Sunstone 30" Appliance Cabinet Setup Instructions

Model: SAC30APC

Product Overview & Dimensions

The Sunstone 30" Appliance Cabinet is designed to house appliances up to 21" wide, such as refrigerators, wine coolers, and ice makers. It is constructed from 304 stainless steel for durability and longevity.

Product Dimensions:

Width: 30"
Depth (with panel): 28-1/4"
Height (with legs): 34-1/2"
Height (without legs): 30-1/2"
Maximum height with Peg-Leg extension: Up to 36"

Diagram shows a 3D view of the cabinet with dimensions labeled for width, depth, and height, including details like the electrical box, removable counter rail, and peg-legs.

Product Inserts Dimensions:

Width: 21"
Depth: 18-3/4"
Height: 33-1/4"
Front Panel Depth: 25-1/4"

Diagram illustrates the interior space for appliance insertion, highlighting the width, depth, and height, and notes that removing the counter rail adds 1" of height.

Configuration Options:

The cabinet offers flexibility in appliance fit. Option 1 accommodates a standard 21" width by 34" height insert. Option 2 allows for increased height by removing the top counter rail and support, and adjusting the peg-legs up to 1-1/2".

Included Components:

Front Kick Plates
Back Solid Kick Plate
(4) Adjustable Peg Legs
Front Electrical Cover
Back Panel Electrical Box

Material Specifications:

Structure: 304 Stainless Steel
Door Panel: 18 Gauge
Cabinet Box: 18 Gauge
Shelf: 18 Gauge
Handles: Solid 304 Stainless Steel Bar

Assembly Instructions

Step A: Connecting Side Panels

Align the individual pins of the back panel (SCC21SPE) with the adjacent notches on the side panels (SCC4SPEL on left, SCC4SPER on right). Ensure the back panel is elevated and securely attached.

IMPORTANT! Ensure all front-facing electrical components are wired before attaching cabinets, as access will be limited later.

Secure the panels using the provided screws. There are four pre-drilled holes on each side panel. Two screws are at the top, one in the middle, and one at the bottom. The holes on the SCC4SPEL and SCC4SPER panels are threaded.

Step C: Height Adjustment & Support Beam

For appliances taller than 34-1/2", you can increase the height by extending the Peg-Legs up to an additional 1-1/2" or by not installing the support arm, which provides an immediate 1" height clearance.

The back panel (SCC21SPE) includes a cross-beam support with a counter rail. Mount this panel to the left and right sides using the included screws to support the counter front.

IMPORTANT! If removing counter rails for a Full Bullnose or Waterfall counter edge, remove all counter rails BEFORE connecting cabinets and BEFORE installing the counter.

Diagram shows an example of a waterfall edge.

Step E: Creating Multiple Appliance Runs

To create multi-appliance runs, connect additional back panels. Use Item No. SCC25SPE for fridges up to 25" width, SCC21SPE for fridges up to 21" width, and SCC15SPE for fridges up to 15" width. Use bolts and lock-nuts when connecting panels.

Step F: Front Support Arms

Attach multiple front support arms to the underside of the counter. Pre-drilled holes in each corner panel allow the counter installer to bolt from the underside, securing the support arms to the cabinet front trim panels.

IMPORTANT! When extending the counter across open areas without support, consult your counter installer about installing a special steel rod recessed into the underside of the counter.

Step G: Electrical Installation

Install all electrical boxes and peg legs before proceeding. Electrical wires are installed after cabinets are connected but before the counter is installed.

Use a GFCI 2-way electrical outlet in the front-facing panel. Standard electrical outlets can be placed on the interior. The cover panel can be removed and hung below when electrical is in use.

Punch out the black plastic utility cover port to route electrical wires, gas lines, or water lines through consecutive cabinets.

Step H: Kick-Plate Installation

IMPORTANT! Always install Kick-Plates after all cabinets are completely assembled and leveled. Refer to the main cabinet instruction manual for leveling Peg-Legs. Install Kick-Plates from Left to Right.

Place Kick-Plates by sliding open slots onto the provided small pegs, then sliding to the left. They can be easily removed for access to the underside of the cabinet. End kickplates are installed last.

	Sunstone 6" Jacket Divider Box Panel Installation Guide Instructions and specifications for installing the Sunstone 6" Jacket Divider Box Panel (Item No. SUNJKDIV6) to create jacket combinations within a single cut-out.
	Sunstone Orion x-Series Users Guide: Setup, Operation, and Features This user guide provides comprehensive instructions for setting up, operating, and maintaining the Sunstone Orion x-Series pulse arc welder, detailing its features, components, and welding procedures.
	Sunstone Micro E Weld Head Users Guide: Setup, Operation, and Maintenance Comprehensive user guide for the Sunstone Micro E Weld Head, detailing setup procedures, operational modes, maintenance instructions, and technical specifications for advanced electromagnetic linear motion micro welding applications.
	Sunstone Orion x-Series Pulse Arc Welders: Features, Specs, and Benefits Explore the Sunstone Orion x-Series pulse arc welders, featuring advanced technology like Tru-Fire®, Smart Energy Release, and WeldIQ™ for superior weld strength, speed, and ROI. Details on Orion 150x and 200x models.
	Sunstone Zapp User Guide: Permanent Jewelry Welder Comprehensive user guide for the Sunstone Zapp permanent jewelry welder, covering setup, operation, electrode care, and accessory mounting. Includes product specifications and information on related Orion models.