Barnes 4SE-HL Series Submersible Solids Handling Pump
15 HP
Product Overview
The Barnes 4SE-HL Series is a submersible solids handling pump designed for efficient and reliable operation. This document provides detailed specifications, performance curves, and model information for the 15 HP models.
The pump features 3" spherical solids handling capability.
Specifications
- DISCHARGE: 4" 125lb., horizontal flange
- SPEED: 1750 RPM (Nominal)
- IMPELLER:
- Design: 2 Vane, open with pump out vanes on back side, dynamically balanced, ISO G6.3
- Material: Cast iron ASTM A-48, class 30
- CORD ENTRY: 40 ft. (12.1 m) Cord. Epoxy sealed housing with secondary pressure grommet for sealing and strain relief
- MOTOR:
- Design: NEMA L- single phase, NEMA B - three phase torque curve, oil filled, squirrel cage induction
- Winding: Class F, class H rated magnet wire
- Service Factor: 1.15
- SEAL:
- Design: Dual mechanical
- Material: Carbon/Ceramic/Buna-N Hardware - 300 series stainless
- DIAPHRAGM: Buna-N
- LIFTING BAIL: 304 Stainless steel
- LIQUID TEMPERATURE: 104°F (40°C) Continuous
- VOLUTE: Cast iron ASTM A-48, class 30
- MOTOR HOUSING: Cast iron ASTM A-48, class 30
- SEAL PLATE: Cast iron ASTM A-48, class 30
- SHAFT: 416 Stainless steel
- SQUARE RINGS: Buna-N
- HARDWARE: 300 Series stainless steel
- PAINT: Air dry enamel (epoxy optional)
- BEARINGS:
- Upper Bearing: Single row, ball, oil lubricated (Radial Load)
- Lower Bearing: Single row, ball, oil lubricated (Radial Load)
- SINGLE PHASE: Capacitor start/capacitor run. Requires Barnes starter/panel which includes capacitors and overload protection.
- THREE PHASE: Tri Voltage motor 200-230/460. Requires overload protection to be included in control panel, VFD suitable.
- MOISTURE SENSOR: Normally open (N/O), requires relay in control panel.
- TEMPERATURE SENSOR: Normally Closed (N/C), Requires relay in control panel. For three phase units ONLY.
Performance Curves
The following chart illustrates the performance curves of the Barnes 4SE-HL Series pumps, showing Head (ft) versus US gpm for various impeller diameters.
Impeller Diameter vs. Pump HP:
| Pump HP | Impeller Dia mm (in.) |
|---|---|
| 7.5 | 178 (7.00) |
| 11.3 | 203 (8.00) |
| 15.0 | 229 (9.00) |
A graph showing pump performance curves with Head in feet on the Y-axis and US gpm on the X-axis. Multiple curves are plotted, representing different impeller diameters and corresponding horsepower ratings.
Model Information
| MODEL NO. | 4SE15034HL | 4SE15044HL | 4SE15054HL |
|---|---|---|---|
| PART NO. | 084646 | 084647 | 089317 |
| HP | 15 | 15 | 15 |
| VOLT/PH | 230/3 | 460/3 | 575/3 |
| Hz | 60 | 60 | 60 |
| RPM (nom) | 1750 | 1750 | 1750 |
| NEMA START CODE | D | D | D |
| FULL LOAD AMPS | 38 | 19 | 15.2 |
| LOCKED ROTOR AMPS | 160 | 80 | 64 |
| CORD SIZE | 6/4 | 6/4 | 8/4 |
| CORD TYPE | SOW | SOW | SOW |
| CORD O.D INCH (mm) | 1.06 (27) | 1.06 (27) | 0.830 (21) |
Drawings
A technical drawing illustrating the dimensions of the Barnes 4SE-HL Series submersible pump. The drawing shows the overall height, flange dimensions, and cord entry details.