User Manual for IGS models including: SPC-100 Industry Gas Spring, SPC-100, Industry Gas Spring, Gas Spring

Air Watcher Manual R1.0

IGS

Users Manual

SEMES SPC-100 2AN5B-SPC-100 2AN5BSPC100 spc 100


File Info : application/pdf, 10 Pages, 558.66KB

PDF preview unavailable. Download the PDF instead.

GetApplicationAttachment.html?id=6710139
SPC-100

Rev.01

USER MANUAL

Product Overview

1-1. Characteristic
 Real-time particle monitoring and control  Precision measurement and long-term stability  0.3, 0.5, 1.0, 2.5, 5.0, 10.0 6-CH particle monitoring  268 * 128 mono graphic LCD applied  Simultaneous display of particle, temperature and humidity measurements  RS485 communication (Modbus RTU)  WI-Fi communication Station Mode : TCP/IP, Wi-Fi(2.4GHz) communication support
1-2. Applications
 Semiconductor cleanroom particle, temperature, humidity measurements  Particle, temperature and humidity measurement in pharmaceutical and hospital cleanroom  Various semiconductor equipment  IAQ (Indoor Air Quality) monitoring and control device for home and industrial  Home and industrial air conditioner

1-3. Specifications
Model
Operating Voltage Current consumption
Operating principle Measurement particle size range Measurement range Counting efficiency Temperature measuring range Humidity measuring range
Wi-Fi output Protocol Digital Output RF frequency bands Maximum RF output power
Operating Temperature Storage Temperature
Dimension ( W*H*D) Weight

SPC-100
12Vdc ±10% (DC Adapter plug: inner diameter 2.1, outer diameter 5.5PIE) Max. 350mA @ 12Vdc
Laser scattering >0.3, >0.5, >1.0, >2.5, >5.0, >10 0 ~ 10,000,000 pcs/L (1pcs/L = 28.3pcs/cf) 50%@0.3m , 100%@>0.5m ( 0°C ~ 40°C, 50 ±10%RH ) -40 ~ +125 / ±1 0 ~ 100% / ±5.0%
Station Mode (TCP/IP Communication) RS485 Modbus
WLAN: 2412-2472 MHz / BLE: 2402-2480 MHz WLAN: 19.8 dBm / BLE: 9.8 dBm
10... +60 0... +70
110*185*44.3 (Wi-Fi Without Antenna) 387g

Product Function and How To Use
Operating configuration

KEY
M

KEY Name
UP KEY DOWN KEY MENU KEY ENTER KEY

Description
Move up and increase value Move down and decrease value
Enter configuration mode Enter

Configuration Mode

Configuration Mode

 Sensor display Settings

Equipment Settings



Sensor Alarm Settings



Wi-Fi Settings



 Sensor Display Settings
Particle size range setting displayed on the initial screen
 Equipment Settings
Equipment Default Settings.

 Sensor Alarm Settings
Set an alarm for each Particle Size Range.

Click the MENU button to enter configuration mode.

 Wi-Fi Settings
Settings required for Wi-Fi communication.

Product Function and How To Use
Sensor Display Settings

Configuration Mode Sensor Display Settings Equipment Settings Sensor Alarm Settings Wi-Fi Settings

Sensor Display Settings

Left Upper

0.3 um

Right Upper

0.5 um

Left Lower

1.0 um

Right Lower

2.5 um

Click the ENTER button to enter Sensor Dispalys Settings.
Equipment Settings
Configuration Mode Sensor Display Settings Equipment Settings Sensor Alarm Settings Wi-Fi Settings

Particle size range setting displayed on the initial screen

Equipment Settings

Language Settings

English

Equipment ID

1

Baud Rate

115200bps

temperature unit



Click the ENTER button to enter Equipment Settings.

Equipment Default Settings.

Product Function and How To Use
Sensor Alarm Settings

Configuration Mode Sensor Display Settings Equipment Settings Sensor Alarm Settings Wi-Fi Settings

Sensor Alarm Settings

0.3 um Upper Limit

0

0.3 um Lower Limit

0

0.5 um Upper Limit

0

0.5 um Lower Limi

0

Click the ENTER button to enter Sensor Alarm Settings.
Wi-Fi Settings
Configuration Mode Sensor Display Settings Equipment Settings Sensor Alarm Settings Wi-Fi Settings

Set an alarm for each Particle Size Range.

Wi-Fi Settings

AP IP (1)

192

AP IP (2)

168

AP IP (3)

000

AP IP (4)

002

Click the ENTER button to enter Wi-Fi Settings.

Settings required for Wi-Fi communication.

 When using Wi-Fi mode, RS485 communication is not available.

Product Connector Specifications
Connector Specifications

Communication Connector Power Connector

RJ-45 8p8c (Dual)

2.0PIE DC JACK (12V)

Communication Connector Pin Map Specification

No

Pin Assigned

1

RS485-

2

RS485+

3

GND

4

GND

5

NC

6

NC

7

NC

8

NC

Product Appearance
Product Dimensions

Communication Connector

<UP>

Power Connector Wi-Fi Antenna
Vent Hole

< Left Side >

<Front>

<DOWN>

D/L Connector Dust Outlet
Dust Inlet <Right Side>
Status LED

<Rear>

Products handling precaution
 There is a risk of electric shock to this product, so do not open the product while power is applied.
 Be sure to install this product on a fixed location such as a rack or panel.
 Do not touch the power plug with wet hands. It may cause electric shock or injury.
 Supply the power input within the specified rating range.
 Be careful not to let water or beverages enter the product.
 Clean regularly with a soft cloth or brush. If the dust inlet and outlet are blocked, it may cause product failure.
 To prevent inductive noise, separate wiring from high-voltage lines and power lines.
 Avoid installation in places subject to strong magnetism, noise, vibration and impact.
 When extending the sensor wire, use a shield wire and do not make it unnecessarily long.
 Sensor wire and signal wire should be wired independently away from power, power and load wires.
 Avoid using near devices that generate strong high-frequency noise (high-frequency welding machine, high-frequency sewing machine, high-frequency radio, large-capacity SCR controller).
 Some measurement errors may occur depending on the usage environment and usage method.
 Do not disassemble the product arbitrarily. (Warranty does not apply to products that have been disassembled.)
 We are not responsible for product damage outside of the warranty conditions specified by the manufacturer.
 It is recommended to calibrate once a year because it can be affected by factors such as temperature, humidity, and shock during the long-term use period.
 Be sure to observe the contents specified in the handling precautions above as they may cause product failure.
 The specifications and dimensions described in this user manual are subject to change without notice for improvement.

FCC Instructions
FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body.

This document contains information of products and processes in development. All information provided here is subject to change without notice. Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
We do not guarantee the performance of this device in case of disassembling, operating without complying with instructions in this document.
Contact your IGS representative to obtain the latest forecast, schedule and specifications. Or It may be obtained by calling +82-2-6299-7536~7 or by visiting http://www.igstech.kr
Copyright © 2023 IGS Incorporated. All rights reserved.



References

Adobe PDF Library 15.0