Tyger Auto: Contact Us
Instruction Manual for TYGER models including: TG-LX3D82358 LanderX Running Board, TG-LX3D82358, LanderX Running Board, Running Board
Tyger Auto LanderX Running Board Compatible with 2019-2024 Ram 1500 (NOT FIT 2019-2024 Classic) | Crew Cab | TG-LX3D82358 | Drop Step Side Step Rail Nerf Bars : Automotive
File Info : application/pdf, 3 Pages, 1.62MB
DocumentDocumentTYGER LanderX TG-LX3D82358 BEFORE INSTALLATION READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. FAILURE TO IDENTIFY DAMAGE BEFORE INSTALLATION COULD LEAD TO A REJECTION OF ANY CLAIM. IF MISSING PARTS OR ANY DAMAGE FOUND, PLEASE TAKE A PICTURE FOR THE CLAIM PURPOSE. TO FILE YOUR CLAIM, PLEASE VISIT: WWW.TYGERAUTO.COM/CONTACT TORQUE VALUES Fastener Size Class 8.8 Torque (ft-lbs) 6mm 6-7 8mm 15-16 10mm 31-32 12mm 54-55 14mm 87-88 Class 10.9 Torque (ft-lbs) 6-7 22-23 44-45 78-79 125-126 x1 Driver/Left TYGER LanderX x2 Center Mounting Brackets x20 8mm x 24mm OD x 2mm Flat Washers x1 Passenger/Right TYGER LanderX x2 Center Support Brackets x16 8mm x 16mm OD x 1.6mm Flat Washers x4 Front/Rear Upper Mounting Brackets x8 8mm x 25mm Hex Bolts x28 8mm Nylon Lock Nuts x4 Front/Rear Lower Mounting Brackets x12 8mm x 25mm Combo Bolts (2) Center Support Brackets (2) Center Mounting Brackets (4) Front/Rear Upper Mounting Brackets Driver/Left TYGER LanderX (4) Front/Rear Lower Mounting Brackets 1/3 Customer Support: www.tygerauto.com/contact V230511 TYGER LanderX PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. USE WIRE BRUSH TO CLEAN MOUNTING STUDS OF PAINT AND DEBRIS. STEP 1 Start the installation under the Driver/Left side of the vehicle. Locate the front (3) factory studs along the inner side of the body panel (Fig 1). STEP 3 Select (1) Front Lower Mounting Bracket. Attach the Lower Bracket to the short side of the Upper Bracket with (2) 8mm Hex Bolts, (4) 8mm x 16mm Flat Washers and (2) 8mm Nylon Lock Nuts (Fig 3). DO NOT tighten hardware. (2) 8mm Hex Bolts (4) 8mm x 16mm Flat Washers (2) 8mm Nylon Lock Nuts Front (Fig 1) Driver/Left Front mounting location STEP 2 Select (1) Front Upper Mounting Bracket. Attach the Mounting Bracket to the (3) factory studs with (3) 8mm x 24mm Flat Washers and (3) 8mm Nylon Lock Nuts (Fig 2). DO NOT tighten hardware. (3) 8mm x 16mm Flat Washers (3) 8mm Nylon Lock Nuts Front Front (Fig 3) Attach (1) Front Lower Mounting Bracket to the Upper Mounting Bracket STEP 4 Move to the center location (Fig 4). Select (1) Center Support Bracket. Attach the Support Bracket to the (2) lower threaded studs with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts (Fig 5). Select (1) Center Mounting Bracket and attach to the Support Bracket and upper threaded stud with (2) 8mm x 24mm Flat Washers and (2) 8mm Nylon Lock Nuts (Fig 6). DO NOT tighten hardware. (Fig 2) Attach (1) Front Upper Mounting Bracket to the threaded studs Front (Fig 4) Driver/Left Center mounting location 2/3 TYGER LanderX (2) 8mm x 24mm Flat Washers (2) 8mm Nylon Lock Nuts Front STEP 6 Select the Driver/Left TYGER LanderX. With assistance, place the TYGER LanderX onto the (3) Mounting Brackets. Attach the TYGER LanderX to the Mounting Brackets with (6) 8mm Combo Bolts (Fig 8). DO NOT tighten hardware. (Fig 5) Attach (1) Support Bracket to the lower (2) threaded studs on the mounting location (2) 8mm Combo Bolts (2) 8mm x 24mm Flat Washers (2) 8mm Nylon Lock Nuts Front Front (Fig 8) Attach the Driver/Left TYGER LanderX to the (3) Mounting Brackets (Fig 6) Attach (1) Center Mounting Bracket to the upper threaded stud and Support Bracket STEP 7 Level and adjust the TYGER LanderX as necessary, then fully tighten all hardware. STEP 5 Repeat STEPS 2-3 to attach (1) Rear Upper Mounting Bracket and (1) Rear Lower Mounting Bracket to the rear mounting location (Fig 7). DO NOT tighten hardware. STEP 8 Repeat STEPS 1-7 to attach the Passenger/Right TYGER LanderX. STEP 9 Do periodic inspections to the installation to make sure that all hardware is secure and tight. Rear (Fig 7) Driver/Left Rear mounting location 3/3