Instruction Manual for OPTONICA models including: 6385 PIR Sensor Stair Light Controller, 6385, PIR Sensor Stair Light Controller
PIR Sensor Stair Light Controller | OptonicaLED
Output type Constant voltage SPI(TTL) Output power 32 x (5-24)W Output voltage 32 x (5-24)VDC Output current 32CH,1A/CH Input voltage 5-24VDC TechnicalParameters
< < < + + + + SPI OUTPUT SPI OUTPUT PIR Sensor Stair Light Controller SKU: 6385 PIR sensor/Daylight Sensor/Max 32 step/Compatible with 27 kinds IC/Max 960 pixels/OLED display Features Multiple function PIR sensor stair light controller with daylight sensor. 32 channels constant voltage output drive low voltage LED strip, Max. 1A current per channel. 2 groups SPI(TTL) signal output, drive 27 kinds IC digital RGB LED strip, IC type and R/G/B order can be set. Compatible ICs: TM1803, TM1804, TM1809, TM1812, UCS1903, UCS1909, UCS1912, UCS2903, UCS2909, UCS2912, WS2811,WS2812, TM1829, TM1914A, GW6205, GS8206,GS8208,LPD6803, LPD1101, D705, UCS6909, UCS6912, LPD8803, LPD8806, WS2801, WS2803, P9813, SK9822. Easy operation with OLED display and 3 buttons. four work light mode selectable. Two stair light controller can cascade. Built-in multiple color mode, speed and brightness 1-8 grade adjustable. Push switch can also be as induction signal input. With fast self-testing function. LVD Any damaged LED channel in 32 channels can be set disable. Technical Parameters Input and Output Input voltage Output voltage Output current Output power Output type 5-24VDC 32 x (5-24)VDC 32CH,1A/CH 32 x (5-24)W Constant voltage + SPI(TTL) Safety and EMC EMC standard (EMC) Safety standard(LVD) Certification ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 62368-1:2020+A11:2020 CE,EMC,LVD Environment Operation temperature Ta: -30O C ~ +55 O C Case temperature (Max.) T c:+85O C IP rating IP20 Sensor data Sensitive field Sensitivity angle 3m 120 Warranty and Protection Warranty Protection 3 years Reverse polarity Mechanical Structures and Installations Up PIR sensor input 2 groups SPI signal output 01-16 step constant voltage LED output UP PIR INPUT 01 02 03 04 05 06 07 08 09 10 11 12 01-16 STEP LED OUTPUT LUX DET 13 14 15 16 INPUT INPUT 5-24VDC CLK DA GND DA CLK PIR Sensor Stair Light Controller Uin=5-24VDC Uout=5-24VDC I o u t = 3 2 C H×1 A Temp Range: -30-+55 M< CASCADE GND UP DW 17 18 19 20 17-32 STEP LED OUTPUT 21 22 23 24 25 26 27 28 29 30 31 32 DW PIR INPUT Cascade input/output or Push switch input 17-32 step constant voltage LED output Daylight sensor input OLED Digital display Power Input + Power Input Setting key Down PIR sensor input 86.00 mm 68.00 mm 186.00 mm Accessories 25.50 mm 186.00 mm LED Controller 1 pcs Wiring Diagram Up direction PIR sensor + + UserManual 1pcs Daylight sensor 30cm 1 pcs PIR sensor 2 pcs 16 x Single color LED strip + + Daylight sensor PIR sensor extension line5m 2 pcs UP PIR INPUT 01 02 03 04 05 06 07 08 09 10 11 12 01-16 STEP LED OUTPUT LUX DET 13 14 15 16 INPUT 5-24VDC INPUT CLK DA GND DA CLK PIR Sensor Stair Light Controller Uin=5-24VDC Uout=5-24VDC I o u t = 3 2 C H×1 A Temp Range: -30-+55 M< CASCADE GND UP DW 17 18 19 20 17-32 STEP LED OUTPUT 21 22 23 24 25 26 27 28 29 30 31 32 DW PIR INPUT Power Supply 5-24VDC Constant Voltage AC100-240V SPI signal VDA V+ 16 x Single color LED strip RGB LED pixel strip Down direction PIR sensor Note: The LED pixel strip also use separate power supply. OLED screen and key operation M< 1. Short press M key, enter current work light mode parameter setting state. 2. Long press M key for 2s, enter system parameter setting state, to switch four work light mode, set light off mode, set push switch input function, set chip type and RGB order, set daylight sensor threshold. 3. When in parameter setting state, short press M key to switch between multiple parameter item, press < or > key for parameter adjustment. 4. Long press M key or wait 15s to quit parameter setting state. 5. Long press M & > key for 2s, start up direction induction light testing. 6. Long press M & < key for 2s, start down direction induction light testing. 7. Long press < & > key for 2s, restore factory default parameter. 8. Long press <, > & M for 2s, enter 32 channels LED disable setting interface. 9. The fourth line display color mode name defaultly, and will display induction signal input indication or light on/off state. 