Revive Adjustable Bed Base Owner's Manual
Installation & Operation
Serial No.: [Serial Number Placeholder]
Safety & Warranty Warnings
Read the following information carefully before using this product. If unable to understand warnings, cautions, and/or instructions, contact the dealer or technical personnel if applicable, before attempting to use the equipment. Otherwise, injury or damage may result.
Safety Warnings:
- Do not use the bed outdoors.
- Do not use the bed near explosives.
- Using the bed with oxygen administering equipment other than the nasal masked type creates a possible fire hazard.
- When using nasal or masked type administering equipment, route and secure oxygen or air tubing properly to ensure that tubing does not become entangled or damaged during normal operation of the bed.
- Use caution when having liquids in or around the bed to ensure no spilling occurs. In case of spillage, stand in a dry, clean area of the floor and unplug the bed immediately. Clean up spill and allow the area around the bed to dry thoroughly before using the electric controls again. Do not eat or drink hot liquids while operating the bed.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the appliance by a person responsible for their safety.
- Do not allow children or individuals with disabilities to operate the bed without adult supervision.
- Do not allow any person or pet under the bed at any time.
- During bed operation, make sure the body is positioned within the confines of the bed. Do not place extremities over the sides of the bed when operating bed functions.
Warranty Warnings:
- Do not open or tamper with the control box, motors, or remote (with the exception of battery compartments). The warranty will be void if the internal workings of these components are tampered with.
Product Rating:
The motors are not designed to operate continuously for more than [2] minutes in an [18] minute time period or approximately 10% duty cycle. Attempting to circumvent or exceed this rating will shorten the life expectancy of the foundation and may void the warranty.
Operating Information:
- After power foundation assembly is completed, operate the remote control to ensure proper functions.
- Keep moving parts free of obstruction during bed operation (including sheets, clothing, tubing, wiring, and products using electric power cords).
- Distribute body weight evenly over the bed surface. Do not place entire weight on head or foot sections of the bed, during repositioning and entering or exiting the bed.
Hospital Use Disclaimer:
This power foundation is designed for residential use only. It is not approved for hospital use and does not comply with hospital standards.
Weight Limits:
This product is not rated to support weights in excess of 850 pounds inclusive of the mattress and bedding. The bed will structurally support this weight, provided it is evenly distributed across the foundation. The power foundation is not designed to support or lift this amount in the head or foot sections alone. Exceeding this weight restriction could damage the bed and/or cause injury and will void the warranty.
WARNING: DO NOT USE THIS BED IF WEIGHT LIMITATION IS EXCEEDED.
Radio Frequency:
2.4 GHz
FCC Compliance:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To comply with the FCC RF exposure requirements, no change to the antenna or the device is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirement and void the user's right to operate the device.
Customer Service: 1-855-430-8943
Parts List
All electronics and components that need to be installed are located in boxes under the foundation or attached to the frame. Before discarding the packing materials, ensure that all the parts are accounted for.
Components:
- (4) 9" adjustable legs
- (1) Hand Control
- (2) T Brackets
- (2) Headboard Brackets
- (1) Power Supply
- (12) Nuts
- (8) Long Bolts
- (1) Power Cord
- (4) Short Bolts
- Accessories Box containing (2) AAA Batteries
- Headboard Bracket Box (Optional)
Optional Equipment (Not Included):
- (2) 9-Volt Batteries
- Socket and Crescent Wrench
Actual product appearance and functionality may vary from photographs.
Customer Service: 1-855-430-8943
LS1000 Electronics Quick Reference Guide
LS1000 Wireless Overview
Base Components: The base includes a Control Box and a Head Motor.
System Diagram: The system consists of a Remote, Control Box, Head Motor, Power Supply, Power Cord, and a Pairing Button.
LS2000 Electronics Quick Reference Guide
LS2000 Wireless Overview
Base Components: The base includes a Head Motor, a Control Box, and a Foot Motor.
System Diagram: The system consists of a Remote, Control Box, Head Motor, Foot Motor, Power Supply, Power Cord, and a Pairing Button.
LS3000 Electronics Quick Reference Guide
LS3000 Wireless Overview
Base Components: The base includes a Control Box, Foot Motor, LED Light, Head Motor, Head Massage Motor, Foot Massage Motor, and USB Ports.
System Diagram: The system consists of a Remote, Control Box, Foot Motor, Head Motor, Head Massage Motor, Foot Massage Motor, USB Ports, LED Light, Power Supply, Power Cord, and a Pairing Button.
LS6000 Electronics Quick Reference Guide
LS6000 Wireless Overview
Base Components: The base includes a Lumbar Motor, LED Light, Headrest Motor, Head Massage Motor, Foot Motor, USB Ports, Bluetooth, Head Motor, Control Box, and Foot Massage Motor.
System Diagram: The system consists of a Remote, Bluetooth module, Control Box, Foot Motor, Head Motor, Headrest Motor, Lumbar Motor, Head Massage Motor, Foot Massage Motor, USB Ports, LED Light, Power Supply, Power Cord, and a Pairing Button.
Installation Guide
Two people are required to set up the foundation.
