Emergency Bulkhead Exit Light

Important Safety Information

❗ IMPORTANT: These instructions are for your safety. Please read through them thoroughly prior to handling the product and retain them for future reference.

• Do not use with a dimmer switch. ??
• All fittings must be installed by a competent person in accordance with local regulations (IET wiring regulation BS7671).
• Check the pack and ensure all parts listed are present.
• Remove all packaging before use.
• Decide on the appropriate location for your product.
• CAUTION: IP66 is guaranteed when the product is properly installed and sealed.
• Avoid locating the product in a corrosive environment.
• Always refer to the installation drawing for product orientation.
• Securely fix the product to the mounting surface using the supplied screws and wall plugs (suitable for masonry only). Other fixings must be purchased separately.
• Take care not to drill into any pipes or mains cables beneath the surface during mounting hole preparation.
• IMPORTANT: The fixing point(s) must be capable of supporting the full weight of the light fitting.
• Wiring diagrams are for reference only. Always refer to terminal markings. Ensure all electrical connections are tight and no loose strands are present.
• Never place or hang anything on the product.
• Never use terminal cables to support the product's weight.
• If the product does not light after installation: Ensure power is supplied and all connections are secured.
• If in doubt about installation or use, consult a qualified electrician.
• Always disconnect the product from mains for at least 10 minutes to allow it to cool down before maintenance or adjustment.
• Regular care and maintenance are recommended to keep the surface condition well.

Parts Included

• Part 01: x1
• Part 02: x1
• Part 03: x1
• Part 04: x4
• Part 05: x4
• Part 06: x4
• Part 07: x1

Tools Required

• Drill
• Screwdriver
• Appropriate fixings (if not suitable for your mounting surface)

Technical Data

Guarantee

This product is covered by a 7-year manufacturer's guarantee (4 years for the battery pack) against manufacturing defects from the date of purchase or delivery, for normal use. To make a claim, you must present proof of purchase. This guarantee applies only to new products and not to second-hand or display items. Any replacement product will only be guaranteed until the expiry of the original guarantee period. The guarantee covers product failures and malfunctions provided the product is used for its intended purpose and is installed, cleaned, and maintained according to the information in these terms, the user manual, and standard practice. It does not cover defects or damage caused by normal wear and tear, improper use, faulty installation or assembly, neglect, accident, misuse, or modification. Ancillary costs (shipping, labour, etc.) and indirect damage are not covered. Rights under this guarantee are enforceable in the country of purchase and are in addition to your statutory rights.

Installation Instructions

Follow these steps carefully for installation:

Step 01: Mounting Preparation

Ensure the power supply is turned OFF before commencing. Decide on the mounting location. If mounting on a surface other than masonry, appropriate fixings must be purchased and used. Prepare mounting holes as required (e.g., Ø20 mm for cable entry).

Step 02: Fixing the Product

Securely fix the product to the mounting surface using the supplied screws and wall plugs (suitable for masonry). Ensure the chosen fixing points can support the full weight of the light fitting.

Step 03: Wiring

Refer to the terminal markings on the product for correct wiring. Ensure all electrical connections are tight and that no loose strands are left exposed. The wiring diagram provided is for reference only.

Step 04: Securing the Product

Complete the mounting process by securing all components as shown.

Step 05A: Back Entry

Utilize the back entry for cable management as illustrated.

Step 05B: Side Entry

Use the side entry for cable management, ensuring correct torque is applied (5.5 Nm) where specified.

Step 05C: Besa Box Mounting

The product can be mounted using a Besa Box with 50.8 mm fixing centres.

Step 06: Wiring Terminations

For Non-Maintained Operation: Connect Neutral (N), Line (L), and CPC (E) for continuity.

For Maintained Operation: Connect Neutral (N), Line (L), and CPC (E) for continuity.

For Maintained (Switchable) Operation: Connect Neutral (N), Switched Line (Ls), Line (L), and CPC (E) for continuity.

Wire colour coding: L = Brown or Red, N = Blue or Black, E = Green/Yellow.

Use cables with a cross-section of 1.0-2.5 mm² and a diameter of Ø6-12 mm.

Step 07-08: Further Connections

Continue with the remaining wiring and connection steps as depicted in the diagrams.

Step 09: Test Button

Locate the TEST BUTTON for performing function and duration tests.

Step 10: Final Connections

Complete all final electrical connections to the luminaire.

Emergency Exit Light Pictograms

The luminaire is designed for wall mounting and includes pictograms for emergency exit indication. These are typically displayed within a 100 mm x 100 mm area for clear visibility.

Care & Maintenance

Battery Replacement

The battery type is 1 x 3.2 V 1500 mAh 18650 LiFePO4. It is crucial to replace the battery only with the same or an equivalent type.

1. Disconnect the battery from the converter.
2. Remove the old battery.
3. Install the new battery.
4. Connect the new battery to the converter.

Self-Test and Testing Record

The luminaire is equipped with an automatic self-test function. A weekly 1-minute function test checks battery connection and LED module integrity. A yearly 3-hour duration test also verifies battery and LED module connections. A manual test button is available for on-demand inspection.

Test Button Operation:

• Press for <2 seconds: Simulates emergency mode.
• Press for 3-5 seconds: Starts a duration test manually. The test can be aborted by pressing the OFF button (1-2 seconds).
• Press for 5-8 seconds: Starts a 60-second function test manually. The test can be aborted by pressing the OFF button (1-2 seconds).
• Press for >10 seconds: Resets the timing functions.

Indicator Status Descriptions:

• Green (Permanent on): Indicates normal status when mains power is connected.
• Green (Slow flash, 1s on/1s off): Indicates the duration test is running.
• Green (Fast flash, 0.2s on/0.2s off): Indicates the function test is running.
• Green (Normal flash three times only): Indicates a time reset has occurred.
• Red (Permanent on): Indicates battery failure during normal operation or function test.
• Red (Slow flash, 1s on/1s off): Indicates lamp failure during function test and duration test.
• Red (Fast flash, 0.2s on/0.2s off): Indicates battery incapacity during the duration test.
• Both Off: Indicates the unit is in emergency mode.

Important Note: In non-maintained mode, a lamp failure typically shows a green indicator. This indicator will turn red during a weekly functional test. Any failure indication status should be checked and rectified as soon as possible.

Initial Test Procedure: When the fitting is first powered on, press the manual test button to perform an initial test. With mains power connected, the green indicator should remain permanently on, confirming battery and LED module connections.

Charging and Testing Requirements: For accurate testing, luminaires must be connected to the mains supply for at least 24 uninterrupted hours. If mains power is switched off during a test, the test will be postponed for 3 days and will automatically initiate after 24 hours of charging.

Timing Accuracy: The timing functions have an accuracy of ±75 seconds per week and will be retained through power supply failures or interruptions for up to 7 days.

Manufacturer Information

UK Manufacturer: Kingfisher International Products Limited, 1 Paddington Square, London, W2 1GG, United Kingdom

EU Manufacturer: Kingfisher International Products B.V., Rapenburgerstraat 175E, 1011 VM Amsterdam, The Netherlands

For product information and manuals, visit:

• www.diy.com
• www.screwfix.com
• www.screwfix.ie
• www.kingfisher.com/products (for online manuals)

Made in China.