10. When induction light control process is over, the light will turn off after 10s(@speed 8) automatically. For speed 1-8 level, the turn off delay time is 45/40/35/30/25/20/15/10s respective System parameter setting WorkMode:CV_Step Off: Delay sync Push:Cascade LuxSet:OFF *050 WorkMode:CV+SD_L Chip:TM1809 RGB DefRGB: FF FF 80 LuxSet:OFF *050 WorkMode: Switch between four work light mode. CV_Step: Only multiple constant voltage LED strip light mode. SD_Line: Only 1 or 2 straight line digital pixel LED strip light mode. SD_Step: Only multiple Z-shape digital pixel LED strip light mode. CV+SD_L : Multiple constant voltage LED strip + 1 or 2 straight line digital pixel LED strip light mode. Off: Switch between two light turn off mode when induction light control process is over. Delay sync: The light turn off at the same time after the delay time. One by one: The light turn off one by one from the tail end. Push: Switch between two push switch function. Cascade: The push switch input work as cascade input/output or simulate PIR inductive input. Light on: The push operation will turn on all light and turn off automatically after the delay time. Chip: Switch between 10 class chip (below table) and 6 kinds RGB order (RGB,RBG,GRB,GBR,BRG,BGR). These parameter is valid only for the work mode with SPI signal output. DefRGB: RGB hex value for user-define color. The parameter is valid only for the work mode with SPI signal output. LuxSet: Daylight sensor threshold or disable (10, 30, 50, 100, 150, 200lux,OFF), With sufficient ambient light, the PIR sensor does not turn on the light. The digital value after * is current detected LUX value. Digital pixel RGB LED strip compatible IC type list: IC type TM1809 TM1829 TM1914A GW6205 GS8206 LPD6803 LPD8803 WS2801 P9813 SK9822 Compatible IC type TM1804,TM1812,UCS1903,UCS1909,UCS1912, UCS2903,UCS2909,UCS2912,WS2811,WS2812 GS8208 LPD1101,D705,UCS6909,UCS6912 LPD8806 WS2803 Output signal DATA DATA DATA DATA DATA DATA,CLK DATA,CLK DATA,CLK DATA,CLK DATA,CLK Page 1 + + + + Constant voltage LED strip light mode CV_Step Step:032 Bri:8 Mode:01 Speed:6 ON one by one Step: Total step number, 008-032 Mode: White mode number, 01-03 Bri: Brightness grade, 1-8, 8 is the brightest level. Speed: Speed grade, 1-8, 8 is the fastest speed. + 16 + 15 + 14 + 03 + 02 + 01 White mode list: No. Name 01 ON one by one 02 All OFF,Five ON 03 All ON,one OFF LED channel output disable setup: LED disable 1110111111111111 1111111111111111 ch:04 1:on 0:off For example: If the fourth channel output is damaged, please long press M ,< & > key to enter LED disable interface, then change the corresponding channel(04) from 1(on) to 0(off). namely the damaged channel can be ignored. Straight line digital pixel LED strip light mode SD_Line Dot: 300 Bri:8 Mode:09 Speed:6 Color queue Dot: Pixel dot number, 032-960 Mode: Color mode number, 01-12 Bri: Brightness grade, 1-8, 8 is the brightest level. Speed: Speed grade, 1-8, 8 is the fastest speed. Color mode list: No. Name 01 Red 02 Orange 03 Yellow 04 Green 05 Cyan 06 Blue 07 Purple 08 White 09 Color queue ( 7 color + White) 10 Color chase( 7 color + White) 11 Color fade (6 color flow) 12 Rxxx Gxxx Bxxx (User define) S-shape digital pixel LED strip light mode SD_Step Step:030 Dot:010 Mode:09 Speed:6 Color queue Step: Total step number, 008-160 Dot: Pixel dot number of each step, 002-120 The Step number x Dot number must < 960 Mode: Color mode number, 01-12 Speed: Speed grade, 1-8, 8 is the fastest speed ++ 16 ++ 15 ++ 14 ++ 03 ++ 02 ++ 01 Color mode list: No. Name 01 Red 02 Orange 03 Yellow 04 Green 05 Cyan 06 Blue 07 Purple 08 White 09 Color queue ( 7 color + White) 10 Color chase ( 7 color + White) 11 Color fade (6 color fade) 12 Rxxx Gxxx Bxxx (User define) Constant voltage LED strip + Straight line digital pixel LED strip light mode CV_Step+SD_Line Step:032 Dot:300 Mode:09 Speed:6 Color queue Step: Total step number, 008-032 Dot: Pixel dot number, 032-960 Mode: Color mode number, 01-12 The mode number is used for straight line digital pixel LED strip only. The mode for constant voltage LED strip is fixed On one by one. Speed: Speed grade, 1-8, 8 is the fastest speed. Color mode list: + 16 + 15 + 14 + 03 + 02 + 01 No. Name 01 Red 02 Orange 03 Yellow 04 Green 05 Cyan 06 Blue 07 Purple 08 White 09 Color queue ( 7 color + White) 10 Color chase ( 7 color + White) 11 Color fade (6 color flow) 12 Rxxx Gxxx Bxxx (User define) Two stair light controller cascade connection The under stair light controller connect Up direction PIR sensor and daylight sensor. The up stair light controller connect Down direction PIR sensor and daylight sensor. Two stair light controller connect cascade UP/DW line. The push switch function must be set as cascade input. Daylight sensor Up stair light controller Up direction PIR sensor Down direction PIR sensor Daylight sensor Under stair light controller Two Push switch as up/down induction signal input connection The under push switch connect cascade UP port of the stair light controller. The up push switch connect cascade DW port of the stair light controller. The push switch operation will ignore daylight sensor threshold setting. When the push switch function be set as cascade input/output, the push operation will start induction light control process. When the push switch function be set as light on input, the push operation will turn on all light, and the light will turn off after 20s(@speed 8) automatically. For speed 1-8 level, the turn off delay time is 90/80/70/60/50/40/30/20s respectively. Up push switch Under push switch IMPORTER: Prima Group 2004 LTD, Bulgaria, 1784 Sofia, Mladost 1, bl. 144, Ground Floor; Phone: +359 2 988 45 72; Page 2Corel PDF Engine Version 16.1.0.843