Powersports Vehicle Parts | Performance Ignition & Fuel Parts | Dynojet
Installation Guide for Dynojet models including: Power Commander 6 Triumph Speed Triple 1200 RS 2021, Triumph Speed Triple 1200 RS 2021, Power Commander 6, Triple 1200 RS 2021, Triple 1200
Dynojet Power Commander 6 Triumph Speed Triple 1200 RS 2021 - Cycle Gear
Dynojet Power Commander 6 Triumph Speed Triple 1200 RS 2021 - RevZilla
File Info : application/pdf, 6 Pages, 2.77MB
DocumentDocumentPOWER COMMANDER 6 Install guide for PC6-21033 Model coverage: 2021-2022 Triumph Speed Triple 1200 PARTS LIST 1 POWER COMMANDER 6 1 INSTALLATION GUIDE 1 USB CABLE 2 DYNOJET DECALS 2 POWER COMMANDER DECALS 2 VELCRO STRIPS 1 ALCOHOL SWAB PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION. IPC6-21033.01 INPUT ACCESSORY GUIDE USB CONNECTION EXPANSION PORTS 1 & 2 OPTIONAL ACCESSORY INPUTS INPUT 1 INPUT 1 INPUT 2 INPUT 2 SPEED ANALOG CRANK Map (Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You can switch on the fly between these two base maps when you hook up a switch to the MAP inputs. You can use any open/close type switch. The polarity of the wires is not important. Shifter (Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the wires from the Dynojet quick shifter into either Input 1 or Input 2. The polarity of the wires is not important. Set to Input 2 by default. Speed If your application has a speed sensor then you can tap into the signal side of the sensor and run a wire into this input. This will allow you to calculate gear position in the Control Center Software. Once gear position is setup you can alter your map based on gear position and setup gear dependent kill times when using a quickshifter. . Analog This input is for a 0-5v signal such as engine temp, boost, etc. Once this input is established you can alter your fuel curve based on this input in the Power Core software. Launch You can connect a wire to either Input 1 or Input 2 and then the other end to a switch. This switch when engaged (continuity) will only allow the RPM to be raised to a certain limit (set in the software). When released, you will have full RPM. WIRE CONNECTIONS To input wires into the PC6 first remove the rubber plug on the backside of the unit and loosen the screw for the corresponding input. Using a 22-24 gauge wire, strip about 10mm from its end. Push the wire into the hole of the PC6 until iT stops and then tighten the screw. Make sure to reinstall the rubber plug. NOTE: If you tin the wires with solder it will make inserting them easier. 2 21-22 TRIUMPH SPEED TRIPLE 1200 PC6-21033 INSTALLING THE POWER COMMANDER 6 1 Remove the seat and fuel tank. 2 Lay the PC6 in the tail section and route the harness down the right side of the motorcycle going towards the throttle bodies. 3 Attach the ground wire of the PC6 to the negative (-) side of the battery. 4 Remove the bolt that holds the MAP sensor in place. 5 Remove the bolt on the right side of the frame that holds the ECU in place and move the ECU out of the way. This allows access to the fuel injectors. 3 6 Unplug the stock wiring harness from each injector. 7 Plug the PC6 in-line of the stock wiring harness and each injector. PC6 harness: GREEN wires - cylinder #1 (left) YELLOW wires - cylinder #2 ORANGE wires - cylinder #3 (right) Note: If you were to do individual cylinder mapping this would be opposite the software tables. 8 Unplug the Crank Position Sensor connector. This is a BLACK, 2 pin connector on top of the engine case, underneath where the ECU is located. 9 Plug the PC6 wiring harness in-line of the Crank Position Sensor and the stock wiring harness. 4 21-22 TRIUMPH SPEED TRIPLE 1200 PC6-21033 10 Unplug the Throttle Position Sensor connector. This is a BLACK 6 pin connector located on the left side of the throttle body. 11 Plug the PC6 in-line of the stock TPS and wiring harness. 12 Reinstall thefuel tank and bodywork. Download the latest map files from our web site at dynojet.com/tunes. 5 2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 - 800-992-4993 - DYNOJET.COM © 2015-2020 DYNOJET RESEARCH ALL RIGHTS RESERVED