Note: To avoid damage to the foundation, always open the carton while the bed is in the flat position.
- Step 1: Place the foundation box in a desired location with the bottom of the box facing up. Remove the binding straps and packing materials, making sure not to puncture the box with any sharp objects.
- Step 2: Remove the foundation from the box, keeping the bottom of the foundation facing upward for easier access to the bed's components.
- Step 3: To install the legs, thread the bolt of the leg to the nut on the foundation frame, and tighten by hand. DO NOT OVERTIGHTEN.
- Step 4: Uncoil the input power cord (connected to the control box's power port) and plug it into the power supply.
- Step 5: Uncoil the power cord and connect it to the power supply.
- Step 6: Locate the power supply and install (2) 9-volt batteries (not included).
- Step 7: Carefully flip the foundation over onto its legs. Important: Two people are required to move the foundation. Do not drag across the floor. Do not rest frame on its side; excessive pressure may damage the legs.
- Step 8: Ensure that batteries are correctly installed.
- Step 9: Locate the mattress retainer bar brackets. Slide the left side of the mattress retainer bar into the bracket. Pull the retainer bar to the opposite bracket and secure the right side.
Customer Service: 1-855-430-8943
LS1000/LS2000 Remote Control Instructions
LS1000 Remote:
Adjustments:
- HEAD [up arrow] / [down arrow]: Lifts and lowers the head section of the foundation.
- [Flash symbol]: One touch flash light on/off.
One Touch Buttons:
- FLAT: One touch FLAT preset position.
- M: One touch memorized position.
LS2000 Remote:
Adjustments:
- HEAD [up arrow] / [down arrow]: Lifts and lowers the head section of the foundation.
- FOOT [up arrow] / [down arrow]: Lifts and lowers the foot section of the foundation.
One Touch Buttons:
- FLAT: One touch FLAT preset position.
- M: One touch memorized position.
Customer Service: 1-855-430-8943
LS3000 Remote Control Instructions
LS3000 Remote:
Adjustments:
- HEAD [up arrow] / [down arrow]: Lifts and lowers the head section of the base.
- FOOT [up arrow] / [down arrow]: Lifts and lowers the foot section of the base.
- [double up arrow] / [double down arrow]: Lifts and lowers the head & foot section of the base.
One Touch Buttons:
- TV: One touch TV preset position.
- ZG: One touch Zero-G preset position.
- FLAT: One touch FLAT preset position.
- M1, M2: One touch programmable preset position.
- [Light symbol]: One touch under bed LED light on/off.
Massage Feature:
- [Head Massage button]: Turns on head massage, cycles through 3 intensities.
- [Foot Massage button]: Turns on foot massage, cycles through 3 intensities.
- [MODE button]: Changes massage modes, cycles through 5 intensities.
- ALL OFF: Turns off massage.
Customer Service: 1-855-430-8943
LS6000 Remote Control Instructions
LS6000 Remote:
Adjustments:
- HEAD [up arrow] / [down arrow]: Lifts and lowers the head section of the base.
- FOOT [up arrow] / [down arrow]: Lifts and lowers the foot section of the base.
- Headrest [up arrow] / [down arrow]: Lifts and lowers the Headrest section of the base.
- Lumbar [up arrow] / [down arrow]: Lifts and lowers Lumbar.
One Touch Buttons:
- TV: One touch TV preset position.
- ZG: One touch Zero-G preset position.
- FLAT: One touch FLAT preset position.
- M1, M2: One touch programmable preset position.
- [Light symbol]: One touch under bed LED light on/off.
Massage Feature:
- [Head Massage button]: Turns on head massage, cycles through 3 intensities.
- [Foot Massage button]: Turns on foot massage, cycles through 3 intensities.
- [MODE button]: Changes massage modes, cycles through 5 intensities.
- ALL OFF: Turns off massage.
Customer Service: 1-855-430-8943
Setting Programmable Positions and Pairing Remote
Setting Programmable Positions:
The wireless power bed has a programmable feature that allows you to save custom positions. Please read all the instructions below before setting your custom presets on the remote.
- Step 1: Adjust the head and foot to your desired position.
- Step 2: Press and hold the FLAT button first, then press and hold the M button for 5 seconds until the buttons' lights are flashing. The position is then saved.
- Step 3: To adjust the saved position, repeat steps 1 and 2, and the new position will be saved.
Pairing Remote:
The original remote that comes in the box is already paired to the foundation. No further action is required. In the event that the remote is not paired with the foundation, follow the steps below.
- Step 1: Make sure the batteries work fine. Replace them when needed.
- Step 2: Plug the power cord to the power source.
- Step 3:
- For LS1000: Press and hold HEAD [up arrow] and FOOT [down arrow] simultaneously, then press and hold the pairing button on the control box cord for 3 seconds until you hear 2 beeps sound; the remote is then paired.
- For LS2000/LS3000/LS6000: Press and hold HEAD [up arrow] and FOOT [down arrow] simultaneously, then press and hold the pairing button on the control box cord for 3 seconds until you hear 2 beeps sound; the remote is then paired.
