Instruction Manual for CROTONE models including: MAA-F005, Door Lock, MAA-F005 Door Lock
Created Date: 5/11/2021 4:49:44 PM
Cerradura Chapa Smart Inteligente Wifi APP Tuya Smart Huella Tarjeta Código - Cronte Technology
Installation manual of intelligent door lock
Left and right reversing of lock body
ffiffi
f, :;'1,31Í ;i3n:";;";il:13 u-tlh
When installing upward, and the the front panel
the lock body, the inclined tongue sha11 face
inclined surface of inclined tongue sha11 face direction. If it is not consistent, the
direction of inclined tongue sha11 be adjusted. The method is
as follows:
1. Turn the lock body upside down with the inclined tongue
downward, and 1et the int-1ined tongue stop block lean down. As shown in Figure 2 2. Press the inclined tongue to the bottom and rotate 180
degrees.
3. Loosen
the
inclined
tongue,
1et
it
pop out along the
inclined tongue ho1e, and turn the lock body upside down. As
shown in Figure 3
Square shaft installation
Insert the hole end of the big shaft into the square
hole on the hand, concentric with the two sma11 round holes, and insert the pin to
bend the pin, which is not easy to faIl off
a
B
uare shaft
§oo
{
When installing the pane1, first check whether the panel handle is consistent with the left and right door opening. If, not, adjust the handle direction. The operation is as follows: 1. Use a 3mm A11en wrench to remove the M6 hexagon screw in the side hole of the square shaft (take out the handle from the panel). 2. Rotate the handle upward bv 180 degrees, and install the screw lnto another hole to t ighten the
SCTEW.
Installation of lock body
Installation of lock body: the tlnhcelininecdlinteondguseurifsacuepiwsarfda,cianngd the front panel
&
Self tapping screw
ue tongue
cotter pin
s
Square ton
lnstallation of door buckle
plate and door buckle box
Dig holes on the door frame corresponding to the lock tongue, and
then fix them with two wood screws
Installation exploded view
Insta llation direction diagram of intelligent door lock
Right door opening direction change:
Tahligenteridantoglethesym"5b0o"l
should be rotated position when the
and
right door is opened
Note: when equipped with single tongue
lock body, the triangle symbol
installed in R direction
sha1l
be
o@
dThoeordhiraencdtlieonisoafsthfoelloriwgsht
The directlon of the right
door handle is as fo 1 lows
o@
Wisheinn sthtaellreigdhwt idthoothr eisheoxpaegnoend,scthreew hole
front panel
Note: when changing the left and right handles of
the front panel, remove the hexagon screws in the
ufrpownatrdpbayne1l8w0 itoh
aan3dmminAslt1aenll
key, rotate
the hexagon
the handle
screws
into another hole
@e
Rear panel
Note: when changing the left and right handle of the rear pane1, remove the hexagon screw in the pupawnaerldwbitvh1a803mom Aan11deinnksetay,llrothtaetehetxhaegohnanscdrleew into another hole
Left door switch d irection:
@
The direction of the left door handle is as follows
0
The and
triangle symbol aligned to the
t"5s-^0rh, o" upldosbietiornotaotfed
the left door
Note: when equipped with single
tongue lock body, the triangle symbol
sha11 be installed in L direction
The direction of the left door handle is as follows
When the left door , the inner hexagon screw is used to install the hole
@o
Rear panel
Note: when changing the left and right handle of
the rear panel, remove the hexagon screw in the
uppawnaerldwbitvh1a803mom
Allen key, and install
rotáte the handle the hexagon screw
into another hole
front panel
\-' When the right door , the hole is
installed with the hexa SCTCW
Note: when changing the left and right handles of
the front pane1, remove the hexagon screws in the
furpownatrdpbayne1l8w0 itoh
a 3mm Al1en and install
.key, rotate the hexagon
the handle s crews into
another hole
Canon SC1011 IJ Scan Utility