109*66*30.50 mm
65g(excluding antenna

https://heltec.org

Documents

Rev. 1.0

P 7/16

May 2023

Heltec Automation © Limited standard files

2.2 Wi-Fi HaLow parameters

Table 2.2 Wi-Fi HaLow Parameters

Parameter

Description

Chip

MM6108IQ

Wi-Fi Standard

IEEE 802.11ah

Frequency Max. output power

902-928 MHz 19±1dBm

Channel Bandwidth

1/2/4/8 MHz(see table2.5)

Data Rate

32.5 Mbps @ 8 MHz or 15 Mbps @ 4 MHz

Antenna connector

SMA

2.3 Power consumption

Mode

Min

Configuration

NONE

Ethernet

2.4G Wi-Fi

STA

Mesh Point

Mesh Gate

Table2.3 Power consumption

Typical

Max

Units

295

296

225

230

205

302

264

https://heltec.org

Documents

Rev. 1.0

P 8/16

May 2023

Heltec Automation © Limited standard files

2.4 RF Specifications 2.4.1 Receiver sensitivities

Table2.4.1 Receiver sensitivities

Minimum Receive sensitivity (dBm) per BW

1 MHz -105 -102 -99 -96

2 MHz -103 -100 -97 -94

4 MHz -101 -97 -95 -91

8 MHz -97 -93 -91 -88

-93

-90

-88

-85

-89

-87

-84

-80

-88

-85

-83

-79

-87

-84

-81

-77

-107

N/A

2.4.2 Transmitter power

TX output power(1,2MHz BW) MCS 0 MCS 7

Min(dBm) 18 16

Table2.4.2 Transmitter power

Typical(dBm) Max(dBm)

18.5

TX output power(4MHz BW) MCS 0 MCS 7

Min(dBm) 15 13

Typical(dBm) Max(dBm)

https://heltec.org

Documents

Rev. 1.0

P 9/16

May 2023

Heltec Automation © Limited standard files

TX output power(8MHz BW) MCS 0 MCS 7

Min(dBm) 17 15

Typical(dBm) Max(dBm)

2.5 Channel&Bandwidth

Table2.5 Channel&Bandwidth

Bandwidth(MHz) Channel&Frequency(MHz)

3(903.5), 5(904.5), 7(905.5), 9(906.5), 11(907.5), 13(908.5), 15(909.5),

17(910.5), 19(911.5), 21(912.5), 23(913.5), 25(914.5), 27(915.5), 29(916.5), 1
31(917.5), 33(918.5), 35(919.5), 37(920.5), 39(921.5), 41(922.5), 43(923.5),

45(924.5), 47(925.5), 49(926.5)

6(905), 10(907), 14(909), 18(911), 22(913), 26(915), 30(917), 34(919), 2
38(921), 42(923), 46(925)

8(906), 16(910), 24(914), 32(918), 40(922)

12(908), 28(916), 44(924)

2.6 RGB status indicator description

Table2.6 RGB Status Indicator Description

Color

Status

Description

Red Green

Always on/Blinking System booting

Blinking

Getting IP address AP/Mesh-gateway , @RJ45 HaLow connecting(STA/Mesh-Point, @RJ45)

https://heltec.org

Documents

Rev. 1.0

P 10/16

May 2023

Heltec Automation © Limited standard files

Always on Blinking

Geted IP addressAP/Mesh-gateway , @ RJ45 Halow connected(STA/Mesh-Point, @RJ45) Getting IP address AP/Mesh-gateway , @USB HaLow connecting(STA/Mesh-Point,

@USB)

Blue

Geted IP addressAP/Mesh-gateway ,

Always on

@ USB Halow connected(STA/Mesh-Point,

@USB)

Yellow

Light up and release Enter Configuration mode

White

Light up and release Factory reset

Yellow-Green Alternate flicker Configuration mode

Yellow-Blue Alternate flicker Configuration mode

Purple

Blinking

Button pressed

2.7 Button description

When the button is successfully pressed, the device indicator will appear a purple light,

and then the corresponding status indicator will appear.

Table2.6 Button description

Status

Description

Single press

Switch network connection mode. The switch is green when

In AP mode, after the connection network successfully. In STA mode, after obtaining the IP (regardless of whether the network is successfully connected). In AP mode, after the connection network successfully. In STA mode, after obtaining the IP (regardless of whether the network is successfully connected).

https://heltec.org

Documents

Rev. 1.0

P 11/16

May 2023

Long press 3 seconds Long press 10 seconds

connected to RJ45, blue when connected to USB Yellow light is on, the device enters configuration mode White light is on, factory reset

3. Get Started

3.1 Installation bracket
Tighten the bracket with screws Insert gateway into bracket from top to bottom

3.2 Hardware Connection
Plug in the power adapter, at this time the device RGB light is red. Power adapter Specifications:5V/1A

https://heltec.org

Documents

Rev. 1.0

P 12/16

May 2023

Connect the Antenna. The interface specification: SMA.

3.3 Setup guide
Please refer to the Heltec documentation page for detailed configuration methods.

https://heltec.org

Documents

Rev. 1.0

P 13/16

May 2023

4. Hardware Dimensions

https://heltec.org

Documents

Rev. 1.0

P 14/16

May 2023

5. Resource
Documents Page: Heltec Products Operation Documention Resource station: resource.heltec.cn

6. Heltec Contact Information
Heltec Automation Technology Co., Ltd Chengdu, Sichuan, China Email: support@heltec.cn Phone: +86-028-62374838 https://heltec.org

7. FCC Statement

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

https://heltec.org

Documents

Rev. 1.0

P 15/16

May 2023

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. To assure continued compliance, any changes or modifications not expressly approved by the party. Responsible for compliance could void the user's authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices). This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: The equipment complies with FCC Radiation exposure limits set forth for uncontrolled enviroment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

https://heltec.org

Documents

Rev. 1.0

P 16/16

May 2023

References

Microsoft Word 2016 Microsoft Word 2016