Juniper | Office Furniture for the Entire Workspace
Installation Guide for Juniper models including: S1, S2, S3, THREE60 Conference Table, THREE60, Conference Table, Table
Install Guides | Juniper Office Furniture
File Info : application/pdf, 24 Pages, 1,007.54KB
DocumentDocumentTHREE60 Conference Table Includes Add-Ons: S1 | S2 | S3 General Installation Guide TABLE OF CONTENTS Sections S1 :: Sitting Height ..................................................................................... 1 S2 :: Standing Height .............................................................................. 9 S3 :: Optional Power.............................................................................. 15 S1: Sitting Height Overview THREE60 Conference Table Quantities are for a 48" x 216" table, parts may vary depending on project, but install steps will remain same. 1 SITTING HEIGHT Parts List Code Qty. Description GCNAB 2 Angled Sleigh Leg 1 Trapezoid Surface CNS48144 2 In-Surface Grommet CNCGB 2 Center Grommet Spacers 2 In-Surface Grommet CNCBV2 4 BFB1 6 GCNABCOV* 4 Cabinet Base Flat Bracket Covered Leg *If applicable. 2 SITTING HEIGHT 1 | Prepare Surface and Measure for Legs Carefully place surface upside-down on floor, a cushioned area is preferred. Measure 12" from surface edge and center-align to determine leg placement. NOTE: Same process for square-ended table. 12" 2 | Secure Angled Sleigh Legs Follow measurements and insert screws per leg through metal plate and into laminate surface. 3 SITTING HEIGHT 3 | Measure for Cabinet Base or Covered Leg Place cabinet base, or covered leg, centered under table grommet cutouts. 5.91" 9.45" 9.45" 5.12" 4 SITTING HEIGHT 4 | Install Cabinet base or covered Leg Insert 4 screws per base through laminate top into bottom of surface. 5 | Attach Hardware to Surface Edge Insert 2 wooden dowels, attach 2 flat brackets, and connect 4 sets of joint fasteners to one side of each surface edge. Surface Edge 5 SITTING HEIGHT 6 | Flip and Assemble Flip each piece over so that it is standing on a leg/cabinet base. Align open holes on surface edge with wooden dowels and threaded rods on other surface edge. 7 | Fully Secure Hardware 1. Set Hardware Turn to Tighten 2. Tighten Hardware Hold Still 6 SITTING HEIGHT 8 | Install Grommets Insert wire management grommet. 7 8 END OF SITTING HEIGHT SECTION S2: Standing height Overview THREE60 Conference Table All parts listed are for a single standing height table; additional parts will be needed for additional standing height table. 9 STANDING HEIGHT Parts List Code Qty. Description GCNABSH 2 Standing Height Angled Sleigh Leg CNS4896 1 Main Surface 1 In-Surface Grommet GCNABSHLE 2 Support Brace BFB1 2 Flat Brackets 10 STANDING HEIGHT 1 | Prepare Surface Carefully place surface upside-down on floor, a cushioned area is preferred. Measure 12" from surface edge and center-align to determine leg placement. Attach 2 flat brackets on center seam of table. NOTE: Leg placement may need to be adjusted based on surface size. 12" 2 | Install Angled Sleigh Legs Follow measurements and insert 15 screws per leg through metal plate and into laminate surface. 11 STANDING HEIGHT 3 | Install Support Brace 4 | Flip and Insert Grommet Insert wire management grommet. Note: See page 13 for optional covered sleigh leg. See page 15 for power module install. 12 STANDING HEIGHT Optional Covered Sleigh Leg All steps for installation are the same. However, leg will be aligned with grommet cutout on the table. NOTE: Covered sleigh leg is optional for wire management. 9.45" 5.12" 13 14 END OF STANDING HEIGHT SECTION S3: Optional Power Overview THREE60 Conference Table 15 OPTIONAL POWER Parts List Code Qty. BPCONF2V2 or BPCONF3 1 Description In-Surface Power Module JC1 5 J-Clips VB24 1 Cable Vertebrae 16 OPTIONAL POWER 1 | Attach Metal Clips and Insert into Surface Attach 2 metal clips to back of module base then insert into pre-cut holes in surface. 17 OPTIONAL POWER 2 | Secure Module into Place Insert plastic clamps into holes on bottom of module. Rotate and then push against surface to clamp module into place. 1. Clamp 2. Rotate 3. Push 18 OPTIONAL POWER 3 | Optional Power Vertebrae Attach vertebrae to underside of top panel. Insert wood screws through top bracket and into laminate panel. NOTE: Power vertebrae will be mounted adjacent to power module. 19 20 END OF OPTIONAL POWER SECTION 1-866-999-0955 | hello@juniperoffice.com | juniperoffice.com © 2023 Juniper Office | Version 23.0.0