Customer Service: 1-855-430-8943
Synchronizing Two Bases
Synchronizing Two Bases:
If simultaneous operation of two foundations is desired, please read pairing remotes instructions on page 11.
- Step 1: Plug A and B bases to power source.
- Step 2: Make sure remote A was already paired to Base A and Remote B was paired to Base B. If not, please pair them by following the pairing remote instructions on page 11.
- Step 3: Pair remote A to Base B, then base A and base B can be simultaneously operated by Remote A.
- Step 4: Set Remote B to operate both bases too.
- For LS1000 (one motor bed)/LS2000, only one remote can control both bases.
- Note: If you want to operate the beds separately, only need to use another remote to be paired to one of the beds.
- For LS3000/LS6000, please follow the instructions below. Press and hold HEAD [down arrow] and FOOT [down arrow] buttons on remote B. The back light of the button will flash. Meanwhile, press and hold HEAD [up arrow] and FOOT [up arrow] buttons on Remote A. The learning process is successful when the back light of the button on remote B starts to flash. Now both remotes will be able to operate both beds simultaneously.
- Note: If you want to operate the beds separately, for LS3000, press and hold HEAD [up arrow] and FOOT [down arrow] on remote B. For LS6000, press and hold HEAD [up arrow] and FOOT [down arrow] on remote B, then the back light of the button will flash, and the remote B has been separated from the remote A.
Customer Service: 1-855-430-8943
Headboard Bracket Installation Guide
Headboard brackets are an optional accessory and are not included. A 1/2" (13 mm) socket and 1/2" (13 mm) crescent wrench are necessary to complete installation.
Headboard Bracket Components:
- (2) Headboard Brackets
- (2) T-Brackets
- (4) Short Bolts
- (12) Nuts
- (8) Long Bolts
- Step 1: The headboard bracket will have 2 long slots to accommodate any frame type. Align the appropriate slots on the bracket with the holes on the bed. Use long bolts and nuts to secure the bracket. Make sure the bolts are tight.
- Step 2: To put the T-Bracket and Headboard Bracket together, you will need (2) short bolts and (2) nuts. Slip the bolts through the holes from T-Bracket to Headboard Bracket with the head of the bolt facing outward. Use a 1/2" (13mm) socket and 1/2" (13mm) wrench to tighten the bolts.
- Step 3: You may now connect your headboard to the attachment plates using the remaining short bolts and nuts to secure it to the brackets. The heads of the bolts will face outward. Use a 1/2" (13 mm) socket and 1/2" (13 mm) wrench to tighten the bolts.
Customer Service: 1-855-430-8943
Troubleshooting
In the event that the power foundation fails to operate, assess the symptoms and possible solutions provided in the chart below.
| Symptoms | Solutions |
|---|---|
| Remote control illuminates and appears to be operable, but will not activate bed. | Verify that the power cord is plugged into a working, grounded electrical outlet. Test the outlet by plugging in another working appliance. |
| No features of the power foundation will activate. | Program the remote control (see the Setting Programmable Positions and Pairing Remote section of this manual for programming procedures). Unplug the power cord, wait 30 seconds and plug back to reset electronic components. The surge protection device or the electrical outlet may be defective. Test the outlet by plugging in another working appliance. Verify that the connector on the wired remote control is securely attached to the control box. |
| Wireless remote will not illuminate. | Replace the batteries in the wireless remote. |
| Head or foot section will elevate, but will not return to the horizontal (flat) position. | Bed mechanism may be obstructed. Elevate bed and check for obstruction. Remove obstruction. Head section may be too close to the wall. Headboard may be too close to the edge of the mattress. Verify that there is enough distance between the headboard brackets and mattress. Adjust if required. |
| Head & Foot lift function has minor interference during operation. | Check batteries in wireless remote control, replace with two (2) new AAA batteries if necessary. Make sure that you are following the duty cycle of the motors (do not operate more than two minutes over a 20-minute period, or approximately 10% duty cycle). Press the lift buttons squarely and accurately. Wireless remote control may be experiencing common Radio Frequency Interference from other radio transmitting devices. Wait several seconds, and then try pressing the appropriate button again. See FCC Compliance Statement on page 1 of this guide. |
| Excessive massage motor noise. | If the bed is located on hard surface flooring, place carpet pieces or rubber pieces (not included) under each leg. Using the wireless remote control, elevate the head, foot or neck section a short distance to realign the lift/lower mechanisms with the bed support platform. Verify that your Revive Power Foundation is not positioned against a wall, nightstand, or other object that may cause the vibration or noise. If the Revive Power Foundation is installed over a bed frame, verify that the massage motors are not causing the bed frame (or bed frame components) to vibrate. Verify that the headboard attachment hardware is properly tightened (if used). |
| A clicking noise is heard under the bed when raising or lowering. | This is normal. The lift motor relays "click" when they are engaged. No action is required. |
| Massage motor overheats or stops. | If the vibration motor overheats, the thermal protection will turn the motor off. Wait 30 minutes, turn the massage back on. If it does not come on, turn it off and report the situation to customer service. |
Customer Service: 1-855-430-8943
