ASSEMBLY INSTRUCTION
Attention: Do not tighten the screws until all of them are in right positions.
- It's recommended to have two people for the installation; this will significantly improve your efficiency.
- Before you begin: lay out all of the parts on a non-abrasive surface to identify the number tags in the manual and count before assembly. Please use the screws correctly to avoid popping the desk panel.
- For a smooth assembly process, we suggest you keep a light tightness for all the screws during assembly. After the whole desk is assembled, firmly tighten all the screws.
Parts List
Components:
- Part 1: Large flat panel (1 PC)
- Part 2: Horizontal support bar (2 PCS)
- Part 3: Vertical leg/frame piece (1 PC)
- Part 4: Top horizontal frame piece (1 PC)
- Part 5: Horizontal frame piece (1 PC)
- Part 6: Large flat panel (desktop) (1 PC)
- Part 8: Lower horizontal crossbar (2 PCS)
- Part 9: Vertical side support (1 PC)
- Part 10: Top horizontal support (1 PC)
- Part 11: Drawer runner/slide component (2 PCS)
- Part 12: Drawer runner/slide component (2 PCS)
- Part 13: Drawer box panel (2 PCS)
- Part 14: Drawer box panel (2 PCS)
- Part 15: Drawer unit component (1 PC)
- Part 16: Drawer unit component (1 PC)
Hardware:
- A: M6 x 35mm (10 PCS)
- B: M6 x 30mm Black screws for desktop fixation (8 PCS)
- C: M6 x 10mm (4 PCS)
- D: M6 x 30mm (6 PCS)
- E: M6 x 30mm (6 PCS)
- F: M4 x 10mm (2 PCS)
- G: Not specified for use in steps.
- H: M6 x 30mm (6 PCS)
- L: M4 x 10mm (2 PCS)
Assembly Steps
Step 1
Attach two side panels (Part E) to the underside of the main desktop panel (Part 1). Use 1x Part 1 and 2x Part E.
Step 2
Attach two horizontal support bars (Part 2) to the side panels (Part E). Use 2x Part 2 and 4x Screw B.
Step 3
Attach vertical leg pieces (Part 3) to the base structure. Ensure the side with square holes faces inward. Use 1x Part 3 and 4x Screw A.
Step 4
Attach the top horizontal frame piece (Part 4) to the vertical legs. Ensure the concave side faces upward. Use 1x Part 4 and 4x Screw D.
Step 5
Attach another horizontal frame piece (Part 5) to the top structure. Use 1x Part 5 and 1x Screw D.
Step 6
Attach the main desktop panel (Part 6) to the assembled frame. Use 1x Part 6 and 4x Screw B. Maintain [80% tightness] during this step.
Step 7
Attach lower horizontal crossbars (Part 8) to the frame. Use 1x Part 8, 4x Screw C, and 2x Screw A.
Step 8
Attach the top horizontal support (Part 10) to the frame. Use 1x Part 10 and 2x Screw A.
Step 9
Attach vertical side supports (Part 9) to the frame. Use 1x Part 9 and 2x Screw A.
Step 10
Attach top panels (Part E) to the frame. Use 6x Part E.
Step 11
Instructions for adjusting drawer slides: Loosen B#, Push forward [arrow] Lock B#. Loosen C#, Push down [arrow] Lock C#.
Notice: If the desktop is uneven, please adjust as described above.
Step 12
Insert drawer runner/slide components (Parts 11 and 12) into their designated slots. The diagram shows inserting L and R components. If a metal tab is not protruding, pry it open slightly.
Step 13
Insert Parts 11 and 12 into the hole and press down. Use 3x Part 11 and 3x Part 12.
Step 14
Assemble drawer boxes. Use 2x Part 13, 2x Part 14, 2x Part L, and 2x Part H.
Step 15
Attach the assembled drawer unit to the desk frame.
Step 16
Attach drawer unit component (Part 16) to another drawer unit component (Part 15). Use 1x Part 15 and 1x Part 16.
Step 17
Attach side panels/supports (Part C) to the desk. Use 2x Part C.
Step 18
Tighten all the screws from Step 1 to Step 18.
Final Configurations
The desk can be assembled into Option A (with drawers on the right) or Option B (with drawers on the left, and a side pocket/shelf on the left).
